Kinetico Premier Compact User manual
ENG
visit www.kinetico.co.uk
Installation and User Manual
Water Softener
Kinetico Premier Compact Water Softener Installation Instructions
2
For more information about Kinetico:
visit www.kinetico.co.uk
Kinetico UK Ltd
Bridge House, Park Gate Business Centre, Hants SO31 1FQ
www.kinetico.co.uk
3
For more information about Kinetico:
visit www.kinetico.co.uk
Kinetico UK Ltd
Bridge House, Park Gate Business Centre, Hants SO31 1FQ
Contents
Safety information 4
Contents of box 6
Specifications 6
Getting to know the softener 7
Pre-installation check list 8
Installation instructions 10
Installation review 12
Commissioning instructions 13
Useful information 16
Kinetico Premier Compact Water Softener Installation Instructions
4
Safety information
Read all information carefully prior to installing and using the
water softener.
Qualified Installer
Kinetico recommends that a qualified
installer performs the installation. Failure
to install the system as instructed could
invalidate the Limited Warranty.
Water Temperature
Do not install the Kinetico softener in
an area where the water temperature
can exceed 35°C or cause the unit
to freeze. Freezing temperatures will
damage the system.
Water Pressure
Do not install if the supply water pressure
exceeds 6 BAR (87 psi), unless a suitable
pressure regulating valve has been
installed on the softener water supply.
Overflow
VERY IMPORTANT:
Where a cabinet overflow could cause
damage, you must install a 1/2” I.D.
hose to the barbed fitting on the
cabinet and run to a suitable outlet
that is visible and capable of taking the
overflow (i.e. through the outside wall).
Make sure the hose does not go higher
than the barbed fitting as the water
will flow away using gravity.
INSTALLER
1
2
34
5
6
0bar
www.kinetico.co.uk
5
Copper/Plastic Pipework
Where copper and plastic pipework is
used, Kinetico advises adherence to
the regulatory requirements to ensure
adequate earth bonding is provided.
Intended Use
Not intended to be used for treating
water that is micro-biologically unsafe
or water that has an unknown quality,
without adequate disinfection before or
after the system.
WRAS Approval
WRAS approval for the Kinetico Premier
Compact Water Softener applies to cold
water (below 23°c) installations only.
Plumbing Schematic
Please refer to the plumbing schematic
on page 8 before commencing an
installation.
Inlet
InletOnly
Outlet
Kinetico Premier Compact Water Softener Installation Instructions
6
1 x in/out retaining
bracket and pin
Contents of box
Identify the following parts before proceeding.
Meter Disc Type 1 2 3 4 5 6 7 8
Max hardness
(in mg/L)
HE 57 120 173 241 309 379 448 507
HF 63 125 186 246 305 362 419 474
Litres between
regenerations
HE 2150 1075 717 537 430 358 307 269
HF 1961 980 654 490 392 327 280 245
Type HE HF
Cabinet dimensions (h x w x d) 498 x 219 x 468 mm 498 x 219 x 468 mm
Salt used per regeneration 0.34 kg 0.34 kg
Regeneration time 11 minutes 11 minutes
Flow rate @ 15 psi drop 16.6 L/m 33.3 L/m
Pipe connections - in/out ¾” BSP ¾” BSP
Min/max operating pressure 1.8 - 6 bar 1.8 - 6 bar
Min/max operating temperature 2 - 23˚C 2 - 23˚C
Specifications
Jubilee clip4 x o-ring
1 x 2cc silicone tube
2 x ¾” BSP
in/out adaptor
2 x ¾” screened washers 1 x blanking plate
www.kinetico.co.uk
7
Getting to know the softener
THIS DRAWING AND ITS CONTENTS ARE THE PROPERTY OF KINETICO
INCORPORATED. THEY HAVE BEEN LOANED TO YOU FOR A LIMITED TIME AND
PURPOSE, AND MAY NOT BE COPIED OR DUPLICATED WITHOUT THE WRITTEN
PERMISSION OF AN AUTHORIZED EMPLOYEE OF KINETICO INCORPORATED.
ADDITIONALLY, THE PROCESS, METHOD, DESIGN AND DATA CONTAINED HEREIN,
ARE CONSIDERED TO BE THE PROPERTY OF KINETICO INCORPORATED AND MAY
NOT BE DIVULGED TO ANY OTHER PERSON OR COMPANY NOR USED TO
KINETICO'S DISADVANTAGE
REV DESCRIPTION ECO DATE BY APPRVD
Salt compartment
Outlet
Overflow
Drain
connection
Inlet
THIS DRAWING AND ITS CONTENTS ARE THE PROPERTY OF KINETICO
INCORPORATED. THEY HAVE BEEN LOANED TO YOU FOR A LIMITED TIME AND
PURPOSE, AND MAY NOT BE COPIED OR DUPLICATED WITHOUT THE WRITTEN
PERMISSION OF AN AUTHORIZED EMPLOYEE OF KINETICO INCORPORATED.
ADDITIONALLY, THE PROCESS, METHOD, DESIGN AND DATA CONTAINED HEREIN,
ARE CONSIDERED TO BE THE PROPERTY OF KINETICO INCORPORATED AND MAY
NOT BE DIVULGED TO ANY OTHER PERSON OR COMPANY NOR USED TO
KINETICO'S DISADVANTAGE
REV DESCRIPTION ECO DATE BY APPRVD
THIS DRAWING AND ITS CONTENTS ARE THE PROPERTY OF KINETICO
INCORPORATED. THEY HAVE BEEN LOANED TO YOU FOR A LIMITED TIME AND
PURPOSE, AND MAY NOT BE COPIED OR DUPLICATED WITHOUT THE WRITTEN
PERMISSION OF AN AUTHORIZED EMPLOYEE OF KINETICO INCORPORATED.
ADDITIONALLY, THE PROCESS, METHOD, DESIGN AND DATA CONTAINED HEREIN,
ARE CONSIDERED TO BE THE PROPERTY OF KINETICO INCORPORATED AND MAY
NOT BE DIVULGED TO ANY OTHER PERSON OR COMPANY NOR USED TO
KINETICO'S DISADVANTAGE
REV DESCRIPTION ECO DATE BY APPRVD
THIS DRAWING AND ITS CONTENTS ARE THE PROPERTY OF KINETICO
INCORPORATED. THEY HAVE BEEN LOANED TO YOU FOR A LIMITED TIME AND
PURPOSE, AND MAY NOT BE COPIED OR DUPLICATED WITHOUT THE WRITTEN
PERMISSION OF AN AUTHORIZED EMPLOYEE OF KINETICO INCORPORATED.
ADDITIONALLY, THE PROCESS, METHOD, DESIGN AND DATA CONTAINED HEREIN,
ARE CONSIDERED TO BE THE PROPERTY OF KINETICO INCORPORATED AND MAY
NOT BE DIVULGED TO ANY OTHER PERSON OR COMPANY NOR USED TO
KINETICO'S DISADVANTAGE
REV DESCRIPTION ECO DATE BY APPRVD
Support
bar
THIS DRAWING AND ITS CONTENTS ARE THE PROPERTY OF KINETICO
INCORPORATED. THEY HAVE BEEN LOANED TO YOU FOR A LIMITED TIME AND
PURPOSE, AND MAY NOT BE COPIED OR DUPLICATED WITHOUT THE WRITTEN
PERMISSION OF AN AUTHORIZED EMPLOYEE OF KINETICO INCORPORATED.
ADDITIONALLY, THE PROCESS, METHOD, DESIGN AND DATA CONTAINED HEREIN,
ARE CONSIDERED TO BE THE PROPERTY OF KINETICO INCORPORATED AND MAY
NOT BE DIVULGED TO ANY OTHER PERSON OR COMPANY NOR USED TO
KINETICO'S DISADVANTAGE
REV DESCRIPTION ECO DATE BY APPRVD
Top lid
Front lid
Blanking plate
(see page 10 for use
and installation of
blanking plate)
Kinetico Premier Compact Water Softener Installation Instructions
8
Pre-installation check list
When determining the location of the softener, the following
should be considered:
Inlet
InletOnly
Outlet
Dimensions - h 498mm x w 219mm x d 468mm
2
4
3
1
1
2
3
4
Drain line to air gap with internal trap
Mains water (see WRAS guidance note 09-07-01)
By-pass assembly
Overflow to outside/visable location
www.kinetico.co.uk
9
Installation will vary but should consist of:
a: A pressure regulating valve on the water supply to the softener where the
incoming pressure exceeds 6 bar.
b: A non-return valve on the water main supply to the softener. If using a Kinetico
supplied installation kit, a non-return valve is built into the Inlet Tee.
c: A by-pass assembly which enables the softener to be isolated from the water
supply for maintenance and service. This also maintains the water supply when
the system is disconnected.
d: A drain line from the softener to a waste pipe through an appropriate air gap.
The drain must comply with the water regulations. Please consult WRAS guidance
note 09-07-01 for advice.
e: An overflow run to a suitable outlet that is visible.
a: Means of constructing a by-pass
which consists of:
3 valves,
Tee pieces,
Single check valve
Inlet
Outlet
Inlet Only
Ensure you have the following:
b: Connections for the inlet
and outlet, either by means of
flexible pressure rated hoses or
by direct pipework.
Connections on the softener are
3/4” BSP male threaded fittings.
c: 1/2” ID hose for both the overflow
and the drain.
d: Jubilee clip for the drain line.
Kinetico Premier Compact Water Softener Installation Instructions
10
Locate:
a: Ensure the unit can be
positioned on a flat surface.
b: If sand, silt or turbidity is
present in the water supply,
a separate prefilter should
be installed before the water
softener.
1
Test water pressure:
Test incoming pressure to the
unit. A pressure regulating valve
will be required if the pressure
is above 6 bar.
4
1
2
34
5
6
0bar
Installation instructions
Please note:
The softener can be installed with the
connections on the left or right side of the
cabinet by reversing the components.
Remove cardboard:
Ensure all cardboard is removed
from the inside of the softener.
b: Remove top lid and support bar
(see page 7).
c: Carefully remove the two pieces
of cardboard, then replace the
support bar and lid.
2
Insert the
blanking plate:
Insert the blanking plate into the
outlet which is not in use.
3
THIS DRAWING AND ITS CONTENTS ARE THE PROPERTY OF KINETICO
INCORPORATED. THEY HAVE BEEN LOANED TO YOU FOR A LIMITED TIME AND
PURPOSE, AND MAY NOT BE COPIED OR DUPLICATED WITHOUT THE WRITTEN
PERMISSION OF AN AUTHORIZED EMPLOYEE OF KINETICO INCORPORATED.
ADDITIONALLY, THE PROCESS, METHOD, DESIGN AND DATA CONTAINED HEREIN,
ARE CONSIDERED TO BE THE PROPERTY OF KINETICO INCORPORATED AND MAY
NOT BE DIVULGED TO ANY OTHER PERSON OR COMPANY NOR USED TO
KINETICO'S DISADVANTAGE
REV DESCRIPTION ECO DATE BY APPRVD
Lift up into position, then
carefully drop the plate down
into the slot.
www.kinetico.co.uk
11
Flush:
After all the plumbing has been
completed, but before connecting
to the water softener, flush both
inlet and outlet lines allowing water
to rinse out any debris.
6
Caution:
Do not solder any fitting while connected to the unit adaptors. Care should be
taken during the installation process to ensure solder and flux do not come in
contact with any of the components.
Install:
Plumb pipework as necessary to
accommodate a by-pass assembly.
Please note:
Verify installation complies with regional
water regulations before continuing. Consult
WRAS Guidance Note 09-07-01 for advice.
5
Inlet
Outlet
Inlet Only
Fit in/out adapters:
a: Fit 2 o-rings to each in/out
adaptor then lubricate with the
supplied silicone grease.
b: Connect the inlet/outlet
adapters to the supply and
return hoses remembering to
use the screened washers.
c: Install adapters into control
valve in/out ports, ensuring that
they are fitted into the correct
ports (see flow arrows on valve
for reference).
d: Attach the retaining bracket and
pin to the control valve.
7
Kinetico Premier Compact Water Softener Installation Instructions
12
Review
By-pass assembly:
Ensure the inlet and outlet valves
are closed and that the by-pass
valve is open.
5
Pressure:
Where a pressure regulating valve
has been fitted, ensure it has been
correctly set to 6 bar.
1
Drain line:
Ensure the drain line is securely
attached, has no restrictions or kinks,
uses an airgap and is fully compliant.
2
Overflow:
Ensure the overflow has no kinks, is
securely attached and that water is
able to fall away with gravity.
3
Inlet/Outlet Connections
Ensure the hoses/plumbing are
attached securely, using the
screened washers provided, and
are firmly held in place using the
retaining bracket and pin.
4
Inlet Outlet
Inlet Only
Run drain line:
a: Run a drain line to a
discharge point, checking for
any obstructions or possible
kinks.
FOLLOW REGIONAL WATER
REGULATIONS.
b: Before connecting the drain line
to the unit, slide on the stainless
steel jubilee clip.
c: Push the drain line onto the
barbed fitting and tighten the
jubilee clip securely.
8
Please note:
Drain lines must not run more than
2.4m up or exceed a total of 9m. The
drain line must not be restricted or
kinked.
✗
www.kinetico.co.uk
13
Commissioning instructions
Initiate a backwash:
a: Using a Phillips head screwdriver
push down on the actuator, and
slowly turn CLOCKWISE until the
indicator dot reaches the letter
W in the word “BACKWASH” on
the clear cap.
b: You will hear a rush of water and
air going to the drain.
c: When the cycle has finished
(approx 4 mins), repeat the
procedure, turn the indicator dot
to the next backwash cycle and
allow to finish (approx 4 mins).
3
Pressurise:
With the water to the property restored, slowly open the inlet valve and allow
the softener and pipework to pressurise. Water may run to drain until the unit is
fully pressurised.
1
Fill the brine tank
with water:
Allow the brine tank to fill with
water until the brine valve shuts o.
The water level should be
approximately 25mm over the
grid plate.
TIP:
If the cabinet does not fill
with water please refer to the
“Useful Information” section
(page 16).
2
|
B
R
I
N
E
*
R
I
N
S
E
|
B
A
C
K
W
A
S
H
|
|
B
R
I
N
E
*
R
I
N
S
E
|
B
A
C
K
W
A
S
H
|
Actuator
Indicator
25mm
Water level
Grid plate
Kinetico Premier Compact Water Softener Installation Instructions
14
Add salt:
For convenience, the water softener has been designed to accommodate both
block and tablet/pellet salt.
Block Salt:
To use salt blocks, simply place them in the salt storage compartment with the
indents facing forwards.
Tablet and Pellet Salt:
Simply pour into the salt compartment.
IMPORTANT: Only use salt manufactured for use in water softeners.
Do not use rock or granular salt in your system. They contain impurities which
can interfere with performance and could invalidate the Limited Warranty.
4
THIS DRAWING AND ITS CONTENTS ARE THE PROPERTY OF KINETICO
INCORPORATED. THEY HAVE BEEN LOANED TO YOU FOR A LIMITED TIME AND
PURPOSE, AND MAY NOT BE COPIED OR DUPLICATED WITHOUT THE WRITTEN
PERMISSION OF AN AUTHORIZED EMPLOYEE OF KINETICO INCORPORATED.
ADDITIONALLY, THE PROCESS, METHOD, DESIGN AND DATA CONTAINED HEREIN,
ARE CONSIDERED TO BE THE PROPERTY OF KINETICO INCORPORATED AND MAY
NOT BE DIVULGED TO ANY OTHER PERSON OR COMPANY NOR USED TO
KINETICO'S DISADVANTAGE
REV DESCRIPTION ECO DATE BY APPRVD
www.kinetico.co.uk
15
Fit the lid:
Replace the lids and check
plumbing for any leaks.
The installation is now complete.
6
Put the softener
into service:
a: After the unit has finished the
second backwash and has
pressurised, open the outlet
valve and ensure by-pass
valve is closed.
b: Open a tap in the house to
release trapped air from the
lines rinse out any debris.
5
Inlet
Outlet
Inlet Only
THIS DRAWING AND ITS CONTENTS ARE THE PROPERTY OF KINETICO
INCORPORATED. THEY HAVE BEEN LOANED TO YOU FOR A LIMITED TIME AND
PURPOSE, AND MAY NOT BE COPIED OR DUPLICATED WITHOUT THE WRITTEN
PERMISSION OF AN AUTHORIZED EMPLOYEE OF KINETICO INCORPORATED.
ADDITIONALLY, THE PROCESS, METHOD, DESIGN AND DATA CONTAINED HEREIN,
ARE CONSIDERED TO BE THE PROPERTY OF KINETICO INCORPORATED AND MAY
NOT BE DIVULGED TO ANY OTHER PERSON OR COMPANY NOR USED TO
KINETICO'S DISADVANTAGE
REV DESCRIPTION ECO DATE BY APPRVD
Kinetico Premier Compact Water Softener Installation Instructions
16
Useful information
Should water be present in the salt compartment?
Yes, it is normal to see water at a level of 25mm above the salt grid
(see page 13). If water is not present to this level:
a: Fill softener with water until the level is 25mm over the salt grid, then
conduct a manual regeneration.
b: To manually regenerate using a Phillips head screwdriver push down on
the actuator, and slowly turn CLOCKWISE ONLY until the actuator tab has
advanced the indicator dot to the word “BRINE”.
c: You will hear a rush of water and air going to the drain.
d: When the vessel has finished its cycle (approx 12 mins), repeat the procedure,
advance the indicator dot to the word “BRINE” in the next cycle and allow to
finish (approx 12 mins).
1
|
B
R
I
N
E
*
R
I
N
S
E
|
B
A
C
K
W
A
S
H
|
|
B
R
I
N
E
*
R
I
N
S
E
|
B
A
C
K
W
A
S
H
|
Actuator
Indicator
www.kinetico.co.uk
17
How do I correct the water level if it sits higher than
the recommended 25mm above the salt grid?
Check that the brine valve is correctly held in place by the support bar and is
seated firmly on the base of the cabinet.
2
Kinetico Premier Compact Water Softener Installation Instructions
18
How do I protect the
softener from cold
weather?
If your Kinetico Premier Compact
Water Softener is installed outside
or in an area that is not heated, you
may want to take precautionary
measures to prevent damage to
your unit from freezing. Kinetico
oers cabinets specifically
designed to protect your softener
from freezing temperatures.
Please contact Kinetico for more
information.
NOTE:
Kinetico’s Limited Warranty does
not cover damage caused to your
system due to freezing. If you have
any questions about your Kinetico
Premier Compact Water Softener,
or you suspect that your system isn’t
working properly, please contact
Kinetico.
4
Why am I experiencing
varying levels of
hardness?
The softener will provide soft
water immediately, however, until
mains water has been displaced
from the pipework, storage tanks
and hot water system, you will
experience varying degrees of
hardness.
Depending on your water system
and water usage, this may take a
few weeks to clear.
It is also advisable to check that
the by-pass valve is closed.
3
www.kinetico.co.uk
19
Notes
Kinetico UK Ltd, Bridge House, Park Gate Business Centre, Park Gate, Hants SO31 1FQ
www.kinetico.co.uk
© Kinetico 2016.
1.6/6 #16240
Other manuals for Premier Compact
1
Table of contents
Other Kinetico Water Dispenser manuals
Kinetico
Kinetico 2020c User manual
Kinetico
Kinetico Premier Compact User manual
Kinetico
Kinetico Undersink 7000 User manual
Kinetico
Kinetico MEDDALSOFT 11 User manual
Kinetico
Kinetico gold 15759 User manual
Kinetico
Kinetico Premier Plus User manual
Kinetico
Kinetico Premier Series User manual
Kinetico
Kinetico Powerline PRO User manual
Kinetico
Kinetico Essential Series User manual
Kinetico
Kinetico 2030s User manual
Kinetico
Kinetico Commercial Plus Softener Series User manual
Kinetico
Kinetico 2020c User manual
Kinetico
Kinetico PREMIER XP Series User manual
Kinetico
Kinetico 2020c User manual
Kinetico
Kinetico KUBE 6 User manual
Kinetico
Kinetico S250 OD User manual
Kinetico
Kinetico Aquakinetic Q237 User manual
Kinetico
Kinetico columbia aqua FC-725-ROP-UV User manual
Kinetico
Kinetico Premier Compact HE User manual
Kinetico
Kinetico Ergo 7 User manual
Popular Water Dispenser manuals by other brands
Primo Water
Primo Water 601177 owner's manual
Quooker
Quooker scale control installation guide
EcoWater
EcoWater Comfort Series manual
Elkay
Elkay FLEXI-GUARD EFHA8, 14 1F Series Installation, care & use manual
Crystal Mountain
Crystal Mountain Avalanche user manual
Pentair
Pentair FREEFLO FFCF-EU installation manual
Miele professional
Miele professional PG 8090 operating instructions
Elkay
Elkay FLEXI-GUARD Deluxe EFHA14 Series Installation, care & use manual
Primada
Primada MK-PEK3000 instruction manual
SpectraPure
SpectraPure FLEX 5600S manual
Philips
Philips WP3812 Micro X-Pure user manual
SPM
SPM NINO Operator's manual
