Keysight 10076C User manual

Keysight 10076C
High Voltage Probe
Characteristics
System Bandwidth • 500 MHz when used with 500 MHz bandwidth
oscilloscope
• Oscilloscope bandwidth when used with oscilloscope
with ≤ 150 MHz bandwidth
System Risetime (Calculated) • < 0.7 n sec when used with 500 MHz oscilloscope
• Oscilloscope risetime when used with oscilloscope
with ≤ 150 MHz bandwidth
Attenuation Ratio 100:1
Input Resistance
(when terminated into 1 MΩ)
66.7 MΩ
Input Capacitance ≈3 pF
Maximum Input
(pollution degree 2)
3700 Vpk (2650 Vrms) (mains isolated)
2650 Vdc (mains isolated)
1000 Vpk (dc + ac peak) CAT II (post receptacle mains)
DO NOT connect to a circuit above these maximums.
Compensation Range 6 - 18 pF
Probe Readout Yes
Operating Temperature 0 °C to 50 °C
Humidity 90% RH Non-condensing
Shock 400g 1/2 sine wave on tip end
50g 1/2 sine wave on BNC end
Propagation Delay ≈8 ns (1.8 m probe cable length)
Altitude 3000 m (indoor use only)

Probe Derating Curve (frequency limits measurable voltage)
Included Accessories
Item Description Qty
1 Retractable Hook Tip Adapter 1
2GroundLead 1
3 Insulation Cap 1
4MeasuringPin 2
5 Identification Tags 8
6 Spring Ground Tip (order N2789A) 1
NOTE: Items 1-5 are included in the 10077A replacement accessory kit. Order N2789A
for a replacement spring ground tip (qty 1).
When using any accessory, the probe assembly-accessory combination is only rated for
measurements on mains isolated circuits, not CAT II, III, or IV circuits.
100 KHz 1 Mhz 10 MHz 100 MHz 1,000 MHz
10 Vpk
100 Vpk
1,000 Vpk
3,700 Vpk Maximum input
Mains Isolated: 3700 Vpk
CAT II: 1000 Vpk
Mains Isolated
CAT II
This yellow part:
Adjust C to stabilize gain
covering frequency range
1
2
3
4
5
6

Inspecting the Probe
On receiving the shipment, inspect the probe and its accessories. If there is a
mechanical damage or a defect, or if the probe does not operate properly or
pass calibration tests, notify your Keysight Technologies Sales Office.
Verifying the Ground Level
The GND level can be confirmed when the probe is connected to the signal line.
This is achieved by observing the signal waveform and pressing the GND switch.
Cleaning the Probe
If the probe requires cleaning, disconnect it from the oscilloscope and gently
clean it with a soft cloth dampened with a mild soap and water solution. Wipe
with clean water to remove the detergent and then dry thoroughly with a clean
cloth. Make sure that the probe is completely dry before reconnecting it to an
oscilloscope.
Returning the Probe for Service
For all repair, service, or calibration needs, you can send the probe to an
authorized service center. Visit http://www.keysight.com/find/assist to find a
service location.
Safety Checks and Warnings
This probe has a cable with a built-in wear indicator. When the
insulation of the cable deteriorates, the wear indicator
becomes visible. Do not use the probe when the contrasting
color (black) is visible through the cable jacket. Using a product
with a worn cable may result in electric shock, fire, or
equipment failure.
Avoid contact of the probe cable with hazardous live voltages.
The rated voltage of the probe tip is higher than the rated
voltage of the probe cable. If the cable contacts hazardous live
voltages, it will not provide adequate protection. Contact of the
cable with hazardous live voltages may result in electric shock,
fire, or equipment failure.
When using the N2789A Spring Ground Tip accessory, the
spacing between the ground tip and probe tip when in use must
be a minimum of 25.2mm.
If the probe is used in a manner not specified by the
manufacturer, the protection that the probe provides may be
impaired.
WARNING
WARNING
WARNING
NOTE

Instrument Markings
© Keysight Technologies 2014, 2018
1900 Garden of the Gods Road
Colorado Springs, CO 80907
*10076-92007*
10076-92007, August 2018
Printed in Japan
The CE mark is a registered trademark of the European Community.
This product complies with the WEEE Directive (2002/96/EC)
marking requirements. The affixed label indicates that you must not
discard this electrical/ electronic product in domestic household
waste. Product Category: With reference to the equipment types in
the WEEE Directive Annex I, this product is classed as a “Monitoring
and Control instrumentation” product. Do not dispose in domestic
household. To return unwanted products, contact your local
Keysight office, or refer to www.keysight.com for more information.