Kicker PowerBar KPB1 User manual

select language
seleccione el idioma
choisir la langue
sprache auswählen
KICKER PowerBar
KPB1 | KPB2
Amplified Weatherproof Bar-Mount Speaker System with Bluetooth
Sistema de alto-falantes Amplificado à prova de intempéries com Bluetooth
Système d’enceintes Amplifiées étanches à Montage sur Barre avec Bluetooth
Verstärktes Wetterfestes Bar-Mount-Lautsprechersystem mit Bluetooth
Owner’s Manual
Manual del Propietario
Manuel d’utilisation
Benutzerhandbuch

1English
Contents
Overview........................ 2
Specifications........................ 3
Installation ...................... 4
Wiring ................................... 4
Mounting............................... 5
Operation....................... 7
Status LED............................ 7
Control Panel ........................ 8
Setting Input Source .............. 9
Broadcast Mode ................... 9
Remote Control Install.......... 10
Remote Control Operation ... 10
Troubleshooting............ 11

2English
Overview
IMPORTANT SAFETY WARNING
PROLONGED CONTINUOUS OPERATION OF AN AMPLIFIER, SPEAKER, OR
SUBWOOFER IN A DISTORTED, CLIPPED OR OVER-POWERED MANNER
CAN CAUSE YOUR AUDIO SYSTEM TO OVERHEAT, POSSIBLY CATCHING
FIRE AND RESULTING IN SERIOUS DAMAGE TO YOUR COMPONENTS
AND/OR VEHICLE. AMPLIFIERS REQUIRE UP TO 4 INCHES (10CM) OPEN
VENTILATION. SUBWOOFERS SHOULD BE MOUNTED WITH AT LEAST 1
INCH (2.5CM) CLEARANCE BETWEEN THE FRONT OF THE SPEAKER AND
ANY SURFACE. KICKER PRODUCTS ARE CAPABLE OF PRODUCING SOUND
LEVELS THAT CAN PERMANENTLY DAMAGE YOUR HEARING! TURNING UP A
SYSTEM TO A LEVEL THAT HAS AUDIBLE DISTORTION IS MORE DAMAGING
TO YOUR EARS THAN LISTENING TO AN UNDISTORTED SYSTEM AT THE
SAME VOLUME LEVEL. THE THRESHOLD OF PAIN IS ALWAYS AN INDICATOR
THAT THE SOUND LEVEL IS TOO LOUD AND MAY PERMANENTLY DAMAGE
YOUR HEARING. PLEASE USE COMMON SENSE WHEN CONTROLLING
VOLUME.
The KICKER PowerBar-series of powered,
bar-mounted Bluetooth speakers provides you with
the power and clarity required for enjoying audio
in any outdoor and recreational setting. Featuring
an IP66 rating for weatherproof applications, the
PowerBar-series comes with an easy-to-use control
panel and mountable remote control, so changing
the tunes is only a touch away. Meanwhile KICKER
engineers have done it again, introducing Broadcast
Mode technology to allow you to sync up two or more
KPB’s via Bluetooth! RCA input and auxiliary output
also allow for any combination of daisy-chaining KPBs
or other devices. Use the KPB1 or the larger KPB2 on
the beach, the links, the patio, off-road, or anywhere
you’re missing the music.
Use the following instructions to install and operate
your KPB and KPB Remote.

3English
Model: KPB1 KPB2
Power Output
@ 14.4V, <10% THD+N
150W 300W
Woofer [in, mm] 3, 76
Tweeter [in, mm] 1, 25
Wiring Harness Length [ft,
m]
10, 3.05
Frequency Response [Hz] 50-20,000
Signal-to-Noise Ratio >75, A-weighted
re: rated power
Tweeter Magnet Material Neodymium
Tweeter Dome Material Titanium
Tweeter Design Dome
Woofer Cone Material Polypropolene
Woofer Surround Material Santoprene
Aux Input Stereo 3.5mm Female
0–1.75 V Sensitivity
RCA Output Stereo 3.5mm Female
Buffered, 2.5 V
Specifications

4English
Installation
Wiring
Disconnect the vehicle’s battery to avoid an electrical
short. Connect the KPB’s black ground wire to a
paint-and-corrosion-free, solid, metal area of the
vehicle’s chassis, or to the negative battery terminal.
Connect the KPB’s red power wire to the positive
battery terminal. Install a 15A fuse for the KPB1
or 30A fuse for the KPB2 between the KPB
and the power source. The fuse should be within
18” (45cm) of the power source and in-line with the
harness’ red power cable, which is connected to the
KPB. The wiring loom may be removed to assist with
installation, however this is not recommended and will
void the product’s warranty.
12V
LINE-OUT
gray
AUX IN
black
fuse
battery
to chassis ground or battery
IMPORTANT: The KPB draws a small amount
of power over time, even when off. If storing
the vehicle for two weeks or more, take
precautions to ensure the life of your vehicle’s
battery, such as disconnecting the fuse.
≤18”
(45cm)

5English
Keep the audio signal cable away from factory wiring
harnesses and other power wiring. If you need to
cross this wiring, cross it at a 90-degree angle.
Mounting
The KPB-series mounts natively to bar cylinders with
included bar clamp diameter sizes of 1.5”, 1.75”, and
2”. Use the KPB Square Clamps (LINK GOES HERE)
- sold separately - to mount your KPB to square
bars. Choose a structurally sound location to mount
the KPB. The KPB may be mounted below or above
bars. Make sure there are no items interfering with the
route of the wiring. The KPB2 may be mounted above
or below the bars, while the Mounting Base may be
rotated ± 30° to accommodate some curved bars.
Installation tools are not provided. 5mm and 6mm
Allen Wrenches are required.
1. Screw the Mounting Bases to the PowerBar using
the Mounting Screws.

6English
2. Place the Clamp Rings around your mounting bar
and secure the Clamp Rings to the Mounting Bases
using the Clamp Screws.
The KPB2 may be mounted with the bases and
clamps in an inward, or outward configuration

7English
Operation
Status LED
LED color displays audio source, pairing status, and
warnings:
Flashing Blue - in pairing mode
Solid Blue - connected bluetooth device
Red - 1/8” (3.5mm) auxiliary input
Bluetooth (Blue)
Off Power is off
Solid Bluetooth Connected
Rapid Blinking Bluetooth Pairing Mode
Alternate Red/Blue Waiting for Broadcast Mode
to connect
Long Blue + Short Red Wireless Broadcast Mode
active - Bluetooth input
AUX IN (Red)
Off Power is off
Solid Source is AUX
Alternate Red/Blue Waiting for Broadcast Mode
to connect
Long Red + Short Blue Broadcast Mode active -
AUX input
Other
Red Rapid Blinking AMP FAULT Warning
(Overload, Undervoltage,
Overvoltage)
Red+Blue Rapid Blinking AMP OTW Warning (Over
Temperature)

8English
Control Panel
EQ
Long Press - Power On/Off
Power on the KPB by
performing a long press of
the POWER Button
EQ
Increase Volume Decrease Volume
Short Press - Previous Track
Long Press - Rewind
Short Press - Next Track
Long Press - Fast Forward
Short Press - Play/Pause or Mute
Very Long Press (10s) - Software Reset
Short Press - Change Input Source
Long Press - Enter Bluetooth Pairing Mode
Change EQ Presets - KICKER, LOUD,
SOUND QUALITY, & VOICE
1S
10S
short press
long press
very long press

9English
Setting Input Source
Short Press the SOURCE button to switch between
Bluetooth (blue) and AUX IN (red) input sources.
To enter Bluetooth Pairing Mode, Long Press the
SOURCE button while in Bluetooth mode. The
STATUS LED will begin to flash blue. You may exit
pairing mode at this stage by short pressing the
SOURCE button.
To finish pairing, from your audio device select either
‘KPB1 KICKER’ or ‘KPB2 KICKER’. When successfully
connected, the STATUS LED will be solid blue. When
the PowerBar powers on in, or enters, Bluetooth
mode, it will automatically begin to search for and
connect with the last connected device. If that device
is not found, it will continue to search for other saved
connections until a connection is established.
Broadcast Mode
Broadcast Mode allows you to play your audio
through two KPBs. One KPB, the Primary, will
broadcast the audio to the Secondary KPB. EQ
settings applied by the Primary will be mirrored on the
Secondary. Broadcast Mode is compatible with both
audio input sources. You may enter Broadcast Mode
with the following button sequence.
1. Set audio input source with the Primary KPB.
2. Simultaneously Press & Hold the PLAY/PAUSE
button and the Increase Volume button on the Primary
KPB. The Status LED will begin alternately flashing
blue and red.
3. Simultaneously Press & Hold the PLAY/PAUSE
button and the Decrease Volume button on the
Secondary KPB.

10English
Remote Control Install
The remote control must be charged via USB micro
5V power input.
Install the included remote control to your steering
wheel as follows:
1. Place the KPB onto the wheel facing the user in
the position in which it will be most used.
2. With the lock open, place the two arms of the
remote control around the steering wheel.
3. Pull the lock down over the open slot on the
adjacent arm.
Remote Control Operation
Increase Volume Decrease Volume
Sync to KPB
after charging
and mounting
Short Press - Previous Track
Long Press - Rewind
Short Press - Next Track
Long Press - Fast Forward
Short Press - Play/Pause or Mute
Double-Press - Sync to KPB
Short Press - Change Input Source
Long Press - Enter Bluetooth Pairing Mode

11English
Troubleshooting
If the KPB becomes frozen or stuck during algorithmic calculation, does not
appear to be working, or gives an error code, check the obvious things first
such as blown fuses, poor or incorrect wiring connections, incorrect setting
of gain controls, etc.
No power? With a Volt Ohm Meter (VOM) check the following: +12 volt
power terminal (should read +12V to +16V) Check for reversed power
and ground connections Ground terminal, for proper conductivity.
Power on, no signal? Check the following: RCA connections Test
audio source signal, either with a “known good” output device or other
means.
Bluetooth device will not connect? On your mobile device: Turn
Bluetooth off, then on again. Remove ‘KPB1/2 KICKER’ from the
Bluetooth menu. Then pair again (see page 9). Move your mobile device
closer to the speaker. Avoid obstacles that may block the wireless signal.
Perform a factory reset by pressing and holding the PLAY/PAUSE button
for 10 seconds.
No or low output? Check the settings on the audio source. Check
the RCA (or speaker input) and speaker output connections.
KPB frozen or stuck in operating procedure? Perform factory reset
the KPB Cycle the power
Broadcast Mode will not engage? Follow the instructions to enter
Broadcast Mode on page 9. Perform a factory reset on both primary
and secondary KPBs.
CAUTION: When jump starting the vehicle, be sure that connections
made with jumper cables are correct. Improper connections can result in
blown fuses as well as the failure of other critical systems in the vehicle.
If you have more questions about the installation or operation of your new
KICKER product, see the Authorized KICKER Dealer where you made your
purchase. For more advice on installation, click on the SUPPORT tab on
the KICKER homepage, www.KICKER.com. Choose the TECHNICAL
SUPPORT tab, choose the subject you are interested in, and then
download or view the corresponding information. Please E-mail support@
KICKER.com or call Technical Services (405) 624-8583 for unanswered or
specific questions.

12English
Warranty
When purchased from an Authorized KICKER Dealer, KICKER
warrants this product to be free from defects in material and
workmanship under normal use for a period of TWO (2) YEARS from
date of original purchase with receipt. If this product is identified as
“Refurbished” or “B Goods”, the warranty is limited to a period of
THREE (3) MONTHS from the date of original purchase. In all cases
you must have the original receipt. Should service be necessary
under this warranty for any reason due to manufacturing defect
or malfunction during the warranty period, KICKER will repair or
replace (at its discretion) the defective merchandise with equivalent
merchandise. Warranty replacements may have cosmetic scratches
and blemishes. Discontinued products may be replaced with more
current equivalent products. This warranty is valid only for the original
purchaser and is not extended to owners of the product subsequent
to the original purchaser. Any applicable implied warranties are limited
in duration to a period of the express warranty as provided herein
beginning with the date of the original purchase at retail, and no
warranties, whether express or implied, shall apply to this product
thereafter. Some states do not allow limitations on implied warranties;
therefore, these exclusions may not apply to you. This warranty gives
you specific legal rights; however you may have other rights that vary
from state to state.
WHAT TO DO IF YOU NEED WARRANTY OR SERVICE:
Defective merchandise should be returned to your local Authorized
Stillwater Designs (KICKER) Dealer for warranty service. Assistance
in locating an Authorized Dealer can be found at www.KICKER.com
or by contacting Stillwater Designs directly. You can confirm that
a dealer is authorized by asking to see a current authorized dealer
window decal.
If it becomes necessary for you to return defective merchandise
directly to Stillwater Designs (KICKER), call the KICKER Customer
Service Department at (405) 624-8510 for a Return Merchandise
Authorization (RMA) number. Package only the defective items in a
package that will prevent shipping damage, and return to:
Stillwater Designs, 3100 North Husband St, Stillwater, OK 74075
47KPB-a-20

13English
The RMA number must be clearly marked on the outside of the
package. Please return only defective components. The return
of functioning items increases your return freight charges. Non-
defective items will be returned freightcollect to you. For example,
if a subwoofer is defective, only return the defective subwoofer, not
the entire enclosure. Include a copy of the original receipt with the
purchase date clearly visible, and a “proof-of-purchase” statement
listing the Customer’s name, Dealer’s name and invoice number, and
product purchased. Warranty expiration on items without proof-of-
purchase will be determined from the type of sale and manufacturing
date code. Freight must be prepaid; items sent freight-collect, or
COD, will be refused.
WHAT IS NOT COVERED?
This warranty is valid only if the product is used for the purpose for
which it was designed. It does not cover:
o Damage due to improper installation
o Subsequent damage to other components
o Damage caused by exposure to moisture, excessive heat,
chemical cleaners, and/or UV radiation
o Damage through negligence, misuse, accident or abuse. Repeated
returns for the same damage may be considered abuse
o Any cost or expense related to the removal or reinstallation of
product
o Speakers damaged due to amplifier clipping or distortion
o Items previously repaired or modified by any unauthorized repair
facility
o Return shipping on non-defective items
o Products with tampered or missing barcode labels
o Products with tampered or missing serial numbers
o Products returned without a Return Merchandise Authorization
(RMA) number
o Products purchased from an UNAUTHORIZED dealer
o Freight Damage
o The cost of shipping product to KICKER
o Service performed by anyone other than KICKER
HOW LONG WILL IT TAKE?
KICKER strives to maintain a goal of one week turnaround for
all electronics (amplifiers, crossovers, equalizers, etc.) returns.
Delays may be incurred if lack of replacement inventory or parts is
encountered. Failure to follow these steps may void your warranty.
Any questions can be directed to the KICKER Customer Service
Department at (405) 624-8510. Contact your International KICKER
dealer or distributor concerning specific procedures for your country’s
warranty policies.

FCC WarningThis device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interferenceto radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:-Reorient or relocate the receiving antenna.·Increase the separation between the equipment and receiver.·Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.·Consult the dealer or an experienced radio/TV technician for help.Radiation Exposure Statement To comply with FCC RF exposure compliance requirements, this grant is applicable to only mobile configurations. The antennas used for this transmitter must be installed to provide a separation distance of at least 20cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.
Other manuals for PowerBar KPB1
1
This manual suits for next models
1
Table of contents
Other Kicker Speakers System manuals

Kicker
Kicker QS60.2 User manual

Kicker
Kicker KM60 User manual

Kicker
Kicker PS692 User manual

Kicker
Kicker KM620.2 User manual

Kicker
Kicker KMT67 User manual

Kicker
Kicker I350 User manual

Kicker
Kicker QS65.2 User manual

Kicker
Kicker 1350 User manual

Kicker
Kicker KS5.2 User manual

Kicker
Kicker KMT6 User manual