KING CANOPY C61013PC User manual

10’X13’ UNIVERSAL 6 LEG
ITEM #: C61013PC
Dimensions:
10ft. 8in. Wide x 13ft. Deep x 6ft. 8in. Side Height / 9ft. 9in. Center Height
WARNING:
Keep all ame and heat sources
away from this tent fabric. Meets
the ammability requirements of
CPAI-84 It is not re proof
The fabric will burn if left in
continuous contact with any
ame source.
Distributed by: PIC America, LTD.
1730 Five Points Lane • Fuquay-Varina, NC 27526
1-800-800-6296 • www.kingcanopy.com

6X6PC 12 pc 78” Powder Coated Pipe
5X8PC 6 pc 68” Powder Coated Pipe
3WPC 6 pc 3-way Connectors
4WPC 3 pc 4-way Connectors
BALL50W 50 pc Elastic Ball Straps
PFOOT 6 pc Plastic Foot Pads
TDS1013 1 pc White Drawstring Cover
CCLIP 4 pc Curtain Clips
6X6PC
5X8PC 3WPC
4WPC
PFOOT
CCLIP
TDS1013
BALLW
PARTS

FRAME ASSEMBLY
1) Start by laying out all of the parts and pieces to your King Canopy. Please refer to the
parts list to ensure that your kit is complete. When all the parts have been accounted
for, begin to layout the perimeter of your frame according to the photo above (6X6PC &
5X8PC). Each 3-way tting (3WPC) should be placed at all four corners and two end peaks.
The 4-Way ttings (4WPC) are placed at the center leg and roof sections.
5X8PC 5X8PC
5X8PC 5X8PC
5X8PC 5X8PC
3WPC
3WPC 3WPC
3WPC 3WPC 3WPC
6X6PC
6X6PC
6X6PC
6X6PC
6X6PC
6X6PC
4WPC
4WPC 4WPC
2) Now that all the pipe and ttings are
laid out as displayed in the photo, begin
to connect the center pipe and ttings.
Start assembly by working from one end
to the other, connecting the center ridge
pipe into the 3-Way (3WPC) and 4-Way
(4WPC) ttings.
3) Once the center frame work is fully
connected start assembling the left and
right sections of the frame. Starting at
one end, begin to connect the 5x8PC
pipe to the assembled center ridge. Next
connect thecorner3-Way&4-Way ttings
to the perimeter 6X6PC pipe.
6X6PC
6X6PC
6X6PC
6X6PC

4) Once one side is complete, move
to opposite sides of the unassembled
frame lifting the frame and connecting
the remaining 5X8PC pipe. Continue
previous steps until all pipe and ttings
are connected.
5) Now that the roof frame work is
complete you can begin to attach the
drawstring style cover. Start by laying out
the cover to determine which way it is
folded the length or width or the frame.
6) Grab each end and drape the cover
over the frame centering the cover to
the roof frame work.
7) Starting at opposite corners, attach
the cover with the elastic ball straps by
inserting the elastic cord of the ball strap
underneath the cover and through the
grommet. Then pull taught until the ball
stops.
FRAME & ATTACHING COVER
Width
Length

8) Wrap the cord around the pole and
secure around the ball.
9) Be sure all four corners are attached
before attaching the remaining ball
straps.
10) Continue attaching straps from left
to right in a zig zag pattern starting at
the two center peaks.
11) Next continue attaching the straps
down each side and end. Make sure the
cover stays centered on the frame.
ATTACHING COVER

12) Now that all the ball straps are
attached. Insert the pipe into each plastic
foot pad and begin to attach the legs
to the frame. Place each leg next to the
three and four way ttings.
13) Slide a c-clip on to each corner leg
before inserting them into the 3-way
ttings.
14) Starting with the two outside legs
grab the base of the 3-way corner tting.
Lift the frame and insert the leg into the
open 3-Way tting. Next insert the center
leg.
15) Repeat step on other side until the
entire unit is standing upright.
LEG ASSEMBLY
Insert First
Insert First
Insert Second

COVER ADJUSTMENT
16) Pull each drawstring cord down
evenly and hook onto the c-clip at each
corner leg. Repeat step at the other end
of the canopy. Use remaining ball straps
to secure the valances to the
17) Use the remaining ball straps to
secure the valances to the legs.
Pull
Cord
Down
&
Hook
This canopy is designed for use as a temporary structure. After assembly, the canopy
MUSTBE securelyanchoredto thegroundto preventdamage from winds. Your canopy
will act like a kite in the wind if not properly and securely anchored to the ground. Severe
winds will cause the frame to twist and unanchored legs will fall, thereby collapsing the
canopy. If severe winds are expected, you must remove the cover from the frame to
prevent damage. Please follow the anchoring instructions found in the optional anchor
kit available for purchase separately.

We are condent that you will be completely satised with your King Canopy unit. Please take a moment
to read the very important information below, and call us with any questions you may have.
King Canopy/PIC America, LTD. has no control over wind, snow, ice, rain or any other weather condition and
we are in no way responsible for any damage caused by the canopy or to the canopy. We suggest you contact
your insurance carrier just as you would for any other outside structure.
OTHER PRECAUTIONS WHICH MUST BE FOLLOWED:
Keep all ame and heat sources away from this tent fabric. The tent fabric will burn if left in continuous
contact with any ame source.
DO NOT cook underneath or near canopy.
DO NOT store or use ammable liquids underneath or near canopy.
DO NOT ignite or store reworks underneath or near canopy.
DO NOT use bleach to clean cover.
DO NOT dry clean cover.
DO NOT wash cover in washing machine or dry in dryer. Hand wash with mild soap and water only.
DO NOT allow rain water, snow or ice to accumulate on top of cover.
DO NOT hang or suspend anything from the frame, grommets, truss system or ball straps of the unit.
REMOVE canopy cover before a storm, or disassemble entire canopy unit if possible.
REMOVE rain water, snow and ice from canopy cover.
This is a temporary structure and is not recommended for use as a permanent structure.
IMPORTANT NOTICE: PLEASE READ CAREFULLY

Defective Parts
We try our best to eliminate any defective parts that are shipped with our products. If, however, you should nd
a defective part, we will replace – free of charge – any part which is defective. You will need to provide proof
of purchase showing date of purchase and provide us with detailed description of the defective component.
Your replacement will be shipped by ground shipping, freight prepaid. Next day or express shipping will
require freight collect and paid for by you, the consumer. Damages from improper anchoring, strong winds,
snow, ice or rain are not considered defects.
Improper Anchoring, Strong Winds, Rain Snow, or Ice
King Canopy/PIC America, LTD. does not guarantee these canopies under strong weather conditions. These
canopies are designed to protect against damages caused by sun, rain, tree sap, birds, etc. They are not designed
to hold roof loads that accompany snow, ice or heavy rains. If your canopy is not anchored securely, it can be
lifted by the wind and will y away. If your canopy takes ight, we are not responsible for any replacement. If
you know strong weather is predicted, remove the cover or take down the canopy unit completely. The cover
is designed to be quickly and easily removed.
Warranty
All components of this canopy feature a 1-year limited warranty and are warranted to be free from defects in
material and workmanship for a period of 1-year. You must complete and return the enclosed warranty card
promptly after purchase. Please retain your proof of purchase receipt; you will be asked to provide this receipt
in order to obtain warranty service.
Non-Warranty Replacement Parts
If after expiration of the warranty period, you require replacement parts please contact us at 1-800-800-6296.
We stock replacement parts and make them available to you at discounted prices. Our customer service
department will be pleased to assist you in any way possible.
Certain regions of the country are extremely hard on covers of any kind. Normal wear and tear is not covered
under the warranty, and should be expected.
In order to receive a discounted or free replacement part, you may be asked to return the part, freight prepaid,
to our warehouse for inspection before we will send a replacement. You must, in all cases, provide a copy of
your receipt showing the date of purchase, model number and price.
For missing parts, replacement parts or any questions:
Please Call 8:00am – 5:00pm EST, Monday – Friday
1-800-800-6296 or 1-919-552-2977
Or you can fax us at: 1-919-552-5069
Replacement parts and customer service is also available through our website.
Please visit us at www.kingcanopy.com
WARRANTY INFORMATION