Kilews KP-AUX-TL-450 User manual

Auxiliary Arm Manual
Axial rotation
KILEWS INDUSTRIAL CO., LTD.
http://www.kilews.com
Y2F220B-002
KP-AUX-TL-450
KP-AUX-TL-700

1
Table of contents
I.
Introduction ･･･････････････････････････････････
2
II.
Feature ･･･････････････････････････････････････
2
III.
Items ･････････････････････････････････････････
3
IV.
Precautions･････････････････････････････････････
4
1. Sign definitions ･･････････････････････････････
4
2. Safety notifications ････････････････････････････
4
V.
Description ････････････････････････････････････
5
1. Assembly ･･･････････････････････････････････
5
2. Dimension ･････････････････････････････････
3. Conditions of use ･･･････････････････････････
6
6
VI.
Installation ････････････････････････････････････
7
1. Fitting tool ･･････････････････････････････････
7
2. Spring adjustment ･････････････････････････････
8
VII.
Maintenance ･･･････････････････････････････････
8

2
I. Introduction
In order to prevent injuries, an auxiliary torque arm has been added to reduce torsion and
weight of the screwdriver. Each auxiliary arm corresponds to ergonomics for additional safety
measures.
II. Feature
A total 360°rotation of main pole plus 325° swing ability on axial arm allows the screwdriver
to reach different devices at ease. In addition, the adjustable spring balancer can stop
screwdriver from lifting up and down at anywhere that is not only helping to increase work
efficiency but also productivity. [Figure 1]
【Figure 1】

3
III. Items
Item no.
Objects
Qty.
Diagram
KL-T5000B
Spring balancer set I.
KL-T5000(AUX-TL450)
1
KL-T7000B
Spring balancer set II.
KL-T7000(AUX-TL700)
KP20032L
Main pole set I. (Linear bearing
set included)
KP-AUX-TL450
1
KP20032L-1
Main pole set II. (Linear bearing
set included)
KP-AUX-TL700
KP20033L
Axial arm set I. (Fixture included)
KP-AUX-TL450
1
KP20033L-1
Axial arm set II. (Fixture
included)
KP-AUX-TL700
KP20007-7
Base plate
1
PP0122
Accessory kits
(Allen key 6mm & screws)
1

4
IV. Precautions
For use of this product properly, avoid jeopardizing personal and property safety of the lives of
others, to prevent the occurrence of danger and be sure to read the instructions carefully
<Please be sure to follow instruction>
1. Sign definitions
【PROHIBITION】Attempting to perform without notice may cause body
injury or damage to the auxiliary arm.
【WARNING】Attempting to perform without notice may cause body injury
or damage to your objects.
2. Safety notification
Follow instructions in this manual and operate machine correctly.
Do not spread unknown contaminants to the machine such as oil or water.
Modification and disassembly are not allowed.
Keep hand in the safty area while machine is operating.
Measure tool’s weight and adjust balancer to a proper position.
Please maintain and clean the machine regularly.

5
V. Description
1. Assembly - Arm
Unpack box and take all components out and then assembly by following steps carefully.
(a.)Using 4 M6*25L hex screws to tight machine base (5) on your workstation.
(b.)Place a main pole set (2) way down to the bottom of base and tight screws slightly. (Note: Be proper
tightening screws for better rotation controlling.) Turn linear bearing set to aim a thread hole at above then
add a M6*20L screw to tight up. (a screw size of M8*20L is for KL-T7000B)
(c.)Put an axial arm set (3) (label faces outside) onto the concave area of linear bearing part and then tight two
M8*35L hex screws along with washers. (a screw size of M10*40L is for KL-T7000B)
(d.)Put the spring balancer on the top of main pole and then tight a M6*20L hex screw on top.
(e.)Connect the spring balancer (1) and linear bearing set (2) together.
(f.) Be sure to measure tool’s weight and adjust balancer to a proper position. See page 8 to find spring setting.

6
2. Dimension
3. Condition of use
Model
Weight
kg
Place
of use
Operating
Temperature
Operating Humidity
Screwdriver’s
weight (kg)
Max. Torque
Kgf-cm
Operating
area
mm
TI-450
Approx.
6.9
Indoor
－5℃~ 60℃
(NO freezing)
20％~ 90％
(NO condensation)
~ kg
150
475
TI-700
Approx.
9.5
~ kg
250
700

7
VI. Tool installation guide
1. Fitting tool (1) Before clamp a tool, make sure auxiliary arm is seated at the lowest position, and
spring has released it tension.
(2) Follow the instructions to clamp a screwdriver and tight with M6*50 screws. The
available dimension of fixture for screwdriver is from ψ25mm to ψ46mm.
(3) In order to prevent unexpected force from spring and cause any injury, make sure to
flow instructions from the item 1 when replace or release the screwdriver.
Caution
1.1 Put flange on TCG screwdriver before clamped to avoid damage form fixture.
1.2 Make sure to adjust flange slightly right after tightening up and shift holes of flange away from
screwdriver’s thread carefully to avoid screws harming thread.
1.3 Make sure the TCG screwdriver is seated vertical to fixture before tightening up.
1.4 The replacement procedure of the auto shut off screwdriver is the same as TCG type but no need flange.

8
2. Spring adjustment
VII. Maintenance
For better condition and extending life cycle of this machine, please clean and maintain
regularly.
1. Daly Lubricate the machine with the industrial oil like WD-40 daily as a frequent user.
2. WeeklyAdd proper greases into the linear bearing part weekly. [Figure 2]
You may shorten maintenance time period, if the machine has been used under a bad
weather condition or a higher frequent use.