kim lighting KLV201 User manual

Accent Light - KLV201 Installation Instructions
P.O. Box 60080 • 16555 East Gale Ave.
City of Industry, California 91716-0080
626/968-5666 •FAX [phone]
INSTRUCTIONS PERTAINING TO A RISK OF FIRE OR INJURY TO PERSONS
IMPORTANT SAFETY INSTRUCTIONS!
WARNING - To reduce the risk of FIRE OR INJURY TO PERSONS: Do Notoverdrive fixtures with greater
than 12 volts or fixture over-heating and short lamp life will occur. Do Notoverload the transformer by
installing (or relamping) higher wattage lamps than planned. Note: Total wattage of all lamps connected to one
transformer must not exceed the capacity of that transformer. Do Notinstall luminaire within 10 feet (3.04m) of
a pool, spa, or fountain. DO NOT operate luminaire with missing or damaged lens.
SAFETY WARNING: When relamping be sure electrical supply is OFF. Low voltage fixtures can become
very hot depending on the lamp wattage used. Glass lenses and metal areas above & around the lamp can
become hot enough to blister hands. Use discretion when touching fixture and be sure to allow fixture to cool
before relamping. When relamping fixture avoid touching the lamp envelope with bare hands. If touching the
lamp is necessary during installation, clean the envelope with alcohol and dry with a clean, soft cloth before
turning ON. Contamination of the envelope may reduce the lamp performance. To maintain light efficiency and
prevent fixture-overheating, glass lenses and enclosure must be kept clean and free of dirt, dust, leaves, trash
(combustible materials) and mineral deposits from water. Particular care should be taken not to locate fixtures
where small children can reach them if higher wattage's are used.
NOTE: Keep the lamp free from impact while burning, as this may deform the filament and shorten the lamp life.
NOT INTENDED FOR INDOOR USE. All electrical work should be done by a qualified electrician.
KEEP THIS SHEET FOR FUTURE REFERENCE.
Part No. 95613Revision 7/16/10 ECN 100715008 Status 6
INSTALLATION INSTRUCTIONS:Make certain the electrical supply is OFF before starting fixture installation.
3. To install lamp, unscrew tension ring. NOTE:
Lamp installation is not accessible by removing
the glass lens.
4. Install lamp of type and wattage shown on
fixture label. NOTE: Add silicone grease to
screw threads each time fixture is relamped.
2. Attach fixture onto coupling. NOTE: KIM
“KLV Mounting Options” can be installed
before fixture is attached.
1. Tighten coupling onto mounting device.
(See KIM Installation Instructions for Low
Voltage Mounting Options, part no. 95488.)
Apply Silicone Grease
IMPORTANT
DRAIN HOLE IN SHIELD
MUST FACE DOWN!
Tension Ring
!
!
!
Tools Required:
Phillips Screwdriver
Adjustable Wrench
B” Hex Wrench
Silicone Grease
KLV201
Fixture
Coupling

Page 2 Kim Lighting • 16555 E. Gale Ave. • P.O. Box 60800 • City of Industry, CA 91716-0080 • 626/968-5666 FAX [phone]
KLV201 Installation Instructions
LAMP INFORMATION
CAT. NO. LAMP TYPE MAX. WATTS
KLV201 MR16 Bi pin 75
Halogen
*Note: Swivel stem must be installed with the
mounting threads facing down-to-horizontal.
Fixtures may not be installed with mounting
threads facing upward unless shielded from
rain or sprinklers.
180°
Adjustability
90°
*
*
FIXTURE ORIENTATION
(See *Note Below)
KIM LIGHTING LIMITED WARRANTY
When installed in accordance with Kim Installation Instructions and
accepted trade practices, the following shall apply:
General Product Limited Warranty Coverage
All material and component parts used in the manufacture of Kim
Products, are warranted to be free from defects of material and/or
workmanship for a period of 1 year from date of sale, with the following
exceptions:
Auxiliary Equipment
All auxiliary equipment (such as lamps, ballasts, and transformers)
provided by and/or included in Kim Products shall carry the
component manufacturer's warranty.
Copper and Bronze Landscape Components
Copper and Bronze Landscape fixture components shall be warranted
against defects of material and/or workmanship, and failure due to
corrosion, for a period of 25 years from date of sale.
Composite In-Grade Components
Composite In-Grade fixture components installed below grade, shall
be warranted against defects of material and/or workmanship, and
failure due to corrosion, for a period of 7 years from date of sale.
Aluminum Landscape Components
Aluminum Landscape fixture components not in direct contact with
soil, shall be warranted against defects of material and/or workmanship
for a period of 3 years from date of sale. Aluminum fixture components
in direct contact with soil shall be warranted from defects of material
and failure due to corrosion for a period of 1 year from date of sale.
Limit of Liability and General Conditions
Only products which are installed, used and maintained in accordance
with applicable Kim instructions, specifications and accepted trade
practices, are covered by the Kim Warranty. During the warranty
period, with proof of purchase, Kim will repair or replace with the same
or similar product, at Kim's option, without charge. Labor costs are the
owner's responsibility and are excluded from this warranty. This
warranty is void if the product is modified, tampered with, misapplied,
poorly installed, improperly maintained, or subjected to abnormal
conditions.
Repair or replacement as provided under this warranty is the exclusive
remedy of the purchaser. This warranty is in lieu of all other warranties,
expressed or implied, including any implied warranty of fitness for a
particular application. Kim Lighting shall not be liable to the purchaser
for indirect or consequential damages.
How may we serve you better?
Please let us know. Visit our website at:
www.kimlighting.com
Your concerns are important to us.
6. Loosen setscrew, adjust fixture rotation, and
tighten setscrew. Connect fixture to main
system cable with a KLV410 Sealed
Connector. (See KLV410 Installation
Instructions)
5. Adjust angle using swivel screw. Retighten
after adjustments.
Additional wire and connectors may
be purchased from Kim Lighting: KLV427 #12-2 Cable
KLV432 #8-2 Cable
KLV410 Connector
KLV411 Connector