Kidde SLED177i User manual

ATTENTION! The model SLED177i strobe light is designed to notify hearing impaired
individuals of impending danger. The strobe light has no detection means and MUST be
used in conjunction with operating and interconnected Smoke, Heat, or Carbon
Monoxide Alarms.
The model SLED177i AC wire-in Strobe light can be directly interconnected with Kidde
Safety 3-wire Smoke, Heat and CO alarms. It will produce an intermittent strobe flash
pattern (approximately 4 flashes, followed by approximately 5 seconds off) when trig-
gered by a Carbon Monoxide alarm and a flash every second when triggered by a
smoke or heat alarm.
Thank you for purchasing this strobe light. It is an important part of your family’s home
safety plan. You can trust KIDDE Safety to provide the highest quality safety products.
We know you expect nothing less when the lives of your family are at stake.
For model: SLED177i
1102-7201-00
Strobe
Light
For your convenience, write down the following information. If you call
our Consumer Hotline, these are the first questions you will be asked.
Strobe Light Model Number
(located on back of alarm):
Date Code (located on back of device):
Date of Purchase:
Where Purchased:
SLED177i
Strobe Light User Guide
1102-7201-00_Rev.A_EN_V8:_ 2013.5.28 9:45 AM Page 1

IMPORTANT! READ ALL INSTRUCTIONS BEFORE INSTALLATION AND SAVE
THIS USER GUIDE FOR FUTURE REFERENCE
WARNING! THIS VISUAL SIGNALING DEVICE HAS NO DETECTION
MEANS. IT MUST BE USED IN CONJUNCTION WITH OPERATING AND
INTERCONNECTED ALARMS.
WARNING! DO NOT TRY TO REPAIR THIS STROBE LIGHT YOURSELF
REFER TO THE INSTRUCTIONS IN SECTION 11 FOR SERVICE.
WARNING! DISCONNECTING OR LOSS OF AC POWER WILL RENDER
THIS SIGNALING DEVICE INOPERATIVE.
WARNING! THIS STROBE LIGHT IS EXTREMELY BRIGHT. DO NOT LOOK
DIRECTLY AT THE LIGHT WHEN THE LIGHT IS FLASHING..
CONTENTS OF THIS USER GUIDE
1 -- SPECIFICATIONS
2 -- APPLICATIONS
3 -- RECOMMENDED APPLICATIONS OF STROBE LIGHTS
4 -- LOCATIONS TO AVOID
5 -- INSTALLATION INSTRUCTIONS
6 -- OPERATION AND TESTING
7 -- MAINTENANCE
8 -- LIMITATIONS OF SIGNALING DEVICES FOR THE HEARING IMPAIRED
9 -- GOOD SAFETY HABITS
10 -- NFPA PROTECTION STANDARD 72
11 -- SERVICE AND WARRANTY
!
!
!
!
1102-7201-00_Rev.A_EN_V8:_ 2013.5.28 9:45 AM Page 2

1. SPECIFICATIONS
Model Number: SLED177i ( 3 WIRE INTERCONNECT UNIT )
Electrical Rating: Regulated 120VAC (96-132VAC)
Maximum Operating RMS Current 630 mA
Multiple station (24) interconnect unit, interfaces directly with Kidde
Safety:
Ion Smoke Alarm Models: 1235, 1275, 1276, 1285, i12020, i12020A
i12040, i12040A, i12060,i2060A, i4618,
i4618A, KN-SMFM-I, RF-SM-ACDC
Photo Smoke Alarms: PE120, P12040,
Photo / Ion Smoke Alarms: Pi2000, Pi2010,
Heat Alarm Models: HD135F,
CO / Ion Smoke Alarm Models: KN-COSM-I,KN-COSM-IB,
KN-COPE-I,KN-COSM-IC,
CO / Photo Smoke Alarm Models: KN-COPE-I,
Carbon Monoxide Alarms Models: KN-COB-IC,KN-COP-IC
Strobe Light: SLED177i, SL177i
Relay Modules: SM120X, CO120X
Smoke or heat alarm events: Constant 1 flash per second nominal
Flash Rate (CO alarm event): Intermittent 1 flash per second nominal
(approximately 4 flashes, followed by
approximately 5 seconds OFF)
Temperature Limits: 0°C (32°F) to 49°C (120°F)
Mounting: Wall or Ceiling
Applications: Primary Direct or Indirect and Supplementary
Light Output: 177 Candela minimum (on axis
measurement)
1102-7201-00_Rev.A_EN_V8:_ 2013.5.28 9:45 AM Page 3

The following diagram shows that the light intensity gradually decreases as the
viewing angle is increased. Use this information to determine the best location
for the strobe light.
2. APPLICATIONS
PRIMARY DIRECT AND INDIRECT VISIBLE SIGNAL
Locate the strobe light on the ceiling in the center of the room or on
the wall a minimum of 80"(2 m) above the floor.
For rooms larger than 250 sq. ft. (14 ft. by 16 ft. - 4.27m by 4.88 m) the
notification device should be located within 16 feet of the pillow when located in a
sleeping area.
SUPPLEMENTARY VISIBLE SIGNAL
The strobe must be located more than 30 inches above the floor.
3. RECOMMENDED LOCATIONS OF VISUAL SIGNALING DEVICES
• Locate the first strobe light in the bedroom in which the hearing impaired
individual sleeps. If the bedroom door is kept closed at night, an
interconnecting smoke detector must also be installed in that bedroom.
• Locate additional strobe lights in any lived-in room where a hearing impaired
individual would need to be notified of an alarm condition.
4. LOCATIONS TO AVOID
• In direct sunlight or high ambient light areas; the bright light may reduce one’s
ability to notice the strobe light.
•
In areas where the temperature may fall below 0°C (32°F) or rise above 49°C (120°F).
• In areas with high humidity.
• Do not use outdoors (This device is not listed for outdoor use).
WALL
CEILING
25 90
25 85
30 80
30 75
35 70
35 65
40 60
45 55
55 50
75 30-45
90 5-25
100 0
(LIGHT INTENSITY) (IN DEGREES)
PERCENT ANGLE
90°
90°
90° 90°
0°
0°
45°
45°
45°45°
SOURCE
LIGHT
SOURCE
LIGHT
WALL
CEILING
25 90
25 85
30 80
30 75
35 70
35 65
40 60
45 55
55 50
75 30-45
90 5-25
100 0
(LIGHT INTENSITY) (IN DEGREES)
PERCENT ANGLE
90°
90°
90° 90°
0°
0°
45°
45°
45°45°
SOURCE
LIGHT
SOURCE
LIGHT
1102-7201-00_Rev.A_EN_V8:_ 2013.5.28 9:45 AM Page 4

5. INSTALLATION INSTRUCTIONS
READ CAREFULLY – WIRING REQUIREMENTS
• This smoke alarm should be installed on a U.L. listed or recognized junction
box. All connections should be made by a qualified electrician and all wiring
used shall be in accordance with articles 210 and 300.3(B) of the U.S. National
Electrical Code ANSI/NFPA 70, NFPA 72 and/or any other codes having jurisdic-
tion in your area. The multiple station interconnect wiring to the alarms must
be run in the same raceway or cable as the AC power wiring. In addition, the
resistance of the interconnect wiring shall be a maximum of 10 ohms.
• The appropriate power source is regulated 120VAC (96-132VAC) AC single
phase supplied from a non-switched circuit, which is not protected by a ground
fault interrupter.
MODEL SLED177i WIRING INSTRUCTIONS: For AC QUICK CONNECT 3 WIRE HARNESS.
WARNING: This alarm cannot be operated from power derived from a
square wave, modified square wave or modified sine wave inverter. These type
of inverters are sometimes used to supply power to the structure in off grid
installations, such as solar or wind derived power sources. These power sources
produce high peak voltages that will damage the strobe light.
CAUTION! TURN OFF THE MAIN POWER TO THE CIRCUIT BEFORE
WIRING THE STROBE LIGHT.
1. When Strobe lights and alarms are interconnected, all the interconnected
devices must be powered from the same circuit.
2. A maximum of 24 Kidde Safety devices may be interconnected in a multiple
station arrangement. The interconnect system should not exceed the NFPA
interconnect limits of 12 smoke alarms and/or 18 alarms total (smoke, heat,
Carbon Monoxide, etc). With 18 interconnected alarms it is still possible to
interconnect up to a total of 6 remote signaling devices and/or relay modules.
NOTE: WHEN MIXING MODELS WHICH HAVE BATTERY BACKUP (1275,
1275CA, 1276, 1276CA, 1285, i12040, i12040CA, i12040A, i12040ACA,
i12060, i12060CA, i12060ACA, i12080, i4618, i4618CA, KN-SMFM-I-CA,
PE120, PE120CA, P12040, P12040ACA, Pi2000CA, Pi2010, Pi2010CA,
KN-COSM-IB, KN-COSM-IBCA, RF-SM-ACDC, HD135, KN-COB-IC, KN-COB-IC-CA,
KN-COP-IC, KNCOP-IC-CA,KN-COPE-I, KN-COPE-ICA) WITH MODELS WITHOUT
BATTERY BACKUP (1235, 1235CA, i12020, i12020CA, i12020A, i12020ACA,
KN-COSM-I, KN-COSM-ICA, KN-COB-ICB-CA, CO120X, SM120X AND SL177i,
SLED177iCA), BE ADVISED THAT THE MODELS WITHOUT BATTERY BACKUP WILL
NOT FUNCTION DURING AN AC POWER FAILURE.
!
!
1102-7201-00_Rev.A_EN_V8:_ 2013.5.28 9:45 AM Page 5

4. The maximum wire run distance between the first and last device in an inter-
connect system is 1000 ft.
5. Figure 1 illustrates interconnection wiring. Improper connection will result in
damage to the strobe light or alarms, failure to operate, or a shock hazard.
6. Make certain that all devices in the interconnect system are wired to a contin-
uous (non-switched, non-GFI or GCFI protected) power line.
FIGURE 1: INTERCONNECT WIRING DIAGRAM.
N
N
L
WIRE NUT
WIRE NUT
OR
OR
EQUIVALENT
EQUIVALENT
WHITE
WHITE
BLACK
BLACK
RED
RED
WHITE
WHITE
RED
RED
BLACK
BLACK
WHITE
WHITE
WHITE
WHITE
RED
RED
RED
RED
BLACK
BLACK
BLACK
BLACK
FUSE OR CIRCUIT BREAKER
FUSE OR CIRCUIT BREAKER
SMOKE ALARM
SMOKE ALARM
STROBE LIGHT
STROBE LIGHT
HEAT ALARM
HEAT ALARM
CO ALARM
CO ALARM
FIGURE 1
WIRING OF STROBE AC QUICK CONNECT THREE WIRE HARNESS
WIRES ON ALARM HARNESS CONNECTED TO:
BLACK HOT SIDE OF AC LINE
WHITE NEUTRAL AC LINE
RED INTERCONNECT LINES (RED WIRES) OF THE OTHER UNITS IN
THE MULTIPLE STATION SET UP
1102-7201-00_Rev.A_EN_V8:_ 2013.5.28 9:45 AM Page 6

MOUNTING INSTRUCTIONS:
• A mounting plate is provided on the back of the strobe light. This mounting
plate is installed on the electrical box between the electrical box and the
strobe light.
• Remove the mounting plate from the back of the strobe light by holding the
mounting plate and twisting the strobe light in the direction indicated by the
"OFF" arrow on the cover.
CAUTION: THIS UNIT IS SEALED. THE COVER IS NOT REMOVABLE! After
selecting the proper strobe light location as described in section 3, and wiring
the AC QUICK CONNECT harness as described in the WIRING INSTRUCTIONS,
attach the mounting plate to the electrical box (see fig. 2).
FIGURE 2: SELECT PROPER MOUNTING HOLES ON THE MOUNTING PLATE
• Use a screwdriver to punch out only the pair of holes in the mounting plate
that match your type of electrical box or plaster ring. Mount the mounting
plate to the electrical box using the appropriate holes. NOTE: Use the circle,
square, and octagon markings near each mounting hole in the mounting plate
to help you select the correct mounting holes (see fig. 2).
Rectangular
Plaster Ring
Circular
Plaster Ring
Octagonal
Electrical Box
FIGURE 2
!
1102-7201-00_Rev.A_EN_V8:_ 2013.5.28 9:45 AM Page 7

• Pull the AC QUICK CONNECTOR through the center hole in the mounting plate and
install the mounting plate, making sure that the mounting screws are positioned in
the small ends of the keyholes before tightening the screws (see fig. 2).
• Plug the AC QUICK CONNECTOR into the back of the strobe light, (see fig. 3)
making sure that the locks on the connector snap into place. To remove AC con-
nector, squeeze locking arm and pull.
• If you have finished all the WIRING AND MOUNTING PLATE MOUNTING STEPS,
you can install the strobe light on the mounting plate. Alignment marks are
provided on the side of the strobe light and mounting plate. With the indicating
marks aligned and rotate the strobe light in the direction of the ON arrow on
the cover until the strobe light snaps in place. (See fig. 4)
• Turn on the AC power. The model SLED177i strobe light has a green AC
power on indicator which should be lit when the strobe is correctly powered.
TAMPER RESIST LOCKING PIN: To make your strobe light tamper resistant a
locking pin has been provided with your strobe light. Using this pin will help
deter individuals from removing the strobe light from the mounting plate. To use
the pin insert it into the hole in the side of the strobe light after the strobe light
has been installed on the mounting plate (see fig. 5). NOTE: The tamper resist
pin will have to be removed in order to remove the strobe light. This can be
done easily with a long nose pliers. Using the long nose pliers, pull the pin out
of the hole, it is now possible to remove the strobe light from the mounting
plate.
After installation test your strobe light by following the test procedure outlined
in section 6.
Tamper resistant
locking pin
Alignment Marks
FIGURE 3 FIGURE 4 FIGURE 5
Install Remove
1102-7201-00_Rev.A_EN_V8:_ 2013.5.28 9:45 AM Page 8

CAUTION! Early warning fire detection and visual notification is best
achieved by the installation of fire detection and visual notification equipment in
all rooms and areas of the household as follows: A smoke alarm and visual
notification device installed and interconnected in each separate sleeping area,
and visual notification equipment interconnected with heat, smoke, or CO
alarms in the living rooms, dining rooms, kitchens, hallways, attics, furnace
rooms, closets, utility storage rooms, basements, and attached garages.
6. TESTING AND OPERATION
WARNING! THIS STROBE LIGHT IS EXTREMELY BRIGHT. DO NOT LOOK
DIRECTLY AT THE LIGHT .
TESTING: Push the test button on one of the interconnected alarms to activate
the test sequence for the alarm.
The controlling alarm will also send an activation signal through the
interconnecting wiring to the strobe light, and cause the strobe light to flash if
the strobe light and the interconnection wiring are working properly.
If the strobe does not activate check the fuse or circuit breaker supplying power
to the alarm circuit.
If the strobe does not activate perform the maintenance steps in the alarm’s
User Guide.
Check the operation of the strobe light by executing a test on another
interconnected alarm.
TEST THE STROBE LIGHT AND YOUR ALARMS WEEKLY TO ENSURE
PROPER OPERATION.
OPERATION: The strobe light is operating once AC power is applied, the green
LED is illuminated, and testing is complete. When the strobe light is activated by
an interconnected alarm, it will flash for as long as the controlling alarm remains
active.
7. MAINTENANCE
STROBE LIGHT REMOVAL:
IF TAMPER RESIST PIN HAS BEEN USED, REFER TO “TAMPER RESIST LOCKING
!
!
1102-7201-00_Rev.A_EN_V8:_ 2013.5.28 9:45 AM Page 9

PIN” IN SECTION (5) FOR PIN REMOVAL INSTRUCTIONS.
CLEANING YOUR STROBE LIGHT:
To clean your Strobe light remove it from the mounting plate and disconnect the
AC Quick Connect power harness as outlined in section 5.
You can clean dust from your strobe light by using a vacuum cleaner hose and
vacuuming around the cover and lens openings on the strobe light.
The outside of the strobe light can be wiped with a damp cloth.
AFTER CLEANING, REINSTALL YOUR STROBE LIGHT AND TEST YOUR
STROBE LIGHT BY ACTIVATING ONE OF THE CONTROLLING ALARMS.
8. LIMITATIONS OF ALARM CONTROLLED VISUAL SIGNALING
DEVICES
VISUAL SIGNALING DEVICES CAN PROVIDE EARLY WARNING TO HEARING
IMPAIRED INDIVIDUALS AT A REASONABLE COST; HOWEVER, IN ORDER FOR
THE VISUAL SIGNALING DEVICE TO FUNCTION, IT MUST BE ACTIVATED BY AN
OPERATING ALARM. ALARMS CANNOT PROVIDE AN ACTIVATION SIGNAL TO
THE VISUAL SIGNALING DEVICE IF SMOKE, HEAT OR CARBON MONOXIDE DO
NOT REACH THE SPECIFIC ALARM. THEREFORE, ALARMS MAY NOT SENSE A
CONDITION ON A DIFFERENT FLOOR, OR ON THE OTHER SIDE OF A CLOSED
DOOR. ALARMS DO HAVE LIMITATIONS. AC POWERED ALARMS WILL NOT
OPERATE IF AC POWER HAS BEEN CUT OFF BY AN ELECTRICAL FIRE OR AN
OPEN FUSE.
HOME EMERGENCIES DEVELOP IN DIFFERENT WAYS AND ARE OFTEN UNPRE-
DICTABLE. NO ONE TYPE OF CONTROLLING ALARM; HEAT, FIRE (IONIZATION OR
PHOTOELECTRIC) OR CARBON MONOXIDE IS ALWAYS BEST. FOR MAXIMUM
PROTECTION, ALARMS MUST BE INSTALLED IN EACH SLEEPING AREA, AND ON
EVERY LEVEL OF A HOME. ALARMS MUST BE INTERCONNECTED WITH EACH
OTHER AND THE SIGNALING DEVICES AND BE TESTED REGULARLY TO INSURE
THE ALARMS AND INTERCONNECTING CIRCUITS ARE IN GOOD OPERATING
CONDITION.
IN AN UNDERWRITERS LABORATORIES STUDY, THIS TYPE OF VISUAL SIGNALING
APPLIANCE WAS ONLY SUCCESSFUL IN WAKING 92% OF THE SLEEPING
RESPONDENTS.
HEARING IMPAIRED INDIVIDUALS MAY NOT SEE THE VISUAL WARNING DEVICE
IF WALLS, DOORS, DISTANCE, HIGH AMBIENT LIGHT, OR OTHER OBSTRUCTIONS
BLOCK THE STROBE LIGHT. IF THE STROBE LIGHT IS LOCATED OUTSIDE THE
1102-7201-00_Rev.A_EN_V8:_ 2013.5.28 9:45 AM Page 10

BEDROOM OR ON A DIFFERENT FLOOR, IT WILL NOT WAKE UP A SOUND
SLEEPER. THE USE OF ALCOHOL OR DRUGS MAY ALSO IMPAIR ONE’S
ABILITYTO RESPOND TO THE VISUAL SIGNAL.
ALTHOUGH VISUAL SIGNALING DEVICES CAN HELP SAVE LIVES BY PROVIDING
AN EARLY WARNING OF AN EMERGENCY SITUATION, THEY ARE NOT A SUBSTI-
TUTE FOR AN INSURANCE POLICY. HOME OWNERS AND RENTERS SHOULD
HAVE ADEQUATE INSURANCE TO PROTECT THEIR LIVES AND PROPERTY.
9. GOOD SAFETY HABITS
DEVELOP AND PRACTICE A PLAN OF ESCAPE
• Install and maintain Fire extinguishers on every level of the home and in the
kitchen, basement and garage. Know how to use a fire extinguisher prior to
an emergency.
• Make a floor plan indicating all doors and windows and at least two (2)
escape routes from each room. Second story windows may need a rope or
chain ladder.
• Have a family meeting and discuss your escape plan, showing everyone what
to do in case of fire.
• Determine a place outside your home where you all can meet if a fire occurs.
• Familiarize everyone with the sound of the smoke alarm and train them to
leave your home when they hear it.
• Practice a fire drill at least every six months, including fire drills at night.
Ensure that small children hear the alarm and wake when it sounds. They
must wake up in order to execute the escape plan. Practice allows all occu-
pants to test your plan before an emergency. You may not be able to reach
your children. It is important they know what to do.
• Current studies have shown smoke alarms and notification devices may not
awaken all sleeping individuals, and that it is the responsibility of individuals in
the household that are capable of assisting others to provide assistance to
those who may not be awakened by the alarm sound or to those who may be
incapable of safely evacuating the area unassisted.
1102-7201-00_Rev.A_EN_V8:_ 2013.5.28 9:45 AM Page 11

WHAT TO DO WHEN THE ALARM ACTIVATES
• Alert small children in the home.
• Leave immediately by your escape plan. Every second counts, so don’t waste
time getting dressed or picking up valuables.
• In leaving, don’t open any inside door without first feeling its surface. If hot,
or if you see smoke seeping through cracks, don’t open that door! Instead,
use your alternate exit. If the inside of the door is cool, place your shoulder
against it, open it slightly and be ready to slam it shut if heat and smoke rush
in.
• Stay close to the floor if the air is smoky. Breathe shallowly through a cloth,
wet if possible.
• Once outside, go to your selected meeting place and make sure everyone is
there.
• Call the fire department from your neighbor’s home - not from yours!
• Don’t return to your home until the fire officials say that it is all right to do so.
There are situations where a smoke alarm may not be effective to protect
against fire as stated in the NFPA Standard 72. For instance:
a) smoking in bed
b) leaving children home alone
c) cleaning with flammable liquids, such as gasoline
10. NFPA REQUIRED PROTECTION
For your information the National Fire Protection Association's Standard 72, pro-
vides information regarding the fire detection equipment required within the
family living unit. And reads as follows:
Smoke Detection. Where required by applicable laws, codes, or standards for the
specified occupancy, approved single- and multiple-station smoke alarms shall be
installed as follows: (1) In all sleeping rooms. (2) Outside of each separate
sleeping area, in immediate vicinity of the sleeping rooms. (3) On each level of
the dwelling unit, including basements. Exception: In existing one- and two-
family dwelling units, approved smoke alarms powered by batteries are
permitted.
1102-7201-00_Rev.A_EN_V8:_ 2013.5.28 9:45 AM Page 12

Smoke Detection - Are More Smoke Alarms Desirable? The required number of
smoke alarms might not provide reliable early warning protection for those areas
separated by a door from the areas protected by the required smoke alarms. For
this reason, it is recommended that the householder consider the use of
additional smoke alarms for those areas for increased protection. The additional
areas include the basement, bedrooms, dining room, furnace room, utility room,
and hallways not protected by the required smoke alarms. The installation of the
smoke alarms in the kitchen, attic (finished or unfinished), or garage is normally
not recommended, as these locations occasionally experience conditions that
can result in improper operation.
This equipment should be installed in accordance with the National Fire
Protection Association’s Standard 72 (NFPA, Batterymarch Park, Quincy, MA
02269).
NOTIFY YOUR LOCAL FIRE DEPARTMENT AND INSURANCE COMPANY OF YOUR
SMOKE ALARM AND STROBE ALARM INSTALLATION.
11. SERVICE AND WARRANTY
If after reviewing this user guide you feel that your Visual Signaling Device is
defective in any way, do not tamper with the unit. Return it for servicing to:
KIDDE SAFETY, 1016 Corporate Park Dr., Mebane, NC. 27302 (See Warranty for
in-warranty returns).
1102-7201-00_Rev.A_EN_V8:_ 2013.5.28 9:45 AM Page 13

TEN YEAR LIMITED WARRANTY
KIDDE Safety warrants the original purchaser that the enclosed Visual signaling Device
will be free of defects in material and workmanship or design under normal use and
service for a period of ten years from the date of purchase. The obligation of KIDDE
Safety under this warranty is limited to repairing or replacing the Visual Signaling Device
or any part which we find to be defective in material, workmanship or design, free of
charge to the customer, upon sending the Visual Signaling Device with proof of date of
purchase, postage and return postage prepaid to: Warranty Service Department, Kidde
Safety, 1016 Corporate Park Dr., Mebane, NC 27302.
This warranty shall not apply to the Visual Signaling Device if it has been damaged,
modified, abused, or altered after the date of purchase or if it fails to operate due to
inadequate AC electrical power.
THE LIABILITY OF KIDDE SAFETY OR ANY OF ITS PARENT OR SUBSIDIARY
CORPORATIONS ARISING FROM THE SALE OF THIS VISUAL SIGNALING DEVICE OR
UNDER THE TERMS OF THIS LIMITED WARRANTY SHALL NOT IN ANY CASE EXCEED
THE COST OF REPLACEMENT OF THE VISUAL SIGNALING DEVICE, AND IN NO CASE
SHALL KIDDE SAFETY OR ANY OF ITS PARENT OR SUBSIDIARY CORPORATIONS BE
LIABLE FOR CONSEQUENTIAL LOSS OR DAMAGE RESULTING FROM THE FAILURE OF THE
VISUAL SIGNAL ING DEVICE OR THE BREACH OR THIS OR ANY OTHER WARRANTY,
EXPRESSED OR IMPLIED, EVEN IF THE LOSS IS CAUSED BY THE COMPANIES
NEGLIGENCE OR FAULT.
Since some states do not allow limitations on the duration of an implied warranty or do
allow the exclusion of limitations or incidental or consequential damages, the above
limitation or exclusions may not apply to you. While this warranty gives you specific legal
rights, you may also have other rights which vary from state to state.
The above warranty may not be altered except in writing signed by both parties hereto.
QUESTIONS OR FOR MORE INFORMATION
Call our Consumer Hotline at 1-800-880-6788 or contact
us at our website at www.kidde.com
Kidde, 1016 Corporate Park Drive, Mebane, NC 27302
1102-7201-00_Rev.A_EN_V8:_ 2013.5.28 9:45 AM Page 14