kim lighting Bell EL 160 User manual

Bell™Accent / Pathlighter Installation Instructions
Reviised 7/16/10 ECN 100715008 Status 9 Part No. 95617
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS
IMPORTANT SAFETY INSTRUCTIONS!
WARNING: Fixtures must be grounded in accordance with local codes or the National Electrical Code.
Portable spear or tree mounts using a cord and plug, must be plugged into a receptacle protected by a
Ground Fault Circuit Interrupter (GFCI) in accordance with the National Electrical Code. Failure to take these steps
may result in serious personal injury. Lighted lamp is HOT! Do Not touch hot lens, guard, or enclosure.
MAINTENANCE: To maintain light efficiency and prevent fixture overheating, lenses must be kept clean and free
of dirt, dust, leaves, trash and mineral deposits from water. For optimum performance a regularly scheduled
maintenance program should be followed. DO NOT operate luminaire with missing or damaged lens.
CAUTION: L.E.D. fixtures are available in 120 volt input or 277 volt input. Please verify before wiring fixture to
field wires (see lamp label to verify). KEEP THIS SHEET FOR FUTURE REFERENCE.
Tools Required: Flat Blade Screwdriver 3/32” Allen Wrench Adjustable Wrench Thread Sealant
1. Run wires through pole and thread
short thread into pole cap.
2. Coat threads with a good sealant
and install pole into desired
junction box. (Direct burial box for
H.I.D.)
5. Remove screws from lens frame
with a flat blade screwdriver.
6. Install lamp of type and wattage
shown on fixture label & chart.
Do not exceed maximum watt-
age. Re-install lens and lens
frame. (EL167, BN167 shown on
page 2.)
Installation Instructions: Make certain the electrical supply is OFF before starting fixture installation.
EL160
BN165
6160
6165
4. Make all necessary connections
observing polarity, i.e. green-to-
ground, white-to-common, and
black-to-voltage.
!
EL167
BN167
IMPORTANT!
For L.E.D. fixtures
only, verify input
voltage . See
CAUTION above.
3. Position fixture & tighten locknut
with adjustable wrench.
Par 20
Lamp
!
P.O. Box 60080 •16555 East GaleAve.
City of Industry, California 91716-0080
626/968-5666 • FAX [phone]

Page 2 Kim Lighting • 16555 E. Gale Ave. • P.O. Box 60080 • City of Industry, CA 91716-0080 • 626/968-5666 • FAX [phone]
Bell™Accent / Pathfinder Installation Instructions
How may we serve you better?
Please let us know. Visit our website at:
www.kimlighting.com
Your input matters to us.
LAMP INFORMATION
Cat. No. Lamp Type Max. Watts
INCANDESCENT
EL160 PAR20 50
BN165 A19 60
(By Others)
H.I.D.
6160 PAR20 35MH
6165 (By Others)
L.E.D.
EL167 L.E.D. 15
BN167 (By KIM)
WARNING!
The H.I.D. / Fluorescent fixture utilizes a lamp that may
contain mercury. For information on disposal of lamp, go to
website: www.lamprecycle.org
7. Loosen setscrew, adjust fixture rotation and
tighten setscrew (300° rotatable).
6. The EL167 and BN167 fixtures are equipped
with L.E.D. lamps from the factory. Make
sure the (4) lens cover screws are tightened
for proper sealing.
*L.E.D. IDENTIFIER
8. *L.E.D. identifier - both are available in 120
volt or 277 volt input. Reference label on
side of driver component or lamp label to
determine.
5 Watt 15 Watt
KIM LIGHTING LIMITED WARRANTY
When installed in accordance with Kim Installation Instructions and accepted
trade practices, the following shall apply:
General Product Limited Warranty Coverage
All material and component parts used in the manufacture of Kim Products, are
warranted to be free from defects of material and/or workmanship for a period
of 1 year from date of sale, with the following exceptions:
Auxiliary Equipment
All auxiliary equipment (such as lamps, ballasts, and transformers) provided by
and/or included in Kim Products shall carry the component manufacturer's
warranty.
Copper, Bronze and Brass Landscape Components
Copper and Bronze Landscape fixture components shall be warranted against
defects of material and/or workmanship, and failure due to corrosion, for a
period of 25 years from date of sale.
Kim Lighting's brass components are constructed from several brass parts
that are manufactured by various methods at various times. Since brass
naturally deepens in color as it ages through the normal oxidation process,
these parts may exhibit subtle differences in coloration when the product is
new. This is normal and expected. These color differences will be eliminated
shortly after installation through the normal brass oxidation process.
Composite In-Ground Components
Composite In-Ground fixture components installed below grade, shall be
warranted against defects of material and/or workmanship, and failure due to
corrosion, for a period of 7 years from date of sale.
Aluminum Landscape Components
Aluminum Landscape fixture components not in direct contact with soil, shall
be warranted against defects of material and/or workmanship for a period of 3
years from date of sale. Aluminum fixture components in direct contact with
soil shall be warranted from defects of material and failure from corrosion for a
period of 1 year from date of sale.
Limit of Liability and General Conditions
Only products which are installed, used and maintained in accordance with
applicable Kim instructions, specifications and accepted trade practices, are
covered by the Kim Warranty. During the warranty period, with proof of
purchase, Kim will repair or replace with the same or similar product, at Kim's
option, without charge. Labor costs are the owner's responsibility and are
excluded from this warranty. This warranty is void if the product is modified,
tampered with, misapplied, poorly installed, improperly maintained, or
subjected to abnormal conditons.
Repair or replacement as provided under this warranty is the exclusive
remedy of the purchaser. This warranty is in lieu of all other warranties,
expressed or implied, including any implied warranty of fitness for a particular
application. Kim Lighting shall not be liable to the purchaser for indirect or
consequential damages.