Kicker KSMT25 User manual

EOP2021-CS4
5/26/2021
REV-A.1
49KSMT25 Installation Guide
Page 1of 6
The Kicker KSMT25 pod provides a mid and tweeter with optimized adjustability. The
pod can be mounted to almost any surface where a hole can be drilled. Not only does the entire
pod assembly pivot, lean, and rotate on the ball and socket mounting stud - the tweeter also has
approximately 260 degrees of planetary rotation around the mid to provide desired orientation.
This document demonstrates adjusting, mounting, and wiring of the KSMT25 pod assembly for
the following Kicker models:
•47KSMT2504
PARTS IDENTIFICATION
Below is a list describing part names used in these instructions.
(1) KSMT25 pod assembly
(2) Tweeter
(3) Mid
(4) Mounting Stud
(5) Decorative Plug
(6) Washer
(7) Wing Nut
READ AND UNDERSTAND ALL OF THESE INSTRUTIONS BEFORE
INSTALLATION!
(1)
(2)
(3)
(4)
(5)
(6)
(7)

EOP2021-CS4
5/26/2021
REV-A.1
49KSMT25 Installation Guide
Page 2of 6
ADJUSTABILITY OF THE KSMT25 POD
The KSMT25 tweeter pod assembly pivots and rotates on its mounting stud. This can be
accomplished any time before or after installation.
1. To adjust the rotation of the tweeter around the mid, remove the decorative plug at the
back of the pod assembly. Using a 2.5mm allen wrench, loosen (do not remove) the bolt
retaining the tweeter to the mid.
2. Rotate the tweeter to the desired location and retighten the bolt. Replace the decorative
plug.

EOP2021-CS4
5/26/2021
REV-A.1
49KSMT25 Installation Guide
Page 3of 6
TIGHTENING THE BALL AND SOCKET MOUNT
If the pod assembly will not remain stationary on the stud, the ball and socket clamp can
be tightened to prevent pod movement.
1. Remove the nut and washer from the stud.
2. Using a 2mm allen wrench, tighten the three bolts on the bottom of the pod to increase
clamping force on the ball and socket.
MOUNTING THE KSMT25 TWEETER POD
Choose a mounting surface that can be accessed from both side as a wing nut must be
installed on the mounting stud to retain the pod in its location.
1. Drill a 5/8” in the desired mounting location.

EOP2021-CS4
5/26/2021
REV-A.1
49KSMT25 Installation Guide
Page 4of 6
2. Place the washer on the mounting stud then insert the mounting stud into the drilled hole
Secure the pod assembly to the mounting surface with the wing nut.
CONNECTING THE CROSSOVERS TO THE PODS
DANGER! Electrical hazard. Burns, electric shock, or damage to equipment
may occur during connection of electrical wires. Always disconnect the vehicle’s
power source before making wire connections.
Kicker supplies crossovers with KSMT25 to optimize the sound of the pod’s speakers.
The KSMT25 crossover is terminated so that it will only connect to the KSMT25 assembly.

EOP2021-CS4
5/26/2021
REV-A.1
49KSMT25 Installation Guide
Page 5of 6
NOTE: The KSMT25 crossover is labeled with the part number 47KSMT25-XO.
1. Connect the crossover terminals and receptacles to their respective mating connector on
the KSMT25 pod assembly. The terminals on the 47KSMT25 crossover are all different
sizes and types to prevent incorrect connection. Also, the crossover wire colors match the
pod assembly wire colors.

EOP2021-CS4
5/26/2021
REV-A.1
49KSMT25 Installation Guide
Page 6of 6
2. Slide the clear cover over the terminals to prevent a short circuit.
3. Connect the crossover input to the outputs of the head unit or amplifier using the supplied
butt connectors. The positive lead is the wire with gray insulation labeled with a “plus”
symbol. The negative lead has gray insulation with a black stripe on it.