Kichler Lighting Ceiling fan User manual

 2*
 2*
Kichler®Lighting
7711 East Pleasant Valley Road
P.O. Box 318010
Cleveland, Ohio 44131-8010
Customer Service
866.558.5706
8:30 AM to 5:00 PM EST,
Monday - Friday
Instruction Manual
Universal Ceiling Fan Light Fixture
A Kichler®Select light fixture
™
Designed to coordinate with a popular Kichler®ceiling fan

1
1. SAFETY RULES
WARNING! RISK OF ELECTRIC SHOCK
All electrical connections must be made in
accordance with local codes, ordinances, or
national codes. If you are unfamiliar with
installing electrical wiring, secure the services
of a qualified electrician. Before starting this
installation, disconnect the power by turning
off the circuit breaker at your main panel or
removing the fuse at the fuse block. Turning
the power off using the ceiling fan switch
(speed control on/off) is not sufficient to
prevent electrical shock.
NOTE: The important safeguards and
instructions appearing in this manual are not
meant to cover all possible conditions and
situations that may occur. It must be
understood that common sense, caution and
care are factors which cannot be built into any
product. These factors must be supplied by the
person (s) caring for and operating the unit.
"CAUTION-RISK OF FIRE"
CONSULT A QUALIFIED ELECTRICIAN TO ENSURE
CORRECT BRANCH CIRCUIT CONDUCTOR.
2. PACKAGE CONTENTS
Unpack your fan and check the contents. You
should have the following items:
a. Light fixture
b. Glass shade
c. 13 watt compact fluorescent bulbs (2)
d. Part bag contents:
Nut
Spring washer
Pull chains and fobs (2)
wire nuts (2)
a
b
c
d

2
Fig. 1
Fig. 2
Light kit
assembly
Wire connector
Screws
Mounting plate
Universal Light Fixture Kit
Light kit
Nut
Lock washer
Center
plug
Switch
housing
3. INSTALLING THE LIGHT KIT
1. Remove and discard the center plug from
the switch housing. Attach the light kit to the
switch housing by feeding the light kit wires
(black and white) through the hole in the
center of the switch housing, then screw the
light kit onto the switch housing.
Attach the nut & lock washer on the inside of
the switch housing making sure the light kit is
secure to prevent movement after installation.
(Fig. 1)
2. Locate the white and blue wires inside the
switch housing labeled FOR LIGHT.
3. Attach the wires from the light kit to the
wires inside the switch housing by pushing the
polarized connections together.
- White wire to White wire
- Black wire to Black wire
4. Raise and hold the light kit assembly close
to the mounting plate of the ceiling fan. Push
the square wire connectors together. (Fig. 2)
NOTE: The square connectors are color
coded. Match the color coded sides of each
plug and push. They will attach ONLY when
matched correctly.
5. Carefully push all wires back into the switch
housing, then install the light kit assembly onto
the mounting plate with 3 screws provided. Be
sure to tighten all screws. (Fig. 2)
6. Remove the decorative metal nut and the
screw from the chain holder on the edge of the
light kit. Slip the beaded pull chain from switch
housing into the hole on the edge of the light
kit. (Fig. 2)
Decorative metal nut
Chain holder
Beaded pull chain

4. INSTALLING THE LIGHT BULBS &
GLASS SHADE
1. Install both of the 13 watt compact
fluorescent bulbs (provided), one in each
fixture socket. (Fig. 3)
2. Now place the glass shade over the light kit
stem. Secure the shade with a lock washer
and metal nut (rubber side touching the
shade). (Fig. 3)
3. Your installation is now complete. Restore
electrical power and enjoy your new ceiling fan
light kit. Feed the beaded pull chain from the
light kit stem through the hole in the decorative
nut and thread the decorative nut on securely.
DO NOT OVER TIGHTEN.
4. Your installation is now complete. Restore
electrical power and enjoy your new ceiling fan
light kit.
3
Fig. 3
Glass shade
Glass cap
Metal nut
Lock washer
Decorative nut
BulbsBulbs
Lamp holder