King Canada KC-110C User manual

KING CANADA
10” DRILL PRESS
INSTRUCTION MANUAL
COPYRIGHT ®2002 ALL RIGHTS RESERVED BY KING CANADA TOOLS INC.
MODEL: KC-110C

IMPORTANT INFORMATION
2-YEAR
LIMITED WARRANTY
FOR THIS 10” DRILL PRESS
KING CANADA TOOLS
OFFERS A 2-YEAR LIMITED WARANTY
FOR NON-COMMERCIAL USE.
PROOF OF PURCHASE
Please keep your dated proof of purchase for warranty and servicing purposes.
REPLACEMENT PARTS
Replacement parts for this tool areavailable at our authorized KING CANADA service centers across Canada. For servicing, contact or
return to the retailer where you purchased your product along with your proof of purchase.
LIMITED TOOL WARRANTY
KING CANADA makes every effort to ensure that this product meets high quality and durability standards. KING CANADA warrants
to the original retail consumer a 2-year limited warranty as of the date the product was purchased at retail and that each product is free
from defects in materials. Warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence or accidents, repairs
or alterations and lack of maintenance. KING CANADA shall in no event be liable for death, injuries to persons or property or for
incidental, special or consequential damages arising from the use of our products. To take advantage of this warranty, the product or
part must be returned for examination by the retailer.Shipping and handling charges may apply.If a defect is found, KING CANADA
will either repair or replace the product.

GENERAL SAFETY INSTRUCTIONS
FOR POWER TOOLS
1. KNOW YOUR TOOL
Read and understand the owners manual and labels affixed to
the tool. Learn its application and limitations as well as its
specific potential hazards.
2. GROUND THE TOOL.
This tool is equipped with an approved 3-conductor cord and
a3-prong grounding type plug to fit the proper grounding
type receptacle. The green conductor in the cord is the
grounding wire. NEVER connect the green wire to a live
terminal.
3. KEEP GUARDS IN PLACE.
Keep in good working order, properly adjusted and aligned.
4. REMOVE ADJUSTING KEYS AND WRENCHES.
Form habit of checking to see that keys and adjusting
wrenches are removed from tool before turning it on.
5. KEEP WORK AREA CLEAN.
Cluttered areas and benches invite accidents. Make surethe
floor is clean and not slippery due to wax and sawdust
build-up.
6. AVOID DANGEROUS ENVIRONMENT.
Don’t use power tools in damp or wet locations or expose
them to rain. Keep work area well lit and provide adequate
surrounding work space.
7. KEEP CHILDREN AWAY.
All visitors should be kept a safe distance from work area.
8. MAKE WORKSHOP CHILD-PROOF.
-with padlocks, master switches or by removing starter keys.
9. USE PROPER SPEED.
A tool will do a better and safer job when operated at the
proper speed.
10. USE RIGHT TOOL.
Don’t force the tool or the attachment to do a job for which it
was not designed.
11. WEAR PROPER APPAREL.
Do not wear loose clothing, gloves, neckties or jewelry (rings,
watch) because they could get caught in moving parts. Non-
slip footwear is recommended. Wear protective hair covering
to contain long hair. Roll up long sleeves above the elbows.
12. ALWAYS WEAR SAFETY GLASSES.
Always wear safety glasses (ANSI Z87.1). Everyday
eyeglasses only have impact resistant lenses, thet are NOT
safety glasses. Also use a face or dust mask if cutting operation
is dusty.
13. DON’T OVERREACH.
Keep proper footing and balance at all times.
14. MAINTAIN TOOL WITH CARE.
Keep tools sharp and clean for best and safest performance.
Follow instructions for lubricating and changing accessories.
15. DISCONNECT TOOLS.
Before servicing, when changing accessories or attachments.
16. AVOID ACCIDENTAL STARTING.
Make sure the swich is in the ‘’OFF’’ position before plugging
in.
17. USE RECOMMENDED ACCESSORIES.
Consult the manual for recommended accessories. Follow the
instructions that accompany the accessories. The use of
improper accessories may cause hazards.
18. NEVER STAND ON TOOL.
Serious injury could occur if the tool tips over. Do not store
materials such that it is necessary to stand on the tool to reach
them.
19. CHECK DAMAGED PARTS.
Before further use of the tool, a guard or other parts that are
damaged should be carefully checked to ensure that they will
operate properly and perform their intended function. Check
for alignment of moving parts, breakage of parts, mounting,
and any other conditions that may affect its operation. A guard
or other parts that areda -maged should be properly repaired
or replaced.
20. NEVER LEAVE MACHINE RUNNING
UNATTENDED.
Turn power ‘’OFF’’. Don’t leave any tool running until it comes
to a complete stop.
1. TO AVOID INJURY FROM PARTS BEING THROWN
BY THE SPRING
Follow the instructions exactly as given and shown in
“Adjusting the quill return spring”.
2. USING A DRILL PRESS VISE
When using a drill press vise, always fasten it to the table.
3. NEVER DO “FREEHAND WORK”
Never do any work “Freehand” (Hand holding the workpiece
rather than supporting it on the table) except when you have
polishing to do.
4. SECURE the lock head to the column, table support to
column and table to table support before operating the drill
press.
5. NEVER move the head or table while the drill press is
running.
6. USE THE RECOMMENDED SPINDLE SPEED for the
specific operation and workpiece material. Check the panel
inside the guard cover for drill information. For accessories,
use the instructions provided with the accessories.
7. NEVER climb on the drill press table, it could break or pull
the entire drill press down on you.
SPECIFIC SAFETY INSTRUCTIONS
FOR DRILL PRESS

SPECIFICATIONS
VOLTAGE ............................................................................................................................................................................................................120V
AMPS ....................................................................................................................................................................................................................3.2A
MOTOR R.P.M. ....................................................................................................................................................................................................1700
Hz ..............................................................................................................................................................................................................................60
PHASE ........................................................................................................................................................................................................................1
CHUCK CAPACITY ..........................................................................................................................................................................................1/2”
DISTANCE BETWEEN SPINDLE AXIS AND COLUMN ................................................................................................................................5”
MAX. SPINDLE TRAVEL ..............................................................................................................................................................................2-3/8”
MAX. DISTANCE FROM CHUCK TO THE TABLE..................................................................................................................................9-3/4”
MAX. DISTANCE FROM CHUCK TO THE BASE..................................................................................................................................14-1/4”
RANGE OF SPINDLE SPEEDS (1700 MOTOR R.P.M AT 60Hz) ..............................................................570, 900, 1390, 2050, 3050 R.P.M.

GETTING TO KNOW YOUR DRILL PRESS
LOCATION AND FUNCTION OF CONTROLS
FIGURE 1
1. BELTTENSION LOCK HANDLE...Tightening handles locks the
motor bracket support to maintain the correct belt distance and
tension.
2. FEED HANDLE...moves the chuck up or down. One or two of
the feed handle can be removed if it is necessary (If the
workpiece interferes with the handles).
3. TABLE CRANK HANDLE...Turn clockwise to elevate table.
Support lock must be released before operating crank handle.
4. CHUCK KEY... Used to tighten drill in the chuck and also to
loosen the chuck for drill removal.
5. CHUCK...Holds drill bit or other recommended accessory to
perform desired operations.
6. DEPTH SCALE...shows the depth of the hole being drilled in
inches and millimeters.
7. ON-OFF SWITCH...has a locking feature to prevent
unauthorized and possible hazardous use by children and
others. Just above it you will find the light switch to illuminate
the work table during operations.
8. DEPTH SCALE LOCK... Locks the depth scale at a desired
position.
9. SPRING CAP...Provides means to adjust the quill spring
tension.
10. HEAD LOCKING SET SCREWS... Lock the head to the column.
ALWAYS have them locked in place while you operate the drill
press.
11. BEVEL SCALE...shows the degree in which the table is tilted for
bevel operations. The scale is mounted on the table support.
12. SUPPORT LOCK HANDLE...Tightening locks the table support
to the column. Always have it locked in place while operating
the drill press.
13. TABLE BEVEL LOCK...locks the table in any position from 00-
450.

UNPACKING/TOOLS NEEDED
Your Drill Press is shippec complete in one box. Separate all
loose parts and compare with illustrations on this page to
make sure all parts are accounted for.
Remove protective oil that is applied to the table and
column. Use a grease and spot remover. Apply a coat of
paste wax to the table and column, this will prevent
rusting. Wipe all remaining parts with a clean dry cloth.
TABLE OF LOOSE MACHINE COMPONENTS
A-Table/support assembly ..............................................1
B-Column support assembly ..........................................1
C-Instruction manual........................................................1
D-Box of loose parts..........................................................1
E-Base ..................................................................................1
F- Head assembly ..............................................................1
G-Bag of loose parts..........................................................1
See Fig.2 below for all loose parts.
TOOLS NEEDED
Combination square
8” Ajustable wrench
Medium Phillips screwdriver
WARNING! Toavoid injury from unexpected starting or
electrical shock, never connect the plug to an outlet until all
the assembly instructions are completed.
FIGURE 2
TOOLS NEEDED
Combination square
Medium Phillips screwdriver
8” Ajustable wrench
4- Hex. Bolts
1- Pan Hd. Screw
3mm & 4mm Hex Keys
1- Safety Key
1- Support Lock
Handle
1- Table Crank
1- Belt GuardKnob
3- Feed Handles
1- 1/2” Chuck
1- Chuck Key
1- Worm Elevation
Shaft

ELECTRICAL CONNECTIONS
WARNING
ALL ELECTRICAL CONNECTIONS MUST BE DONE BY A QUALIFIED ELECTRICIAN. FAILURE TO COMPLY MAY RESULT IN
SERIOUS INJURY! ALL ADJUSTMENTS OR REPAIRS MUST BE DONE WITH THE DRILL PRESS DISCONNECTED FROM THE POWER
SOURCE. FAILURE TO COMPLY MAY RESULT IN SERIOUS INJURY!
POWER SUPPLY
WARNING: YOUR DRILL PRESS MUST BE CONNECTED TO A
120V, 15-AMP, BRANCH CIRCUIT AND USE A 15-AMP TIME
DELAY FUSE OR CIRCUIT BREAKER. FAILURE TO CONNECT IN
THIS WAY CAN RESULT IN INJURY FROM SHOCK OR FIRE.
Your drill press must be properly grounded. Not all outlets are
properly grounded. If you are not sure if your outlet is properly
grounded, have it checked by a qualified electrician.
WARNING: IF NOT PROPERLY GROUNDED, THIS DRILL PRESS
CAN CAUSE ELECTRICAL SHOCK, PARTICULARLY WHEN
USED IN DAMP LOCATIONS. TOAVOID SHOCK OR FIRE, IF THE
POWER CORD IS WORN OR DAMAGED IN ANY WAY, HAVE IT
REPLACED IMMEDIATELY.
GROUNDING
This drill press must be grounded. If it should malfunction or
breakdown, grounding provides a path of least resistance for electric
current, to reduce the risk of electric shock. This drill press is
equipped with a cord having an equipment-grounding conductor
and grounding plug. The plug must be plugged into an appropriate
outlet that is properly installed and grounded in accordance with all
local codes and ordinances.
WARNING: TOMAINTAIN PROPER GROUNDING OF YOUR
DRILL PRESS, DO NOT REMOVE OR ALTER THE GROUNDING
PRONG IN ANY MANNER.
120V OPERATION
As received from the factory, your drill press is ready to run for 120V
operation. This drill press is intended for use on a circuit that has an
outlet and a plug which looks like the one illustrated in Fig.3.
WARNING: DO NOT USE A TWO-PRONG ADAPTOR FOR THEY
ARE NOT IN ACCORDANCE WITH LOCAL CODES AND
ORDINANCES. NEVER USE IN CANADA.
EXTENSION CORDS
The use of any extension cord will cause some loss of power. Use the
following table to determine the minimum wire size (A.W.G-American
Wire Gauge) extension cord. Use only 3-wire extension cords which
have 3-prong grounding type plugs and 3-hole receptacles which
accept the tool’s plug.
For circuits that are further away from the electrical circuit box, the wire
size must be increased proportionately in order to deliver ample
voltage to the dust collector motor. Refer to Fig. 4 for wire length and
size.
FIGURE 3
LENGTH OF
CONDUCTOR
0-25 FEET
26-50 FEET
51-100 FEET
WIRE SIZES REQUIRED
(AMERICAN WIRE GAUGE)
120V LINES
NO.16
NO.14
NO.12
FIGURE 4
PROPERLY GROUNDED OUTLET
CURRENT CARRYING
PRONGS
GROUNDING
PRONG
FIGURE 5
120V WIRING DIAGRAM MODEL:KC-110C
MOTOR MOTOR CORD
GREEN
GROUND
BLACK
WHITE
WHITE BLACK
POWER
SWITCH
POWER CORD
GREEN
GROUND
WIRE
CON.

ASSEMBLY INSTRUCTIONS
BASE, COLUMN & TABLE ASSEMBLY
1. Position the base on the floor. Remove the protective covering and
discard.
2. Remove protective sleeve from the column and discard. Place the
column assembly on the base, align the holes in the column support
with the holes in the base.
3. Locate three long bolts from the parts bag.
4. Install a bolt in each hole through the column support and the base
and tighten with the ajustable wrench. Fig.6.
5. Loosen set screw in column collar with 3mm Hex. Key and remove
collar and rack from the column. Fig.7.
6. Find elevation worm gear shaft in the loose parts bag. Insert the
elevation shaft into the table support and extend the shaft through
the opening as far as possible. The crank is to be installed on the
elevation shaft, the set screw is to be aligned with the flat portion of
the shaft. The crank is to be positioned as close to the arm support
as possible, then tighten the set screw. Fig.8.
7. With the long smooth end of the rack pointing upwards, slide rack
down through the large round opening in the table support.
Engage rack in gear mechanism found inside the opening of the
table support. Fig.9.
Rack
Column
Base
FIGURE 6
FIGURE 7
Column
Column
Collar
FIGURE 8
Table
Crank
Table Support
Gear
Mechanism
Rack
FIGURE 9
Elevation Worm
Gear Shaft
Set Screw
Table Support
Table

8. While holding the rack and table support in an engaged position,
slide both down over the column. Slide rack down the column until
the rack is positioned against the lower column support. Fig.10.
9. Replace column collar and position it bevel side down over the
rack. Tighten set screw in collar with 3mm Hex. Key. To let the rack
slide when the table is swung to the left or right around the
column, the collar must sit loosely over the rack and should not be
angled on the column. Only tighten set screw enough to keep the
collar in place, otherwise the collar may break due to excessive
pressure.
10. Check the column collar for proper adjustment. Collar should not
be angled on the column and it should be positioned so rack will
slide freely in collars when the table is rotated 3600around the
column tube. If re-adjusted, only tighten the set screw enough to
keep the collar in place.
NOTE: Toavoid column or collar damage, do not overtighten set
screw.
11. Locate the support lock handle in loose parts bag and tighten by
hand.
12. To minimize crank backlash; tighten the support lock and rotate
elevation worm shaft clockwise with the crank. Loosen the set
screw in the crank and reposition the crank as close to the table
support as possible. Tighten set screw in the crank.
INSTALLING THE HEAD
1. Remove the protective covering from the head assembly.
2. Carefully lift the head above the column and slide it down on the
column as far as it will go. Align the head with the table and the
base.
3. Using a 4mm hex. wrench, tighten the head set screws on the right
side of the head. Fig.13.
ASSEMBLY INSTRUCTIONS
FIGURE 10
Rack
Lower
Column
Support
Support Lock
Handle
FIGURE 11
FIGURE 12
Head
Head Lock
Set Screws
Column
Table Support
Table
FIGURE 13
Table Support
Rack
Column
Collar

ASSEMBLY
Chuck
Sleeve Spindle Nose
FIGURE 15
Chuck Sleeve
Chuck Body
FIGURE 16
Feed handle
Hub
FIGURES 17
Belt Tension
Lock Knob
INSTALLING THE CHUCK FIG.14
1. Locate the chuck in the box of parts.
2.Clean out the tapered hole in the chuck, also clean the spindle nose with a clean
cloth. Make sure there are no foreign particles sticking to the surfaces. The
slightest piece of dirt on the spindle nose or the chuck will prevent the chuck
from seating properly. This will cause the drill to “wobble”.
NOTE: If the tapered hole in the chuck is extremely dirty, use a cleaning solvent on
aclean cloth.
3. Push the chuck up on the spindle nose as far as it will go.
4. Turn the chuck sleeve clockwise and open the chuck jaws completely.
5. Lightly tap the nose of the chuck with a piece of wood to insure the proper
seating of the chuck on the spindle.
REMOVING THE CHUCK FIG.15
1. Open the jaws of the chuck as wide as they will go by turning the chuck sleeve.
2. Carefully tap the chuck with a mallet in one hand while holding the chuck in the
other hand to prevent the chuck from dropping when it is released from the
spindle nose.
INSTALLING THE FEED HANDLES FIG.16
1. Locate the three feed handles among the loose parts.
2. Screw the feed handle tightly into the threaded holes in the hub.
TENSIONING THE BELT FIG’S.17
NOTE: The drill press is shipped with the belt installed, but it should be properly
tensioned before use.
1. Lift the guard from the right side and keep it opened.
2. Release the belt tension lock handle located on the right side of the drill press
head. Pull the right side of the motor towards the front to relieve the spring
tension of the belt. Tighten the belt tension lock handle.
3. Choose the desired speed for your drilling operation, and move the belt to the
indicated position. Refer to the chart on the inside of the belt guard.
4. Loosen the belt tension lock handle and move the right side of the motor
backwards to apply tension to the belt.
5. Tighten the belt tension lock handle.
NOTE: The belt should deflect approximately 1/2” by applying finger pressure at
the mid-point of the belt between the pulleys.
6. Close the belt guard.
7. If the belt slips while drilling, reajust the belt tension.

OPERATING & ADJUSTMENTS
Precision rod
Combination square
Table
Table bevel lock
FIGURE 19
FIGURE 18
Jaws
Chuck
Chuck Key
Safety Key
FIGURE 20
INSTALLING DRILL BITS FIG.18
Insert the drill bit into the chuck far enough to obtain the maximum
gripping of the chuck jaws. The chuck jaws are approximately 1” long.
When using a small drill bit, do not insert it so far that the jaws touch the
flutes (spiral grooves) of the bit.
Make sure the drill bit is centered in the chuck before tightening the
chuck with the key. Tighten the drill bit well, so that it doesn’t slip while
drilling. Turn the chuck key clockwise to tighten counter-clockwise to
loosen.
ADJUSTING THE TABLE SQUARE TO THE HEAD FIG.19
1. Insert a precision round steel rod approximately 3” long into the chuck
and tighten.
2. With the table raised to working height and locked into position, place
acombination squareflat on the table beside the rod.
3. If an adjustment is necessary, loosen the table bevel lock bolt with an
adjustable wrench. This adjustment is located under the table.
4. Align the table squareto the rod by tilting the table.
5. Retighten the table bevel lock bolt.
ON-OFF SWITCH AND LIGHT SWITCH FIG.20
The On-OffSwitch has a locking feature. This feature is intended to help
prevent unauthorized and possible hazardous use by children and
others. This is done by removing the Safety Key when the machine is not
in use. Replace the safety key before an operation.
Just above the On-Off Switch is the Light Switch which turns On and Off
alight bulb which is found inside the head casting.

MAINTENANCE / TROUBLE SHOOTING
LUBRICATION
All of the ball bearings are packed with grease at the factory. They require no further lubrication.
Periodically lubricate the splines (Grooves) in the spindle and the rack (Teeth of the quill). Fig.21.
WARNING! For your own safety, turn the switch “OFF” and remove the plug from the power source
before maintaining or lubricating your drill press.
Frequently blow out any dust that may accumulate inside the motor. After operation, remove chips
or dirt on the machine and apply a coat of furniture-type paste wax to the table and the column, this
will help keep the surfaces clean and free of rust.
PROBLEM
Noisy operation.
Drill bit burns.
Wood splinters on
underside of workpiece.
Workpiece torn loose
from hand.
Drill bit binds in work-
piece.
Excessive drill bit
wobbling.
Quill returns too fast or
too slow.
Chuck will not stay
attached to the spindle.
It falls off when trying
to install it.
PROBABLE CAUSE
1. Incorrect belt tension.
2. Dry spindle.
3. Loose spindle pulley.
4. Loose motor pulley.
1. Incorrect speed.
2. Chips not comming out of hole.
3. Dull drill bit.
4. Feeding too slow.
5. Not lubricated.
1. No “Back-up material” under the work-
piece.
1. Not supported or clamped properly.
1. Workpiece is pinching the drill bit or
there is an excessive feeding pressure.
2. Improper belt tension.
1. Bent drill bit.
2. Worn spindle bearings.
3. Drill bit is not properly installed in the
chuck.
4. Chuck not properly installed.
1. Spring has improper tension.
1. Dirt, grease or oil on the tapered inside
surface of the chuck or on the spindle
tapered surface.
SOLUTION
1. Adjust the tension.
2. Lubricate the spindle.
3. Tighten the retaining nut on the pulley as needed.
4. Tighten the set screws which hold the puleys in place.
1. Change the speed.
2. Retract the drill bit frequently to clear the chips.
3. Resharpen the drill bit.
4. Feeding too fast...allow the drill bit to cut.
5. Lubricate the drill bit with cutting or motor oil.
1. Support the workpiece or clamp it.
1. Support the workpiece or clamp it.
1. Support the workpiece or clamp it.
2. Adjust the tension of the belt.
1. Use a straight drill bit.
2. Replace the bearings.
3. Install drill bit properly.
4. Install chuck properly.
1. Adjust the spring tension.
1. Using a household detergent, clean the tapered
surfaces of the chuck and the spindle to remove the
dirt, grease and oil.
Grooves
Spindle
Teeth of Rack
Chuck
Spindle Assembly
FIGURE 21
PARTS DIAGRAM & PARTS LISTS
Refer to the Parts section of the King Canada web site for the most updated parts diagram and parts list.

USING/ADJUSTING DUAL LASER GUIDE SYSTEM
WARNING! Do not look directly at the laser beams. Do not aim the laser beams at any person or any object other than
your workpiece. Do not deliberately aim the beams into the eye of a person for any length of time. Do not use the laser
guide system aimed at a reflective workpiece, wood or rough coated surfaces are acceptable. This is to avoid the laser beams
from being reflected back at the operator.
Using the dual laser guides system;
Your laser guides are battery operated (2 x AA batteries) and
must be installed inside the laser switch/battery cover (A)
Fig.1. To remove this cover pressure must be applied to the
top and bottom, then you simply pull gently on the cover. Do
not yank the switch off, internal wires are attached to it. When
positioning the batteries, make sure they are positioned with
the correct polarity. Replace the laser/battery cover. Turn the
laser switch on to make sure the dual laser guide system
works.
1) Mark the drilling point on your workpiece.
2) Plug in the drill press and turn the motor on.
3) Switch on the laser guides and align the drilling point with the intersecting point of the laser guides.
4) Secure workpiece to the table with a vise or clamps.
5) Slowly feed the drill bit into the workpiece.
6) Switch off the dual laser guide system on completion of the drilling operation.
Adjusting the dual laser guide system;
If adjustments to the laser guides are necessary,proceed as follows;
1) Loosen set screw (A) Fig.2 (one set screw for each laser) and then slightly turn laser guide (B) Fig.2 in either direction, this
will reposition the laser beams trajectory,adjust the position of the laser guides this way until both beams intersect at the point
where the drill bit touches the workpiece. Retighten set screw (A) after each adjustment.
Caution: Remove the laser guide batteries from the battery compartment if you plan on storing your drill press for more than a
few days. If left in position, the batteries could leak and damage the laser guide assembly. Damage due to leaking batteries is
not covered under warranty.
INSTRUCTIONS FOR DUAL LASER GUIDE SYSTEM
Fig.2
Fig.1

Service Manual / Manuel de Service
10” Drill Press with Dual Laser Guide System
Perceuse À Colonne 10” avec Guide de Laser Double
KC-110C
Revised/Revisé 08/2008

Parts Pricing List / Liste de Prix des Pièces KC-110C
Diag.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
20-1
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
40-1
41
42
43
44
45
46
47
Order # Com.
4001100010
4001100020
4001100030
4001100040
4001100050
4001100060
4001100070
4001100080
4001100090
4001100100
4001100110
4001100120
4001100130
4001100140
4001100150
4001100160
4001100170
KDC-12
KM-003
4001100200
4001100201
4001100210
4001100220
4001100230
4001100240
4001100250
4001100260
4001100270
4001100280
4001100290
4001100300
4001100310
4001100320
4001100330
4001100340
4001100350
4001100360
4001100370
4001100380
4001100401
4001100410
4001100420
4001100430
4001100440
4001100450
4001100460
4001100470
English Description
COLUMN
RACK
COLUMN SUPPORT
BASE
HEX. BOLT
CRANK HANDLE
GEAR SHAFT
HEX. BOLT
SQUARE TABLE
TABLE SUPORT W/ SCALE
TABLE LOCK HANDLE
HELICAL GEAR
ELEVATION WORM GEAR
RACK COLLAR
SET SCREW
BALL BEARING
SPINDLE SHAFT
1/2" CHUCK
CHUCK KEY
QUILL
COMPLETE QUILL ASS'Y
GASKET
RETAINING RING
HEAD
MOTOR
HEX. NUT
WASHER
MOTOR CORD
HEX. NUT
LOCK WASHER
MOTOR BRACKET
MOTOR BRACKET SHAFT
ROLL PIN
KNOB SCREW
SET SCREW
LOCK KNOB
DEPTH STOP W/SCALE
HANDLE KNOB
HANDLE
PINION SHAFT ASS'Y
STOP PIN
WIRE JUMPER
TOOTH WASHER
PAN HD. SCREW
PAN HD SCREW.
SWITCH (2 PRONG)
SAFETY SWITCH KEY
Description Française
COLONNE
CREMAILLIERE
SUPPORT DE LA COLONNE
BASE
BOULON HEXAGONAL
POIGNEE D'ELEVATION
TIGE DE L'ENGRENAGE
BOULON HEXAGONAL
TABLE CARREE
SUPPORT DE TABLE AVEC ECHELLE
POIGNEE DE VERROUILLAGE
ENGRENAGE HELICOIDALE
TIGE D'ELEVATION
COLLIER DE LA COLONNE
VIS SANS TETE
ROULEMENT A BILLES
TIGE DE L'ARBRE
MANDRIN 1/2"
CLÉ DE MANDRIN
QUILLE
QUILLE ASSEMBLEE
JOINT D'ETANCHEITE
ANNEAU DE RETENU
TETE
MOTEUR
ECROU HEXAGONAL
RONDELLE
CORDON DU MOTEUR
ECROU HEXAGONAL
RONDELLE A RESSORT
SUPPORT DU MOTEUR
TIGE SUPPORT DU MOTEUR
GOUPILLE A RESSORT
BOUTON DE SERRAGE
VIS SANS TETE
BOUTON DE VERROUILLAGE
BAGUE D'ARRET AVEC ECHELLE
BOUTON DE LA POIGNEE
POIGNEE
TIGE PIGNON ET MOYAU ASS.
GOUPILLE D'ARRET
LIAISON DE FIL
RONDELLE DENTELEE
VIS
VIS
INTERRUPTEUR (2 PATTES)
CLE DE SECURITE D'INTERRUPTEUR
Price/Prix
$34.33
$22.60
$16.73
$44.45
$1.78
$12.25
$3.28
$2.13
$38.93
$27.43
$6.15
$11.44
$13.63
$8.80
$1.55
$11.10
$25.24
-
-
$45.60
$80.33
$3.97
$1.55
$96.54
$102.35
$1.61
$1.50
$12.25
$1.50
$1.55
$12.48
$4.89
$1.78
$3.28
$1.90
$3.05
$9.60
$3.97
$9.03
$24.90
$2.70
$2.70
$1.67
$1.55
$1.55
$7.65
$3.34
Pricing subject to change without prior notice. / Prix sujet à changement sans préavis.
Qty./Qté.
1
1
1
1
4
1
1
1
1
1
1
1
1
1
2
2
1
1
1
1
1
1
1
1
1
4
8
1
2
2
1
2
1
2
3
1
1
3
3
1
1
2
2
2
2
1
1

Parts Pricing List / Liste de Prix des Pièces KC-110C
Diag.
48
49
50
51
52
53
54-1
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
80
81
82
83
84
85
90
92
93-1
94
95
Order # Com.
4001100480
4001100490
4001100500
4001100510
4001100520
4001100530
4001100541
4001100570
4001100580
4001100590
4001100600
4001100610
4001100620
4001100630
4001100640
4001100650
4001100660
4001100670
4001100680
4001100690
4001100700
4001100710
4001100720
4001100730
4001100740
4001100750
4001100760
4001100770
4001100780
4001100800
4001100810
4001100820
4001100830
4001100840
4001100850
4001100900
4001100920
4001100931
4001100940
4001100950
400110MBIL
English Description
SELF TAPPING SCREW
SWITCH PLATE
SWITCH BOX
SPECIAL SCREW
SPRING SEAT
HEX. NUT
SPRING CAP ASS'Y
POWER CORD
1/8" HEX. KEY
HEX. KEY (4MM)
COVER KNOB
MOTOR PULLEY
PULLEY GUARD
SCREW
RUBBER BUSHING
RETAINING RING
BALL BEARING
BEARING SPACER
PULLEY INSERT
SPINDLE PULLEY
RETAINING RING
V-BELT (K-31)
CORD CLAMP
SCREW
FOAM WASHER
SET SCREW
HEX. NUT
LIGHT SWITCH (2 PRONG)
LIGHT CONNECTION WIRE
CHUCK KEY HOLDER
LIGHT FIXTURE
SCREW
HEX. NUT
SUPPORT PLATE
SCREW
NEW LASER HEAD
PAN HD. SCREW
LASER BOX & SWITCH ASS'Y
SET SCREW
LASER GUIDE
BILINGUAL MANUAL KC-110C
Description Française
VIS AUTOTARAUDEUSE
PLAQUE DE L'INTERRUPTEUR
BOITIER DE L'INTERRUPTEUR
VIS SPECIALE
SIEGE DU RESSORT
ECROU HEXAGONAL
RESSORT ET COUVERCLE ASS.
CORDON D'ALIMENTATION
CLE HEX. 1/8"
CLE HEX. (4MM)
BOUTON DU COUVERCLE
POULIE DU MOTEUR
PROTEGE-POULIE
VIS
BAGUE EN CAOUTCHOUC
ANNEAU DE RETENU
ROULEMENT A BILLES
ESPACEUR DE ROULEMENT
TIGE DE LA POULIE
POULIE DE L'ARBRE
ANNEAU DE RETENU
COURROIE EN V (K-31)
ATTACHE-FIL
VIS
RONDELLE EN MOUSSE
VIS SANS TETE
ECROU HEXAGONAL
INTERRUPTEUR (2 PATTES)
FIL ELECTRIQUE LUMIERE
PORTE-CLE DU MANDRIN
DOUILLE POUR AMPOULE
VIS
ECROU HEXAGONAL
PLAQUE DE SUPPORT
VIS
NOUVELLE TETE POUR LASER
VIS
BOITIER & INTERR. DU LASER ASS.
VIS SANS TETE
GUIDE AU LASER
MANUEL BILINGUE KC-110C
Price/Prix
$1.55
$3.28
$7.65
$3.16
$3.62
$1.78
$11.21
$13.74
$2.93
$2.70
$2.59
$22.71
$36.40
$1.55
$2.13
$2.24
$12.59
$4.54
$13.28
$21.10
$2.13
$10.18
$1.67
$1.55
$1.55
$1.61
$1.55
$10.06
$3.05
$3.05
$5.69
$1.78
$1.55
$2.24
$1.55
$96.54
$1.55
$17.08
$1.55
$17.08
$15.00
Pricing subject to change without prior notice. / Prix sujet à changement sans préavis.
Qty./Qté.
3
1
1
1
1
3
1
1
1
1
1
1
1
4
1
1
2
1
1
1
1
1
3
3
4
1
1
1
1
1
1
1
1
1
1
1
2
1
2
2
1