KGuard Security KG-SH122E.V2 User manual

KGUARD Standalone DVR KG-SH122E.V2_SH222E.V2_SH522E.V2_User Manual(Hardware)
www.kguardsecurity.com
All rights reserved
1
KGUARD Standalone DVR
KG-SH122E.V2/222E.V2/522E.V2
User Manual
【
【【
【Hardware】
】】
】
2011-02-21

KGUARD Standalone DVR KG-SH122E.V2_SH222E.V2_SH522E.V2_User Manual(Hardware)
www.kguardsecurity.com
All rights reserved
2
Safety Precautions
Do Not touch live electrical parts.
Electric shock can be avoided. Follow the recommended practices listed below. Faulty
installation, improper grounding, and incorrect operation and maintenance of electrical
equipment are always sources of danger.
Do Not try to install equipment outdoor, when the wind and rain is strong.
Do Not install or remove equipment outdoor ,when the weather is raining.
Do Not try to install or operate any equipment , when the thunderstorm happened.
Always round all electrical equipment and the work platform.
Prevent accidental electrical shocks. Connect power source, control cabinets, and work platform to
an approved electrical ground.
Always use the correct cable size.
Sustained overloading will cause cable failure and result in possible electrical shock or fire hazard.
Work cable should be the same rating as the torch cable or factory .
Always keep cables and connectors in good condition.
Improper or worn electrical connections can cause short circuits and can increase the chance of an
electrical shock. Do not use worn, damaged, or bare cables.
Always avoid open-circuit voltage.
The added voltages increase the severity of the shock hazard.
Always wear insulated gloves while you adjust equipments.
Power should be shut off and insulated gloves should be worn when making any equipment
adjustment to assure shock protection.
Always wear protective clothing such as long sleeve shorts while you are installing or
removing equipments.
Always Wear high, snug fitting shoes.
Always Wear clean clothes without grease or oil.
Do not wear clothing that has been stained with oil and grease. It may burn if ignited by the heat
of the arc.
Protect neighboring workers from exposure to arc radiation.
Always Wear long trousers or jeans while you are installing or removing equipments.
Always wear safety helmet or hard head and safety shoes before work.
Always keep the equipments in dry places.
Always wear safety harnesses/belt while you work in high places.
Always wear dry clothing and avoid moisture and water.
Always wear Public Safety Vest , while you work at night.
Make sure all electrical connections are tight, clean, and dry.
Make sure that you are well insulated and eliminate the electric static charge.

KGUARD Standalone DVR KG-SH122E.V2_SH222E.V2_SH522E.V2_User Manual(Hardware)
www.kguardsecurity.com
All rights reserved
3
Always wear dry gloves, rubber-soled shoes, or stand on a dry board or platform.
Always Follow recognized safety standards.
Always wear correct eye, ear, and body protection.
Always have second person on-site, while you work in the darkness places, poor ventilation
places and high places.
Make sure that you are well protected against arc flashes, mechanical injury, or other mishaps.
Make sure that the polarity of wire is correct, before installing equipments.
Always handle equipment with care.
Do Not block the ventilation of equipment.
Do Not put the magnetic parts around the Equipment.
Do Not put the objects on top of equipment.
Warning
This is the symbol for indicating any
potential hazard, risk or condition
requiring special attention The user
need to refer to the important
operating and maintenance or
servicing instructions.
Caution
The lighting flash with an arrow head
symbol, in an equilateral triangle, is
intended to alert the user There is
dangerous “voltage” presence near
by the product’s enclosure which
may be risk of person
information
This is the symbol for notice you
that more information in the other
pages or additional information
Environmental-friendly
This is the symbol for recycling , in
order to create the green planet

KGUARD Standalone DVR KG-SH122E.V2_SH222E.V2_SH522E.V2_User Manual(Hardware)
www.kguardsecurity.com
All rights reserved
4
LIMITATION OF LIABILITY
THIS PUBLICATION IS PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER
EXPRESS OR IMPLIED, INCLUDIN BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTIBILITY, FITNESS FOR ANY PARTICULAR PURPOSE, OR NON-INFRIN EMENT OF
THE THIRD PARTY’S RI HT.
THIS PUBLICATION COULD INCLUDE TECHNICAL INACCUACIES OR TYPO RAPHICAL
ERRORS. CHAN ES ARE ADDED TO THE INFORMATION HEREIN, AT ANY TIME, FOR THE
IMPROVEMENTS OF THIS PUBLICATION AND/OR THE CORRESPONDIN PRODUCT(S).
DISCLAIMER OF WARRANTY
IN NO EVENT SHALL THE SUPPLIER BE LIABLBE TO ANY PARTY OR ANY PERSON, EXCEPT FOR
REPLACEMENT OR REASONABLE MAINTENANCE OF THE PRODUCT, FOR THE CASES,
INCLUDIN BUT NOT LIMITED TO THE FOLLOWIN S:
ANY DAMA E OR LOSS, INCLUDIN BUT WITHOUT LIMITATION, DIRECT OR INDIRECT,
SPECIAL, CONSEQUENTIAL OR EXEMPLARY, ARISIN OUT OF OR RELATIN TO THE
PRODUCT;
PERSONAL INJURY OR ANY DAMA E CAUSED BY INAPPROPRIATE USE OR NE LI ENT
OPERATION OF THE USER;
UNAUTHORIZED DISASSEMBLE, REPAIR OR MODIFICATION OF THE PRODUCT BY THE
USER;
ANY PROBLEM, CONSEQUENTIAL INCONVENIENCE, OR LOSS OR DAMA E, ARISIN OUT
OF THE SYSTEM COMBINED WITH THE DEVICES OF THE THIRD PARTY;
ANY CLAIM OR ACTION FOR DAMA ES, BROU HT BY ANY PERSON OR OR ANIZATION BEIN
A PHOTO ENIC SUBJECT, DUE TO VIOLATION OF PRIVACY WITH THE RESULT OF THAT
SURVEILLANCE-CAMERA’S PICTURE, INCLUDIN SAVED DATA, FOR SOME REASON, BECOMES
PUBLIC OR IS USED FOR THE PURPOSE OTHER THAN SURVEILLANCE.

KGUARD Standalone DVR KG-SH122E.V2_SH222E.V2_SH522E.V2_User Manual(Hardware)
www.kguardsecurity.com
All rights reserved
5
FCC Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
This device may not cause harmful interference, and this device must accept any
interference received, including interference that may cause undesired operation.
FCC CAUTION!
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment
generates uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures.
Before using this user manual , please check the model name of DVR from sticker, due to
the user manual combined with 4 channels/8channels/16channels DVR together.
SH122E V2

4 Channels DVR
SH222E V2

8 Channels DVR
SH522E V2

16 Channels DVR

KGUARD Standalone DVR KG-SH122E.V2_SH222E.V2_SH522E.V2_User Manual(Hardware)
www.kguardsecurity.com
All rights reserved
6
TABLE OF CONTENTS
CHAPTER 1 SH-122E V2 OVERVIEW 8
Packing List ................................................................................................................................................ 8
Components ............................................................................................................................................... 9
Installation and Connections .................................................................................................................... 14
Hard Disc .................................................................................................................................................. 14
Camera & Monitor.................................................................................................................................... 16
PTZ CAMERA ............................................................................................................................................ 17
keyboard .................................................................................................................................................. 18
RS-485 keyboard or Terminal.................................................................................................................... 18
POS system ............................................................................................................................................... 18
CHAPTER 2 SH-222E V2 OVERVIEW 19
Packing List .............................................................................................................................................. 19
Components ............................................................................................................................................. 20
Installation and Connections .................................................................................................................... 26
Hard Disc .................................................................................................................................................. 26
Camera & Monitor.................................................................................................................................... 28
PTZ CAMERA ............................................................................................................................................ 29
keyboard .................................................................................................................................................. 30
RS-485 keyboard or Terminal.................................................................................................................... 30
POS system ............................................................................................................................................... 30
CHAPTER 3 SH-522E V2 OVERVIEW 31
Packing List .............................................................................................................................................. 31
Components ............................................................................................................................................. 32
Installation and Connections .................................................................................................................... 37
Hard Disc .................................................................................................................................................. 37
Camera & Monitor.................................................................................................................................... 38
PTZ CAMERA ............................................................................................................................................ 40
POS system ............................................................................................................................................... 41
CHAPTER 4 APPENDIX 42
Specification............................................................................................................................................. 42
Compatible device table ........................................................................................................................... 46

KGUARD Standalone DVR KG-SH122E.V2_SH222E.V2_SH522E.V2_User Manual(Hardware)
www.kguardsecurity.com
All rights reserved
7
Introduction:
The H.264 digital video/audio recorders are designed for use within a surveillance system
with limited space, and are a combination of a hard disc recorder, a video multiplexer, and a
web server.
To achieve the highest inter-connectivity and inter-operability, this series of digital
video/audio recorders are all based on industry-leading front-end to back-end surveillance
infrastructure. With state-of-the-art system architecture, powerful
compression/decompression engine, and intelligent recording algorithms, hexaplex operation
can be easily achieved without sacrificing the increasing demands of functionality,
performance, reliability, and availability in the surveillance industry.

KGUARD Standalone DVR KG-SH122E.V2_SH222E.V2_SH522E.V2_User Manual(Hardware)
www.kguardsecurity.com
All rights reserved
8
Chapter 1 SH-122E V2 Overview
Packing List
SH122E V2 Remote Controller Power Adapter Power Cord
CD
Quick Guide Screws
Optional items
RS-485 to RS-232 Converter
(optional)
RS-232 connector
(optional)
RS-232 Y-Cable
(optional)
If you would like to purchase the optional items, above, please contact the local
venders.

KGUARD Standalone DVR KG-SH122E.V2_SH222E.V2_SH522E.V2_User Manual(Hardware)
www.kguardsecurity.com
All rights reserved
9
Components
A
B

KGUARD Standalone DVR KG-SH122E.V2_SH222E.V2_SH522E.V2_User Manual(Hardware)
www.kguardsecurity.com
All rights reserved
10
Area A (Front view)
No Symbol Button Functions
1 1-4 Alpha-numeric For selecting Channels.
Also, it can be used for typing text and number, when use mobile
functions.
2 Mode MODE For toggling between live mode and playback mode in main screen
display.
Also, as the function of “backward/slow backward ”, when you used the
playback mode.
3 SEQ SEQ For changing channels.
4 CALL CALL For switching to or return from full screen display of the focus camera in
main screen display.
5 SEARCH SEARCH For displaying the search menu.
6 REC RECORD For manual recording. To stop manual recording, press button once
again.
7 Play/Pause For playing the recorded images, or pausing the playback.
8 Stop For stopping the playback.
9 Copy For copying the playback images to the storage device connected to the
USB port. Press this button once to stop copying.
10 Menu/Esc MENU / ESC For displaying the main menu or exit to previous page.
11 Page Page In main screen display, press this button to enter/exit PTZ control if the
focus camera is a PTZ camera.
12 ▲/BS Up/BS As the function of moving up or focus window in normal operation.
*In PTZ control, it used for tilting up the camera.
**In text editing mode, the function as “**backspace” key.
13 ▼/DEL Down/DEL As the function of moving down or focus window in normal operation.
*In PTZ control, it used for tilting up the camera.
**In text editing mode, the function as “del” key.
***In playback mode, it used for single step.
14 ◄,► Left/Right In PTZ control, it is used for panning the camera.
In playback mode, the function as fast backward/forward.
In the other screens, it is used for cursor or focus window.
15 ENTER ENTER This button is used as “enter” key in normal operation.
*In PTZ control, this button is used to start/stop the selected PTZ control
mode.

KGUARD Standalone DVR KG-SH122E.V2_SH222E.V2_SH522E.V2_User Manual(Hardware)
www.kguardsecurity.com
All rights reserved
11
16
+ / -
Split Windows For next/previous split-window display.
LED indicator Main power, HDD and Network access indicators. 17
18
LEDs
IR sensor For receiving signal from I/R remote controller
19 U.S.B port For USB 2.0 compatible storage device
20 U.S.B port For USB MOUSE connection.
For detailed information, please refer to appendix.
Area B (Rear view)
No. Connector Functions
1 Video Input(camera) (1-4ch) For Camera video input(BNC connector/internal 75Ω
termination).
2 Video output(Main out) For video output(BNC connector)
3 Audio input For audio input(RCA connector)
4 Audio output (AUDIO) For audio output(RCA connector)
5 Ethernet socket For internet connection
6 V A For V A output (optional D-SUB 15-pin female connector).
7 RS-485 For RS-485 compatible PTZ camera(s) or keyboard.
8 Alarm Input (ALARM IN 1-4) For Connecting to external devices such as sensors or door
switches.
9 Alarm Output
(ALARM OUT NC/NO)
For connecting Alarm.
(Normally Closed (NC) (left), for alarm output) (Normally Open
(NO) (right) , for alarm output)
NC and NO only have 4 ports, Make sure that it is in
right position, before connection.

KGUARD Standalone DVR KG-SH122E.V2_SH222E.V2_SH522E.V2_User Manual(Hardware)
www.kguardsecurity.com
All rights reserved
12
Please note that only one of the NC or NO
connectors can be connected .
10 IR extension port(IR optional) For connection IR receiver(Optional)
11 Main Power switch(DC +12V) For DC 12V POWER SWITCH .
12 Power cord socket(DC +12V) For DC12V POWER INPUT.
For more information , please refer to appendix.
Remote Controller
No
Symbol Functions
1 REC Press to start the recording.
2 Alarm Reset Press to restore the alarm status to default.
3
Numeric/
alpha button
(1-9, 0, *, #)
For camera selection ,and also it can be used for entering
text and numbers.
The symol “#’ is also used for page down in
multi-split-window displays.
4 MENU/ESC For displaying the OSD menu and exit.
5 PTZ
Click to access the PTZ control when there is a PTZ camera
supported.
6 Mute/Next
Audio mute and the “Next” is used for choosing next text
when you typing the text in Text input.
7
X2/
OTO
*Zoom in/Zoom out(Digital Zoom (X2/X4))
*Click to view the image taken by PTZ camera at its preset
location.
8 Mode Press to switch between live and playback mode.
9 SEQ For changing channels.
10 Call
To call monitor and for video only(For switching to or
return from full screen display of the focus camera in
main screen display)
11 Search
To search the record video.
There are five types of search modes:
search by time, search by event, smart search, search

KGUARD Standalone DVR KG-SH122E.V2_SH222E.V2_SH522E.V2_User Manual(Hardware)
www.kguardsecurity.com
All rights reserved
13
archived files and POS search.
Enter For confirming the options or goto certain pages.
▲/BS: Click to move up or backspace for text/numeric entry.
*BS: BACKSPACE
◄ : ► LEFT/RI HT BUTTON.
12
▼/DEL
Click to move down or delete text for text/numeric entry.
13
/ /
(Volume/Zoom) +/- Buttons.
*In PTZ control, press these buttons to
zoom in/out the camera.
14 / To switch between different screen layouts.
Playback
Fast backward 2X,4X
Click to play or pause the playback.
Fast Forward 2X,4X,8X,16X
To copy the image to an external storage device.

Stop the playback, click again will back to normal record
mode.
Single Step the system will pause first and then jump to
next step.
MODE
Fast/slow backward 2x/4x/8x/16X
15
SEQ
Fast/slow forward 2x/4x/8x/16X
DVR1 – DVR4 16 Reserved
For environmental-friendly, please recycle the battery or use rechargeable battery.

KGUARD Standalone DVR KG-SH122E.V2_SH222E.V2_SH522E.V2_User Manual(Hardware)
www.kguardsecurity.com
All rights reserved
14
Installation and Connections
Hard Disc
Caution ！
！！
！
Do NOT install or remove hard drive while DVR is running!
Warning ！
！！
！
Make sure that you already turn off the power and disconnect the power cord,
Before performing any services or maintenances.
Warning ！
！！
！
Do NOT use electric screw-driver for installing or removing Hard Disc, when you
installing or removing Hard disc, or you will damage the Hard disc, Use screw driver
manual only.
Make sure to install one SATA hard disc (Max. storage size 2TB) inside the DVR
Step 1
Loosen 4 screws on the two sides of the case
(Using cross screw driver),(As shown).
Step 2
Remove the top cover by lifting and slide
back.(by hand)

KGUARD Standalone DVR KG-SH122E.V2_SH222E.V2_SH522E.V2_User Manual(Hardware)
www.kguardsecurity.com
All rights reserved
15
Step 3
Connect Hard Disc to the cable of SATA.
Step 4
Install the hard disc in the bracket, and tighten 4
screws on the side of hard disc(hand tight).
Before install the cover, make sure that
the cable all in the correct position without
loosing parts or cables.
Step 5
Install the top cover and tighten 4 screws on the
side of top cover(hand tight).
The HDD must be formatted before use.
For more information of H.D.D format, please
refer to Chapter 3.1.17.
(the system will detect the H.D.D and format
automatically, in the initial starting).
Step 6
Check the top cover to see it is in good
condition, and then connect the power cord.
Warning ！
！！
！
Make sure that the switch is in off position , before you connect the power
cord.

KGUARD Standalone DVR KG-SH122E.V2_SH222E.V2_SH522E.V2_User Manual(Hardware)
www.kguardsecurity.com
All rights reserved
16
Camera & Monitor
Warning ！
！！
！
Make sure that the switch is in off position ,before you connect the power cord. and also make sure
that the power is correct of adaptor.
Make sure to set the NTSC/PAL Selector Switch on the main board according to the local TV
system for the system to work correctly
(Connection diagram)
Items
Description
Camera
Connect the camera video input connectors to the video outputs
from system cameras or other composite video sources via coaxial
cables.
The internal 75Ω termination is always ON.
Power connector
Connect power source to DC 12V,3A
Monitor(VGA)
Connect the main monitor output connector (BNC) to a surveillance
TV monitor, or connect the VGA output connector to a V A monitor.
The TV/V A monitor displays selected live or recorded cameras in any
available split window format.
Monitor(Main out)
Connect the main monitor output connector (BNC) to a surveillance
TV monitor.
Audio input
Connect the audio input connector to the audio line-out from system

KGUARD Standalone DVR KG-SH122E.V2_SH222E.V2_SH522E.V2_User Manual(Hardware)
www.kguardsecurity.com
All rights reserved
17
cameras or other audio sources.
Audio output
Connect the audio output connector to the audio line-in from
speakers
Alarm inputs
Connect the alarm inputs to NC and/or NO type of alarm signals.
Alarm outputs
Connect the alarm output #1 to NC type of alarm signal, or alarm
output #2 to NO type of alarm signal.
Please note that only one of the NC or NO connectors can be
connected only.
Ethernet
Connect the Ethernet connector to a standard twisted-pair Ethernet
cable for remote access via LAN or internet.
I/R remote
controller
The user may use I/R remote controller to control the digital
video/audio recorder
PTZ CAMERA
Connect the RS-485 connector to PTZ camera(s) via the appropriate cable. The system
supports a variety of different PTZ cameras, including Pelco D protocol Dome, SamSung
SCC-641P, Kalatel Cyber Dome, Bosch AutoDome, etc.
But different PTZ cameras can coexist in a system only if they support the same
protocol.
Please make sure to set the PTZ ID of the camera(s), and setup the camera and
RS-232 or RS-422/485 accordingly.

KGUARD Standalone DVR KG-SH122E.V2_SH222E.V2_SH522E.V2_User Manual(Hardware)
www.kguardsecurity.com
All rights reserved
18
keyboard
RS-485 keyboard or Terminal
Connect the RS-485 connector to a RS-485 keyboard controller or VT-100 terminal via the
appropriate cables.
Please refer to the diagram above for the correct connection (as shown).
POS system
Connect the RS-485 connector to POS system via the appropriate cable. The system supports
the POS systems which can be connected to the following printers – Epson-TM200,
Epson-TMU295, Epson-TMU300, Epson-TMU675, Epson-TMT882, Epson-RPU420, and
Epson-MD332S. Please make sure to setup the RS-485 port accordingly.
*The connection of POS is for your reference only.
*The POS station, Printer , Y cable(RS-232),RS485 to RS-232 converter are optional items.
For Keyboard
RS-485+ TxD+
RS-485- TxD-
ND ND
For PTZ Device
R-S485+ RxD+(Data+)
RS-485- RxD-(Data-)
ND ND

KGUARD Standalone DVR KG-SH122E.V2_SH222E.V2_SH522E.V2_User Manual(Hardware)
www.kguardsecurity.com
All rights reserved
19
Chapter 2 SH-222E V2 Overview
Packing List
SH222E.V2 Remote Controller Power Adapter Power Cord
CD
Quick uide Screws
Optional items
RS-485 to RS-232 Converter
(optional)
RS-232 connector
(optional)
RS-232 Y-Cable
(optional)
If you would like to purchase the optional items, above, please contact the local
venders.

KGUARD Standalone DVR KG-SH122E.V2_SH222E.V2_SH522E.V2_User Manual(Hardware)
www.kguardsecurity.com
All rights reserved
20
Components
A
B