Kingray MHU24F/FS User manual

STANDARD COMMUNICATIONS CONTRACT WARRANTY AGAINST DEFECTS
This warranty against defects is given by Standard
Communications Pty Ltd ACN 000 346 814 (We, us, our
or GME). Our contact details are set out in clause 2.7.This
warranty statement only applies to products purchased
in Australia. Please contact your local GME distributor for
products sold outside of Australia. Local distributor details
at www.gme.net.au/export.
1. Consumer guarantees
1.1 Our goods come with guarantees that cannot be
excluded under the Australian Consumer Law. You
are entitled to a replacement or refund for a major
failure and for compensation for any other reasonably
foreseeable loss or damage.You are also entitled to
have the goods repaired or replaced if the goods fail
to be of acceptable quality and the failure does not
amount to a major failure.
1.2 To the extent we are able, we exclude all other
conditions, warranties and obligations which would
otherwise be implied.
stcefedtsniagaytnarraW.2
2.1 This warranty is in addition to and does not limit,
exclude or restrict your rights under the Competition
and Consumer Act 2010 (Australia) or any other
mandatory protection laws that may apply.
2.2 We warrant our goods to be free from defects in
materials and workmanship for the warranty period
(see warranty table) from the date of original sale (or
another period we agree to in writing). Subject to our
obligations under clause 1.2, we will at our option,
either repair or replace goods which we are satisfied
are defective.We warrant any replacement parts for
the remainder of the period of warranty for the goods
into which they are incorporated.
2.3 To the extent permitted by law, our sole liability for
breach of a condition, warranty or other obligation
implied by law is limited
(a) in the case of goods we supply, to any one of the
following as we decide -
(i) the replacement of the goods or the supply of
equivalent goods;
(ii) the repair of the goods;
(iii) the cost of repairing the goods or of acquiring
equivalent goods;
(b) in the case of services we supply, to any one of the
following as we decide –
(i) the supplying of the services again;
(ii) the cost of having the services supplied again.
2.4 For repairs outside the warranty period, we warrant
our repairs to be free from defects in materials and
workmanship for three months from the date of the
original repair. We agree to re-repair or replace (at
our option) any materials or workmanship which we
are satisfied are defective.
2.5 We warrant that we will perform services with
reasonable care and skill and agree to investigate any
complaint regarding our services made in good faith.
If we are satisfied that the complaint is justified, and
as our sole liability to you under this warranty (to the
extent permitted at law), we agree to supply those
services again at no extra charge
to you.
2.6 To make a warranty claim you must before the end
of the applicable warranty period (see warranty
table), at your own cost, return the goods you allege
are defective, provide written details of the defect,
and give us an original or copy of the sales invoice
or some other evidence showing details of the
transaction.
2.7 Send your claim to:
Standard Communications Pty Ltd.
PO Box 96, Winson Hills, NSW 2153.
Tel: [phone], Fax: (02)
8867 6199
Email: [email protected]
2.8 If we determine that your goods are defective, we will
pay for the cost of returning the repaired or replaced
goods to you, and reimburse you for your reasonable
expenses of sending your warranty claim to us.
3. What this warranty does not cover
3.1 This warranty will not apply in relation to:
(a) goods modified or altered in any way;
(b) defects and damage caused by use with non
Standard Communications products;
(c) repairs performed other than by our authorised
representative;
(d) defects or damage resulting from misuse, accident,
impact or neglect;
(e) goods improperly installed or used in a manner
contrary to the relevant instruction manual; or
(f) goods where the serial number has been removed
or made illegal.
4. Warranty period
4.1 We provide the following warranty on GME and
Kingray products. No repair or replacement during the
warranty period will renew or extend the warranty
period past the period from original date of purchase.
Drawing No: 42631-3 Part No: 310295
MHU24F/FS, MHW24F/FS
FULLY SHIELDED AND NON SHIELDED
F TYPE MASTHEAD AMPLIFIERS
INSTALLATION MANUAL
Specialists in TV signal amplification
Optimised for both digital and analogue
TV signal amplification.
sirefiilpmadaehtsamA•
designed to amplify low
signal levels for both
analogue and digital
applications.
dluohsniagrefiilpmaehT•
be selected to suit each
individual environment.
Mount with polypropylene
securing strap on to mast
or mount to a wall with the
four pre-drilled holes
Best Mounting location for
masthead unit is on mast
300 mm to 1 metre below
antenna
LED
Ensure weatherproof strips
remain in place
Thank you for selecting an Australian designed
and built F Type masthead amplifier.
For
maximum
VHF/UHF
gain turn
control
clockwise
42631-3_MHU-W24F-FS.indd 1-3 27/08/13 2:09 PM

2
SPECIFICATIONS
INSTAllATION
All these models are designed for combined or separate antenna inputs.
Combined Input Separate Input
UHF/VHF
IN UHF/VHF
OUT
UHF
VHF
GAIN
UHF/VHF
IN UHF/VHF
OUT
VHF
IN
UHF
VHF
GAIN
Leave the
link on for a
combined
antenna
or
Remove for
a separate
antenna
Frequency Range VHF: 44 - 230 MHz
UHF: 520 - 820 MHz
Gain Control
Range
VHF: Tilt Control 7 dB - 4 dB
UHF: 10 dB
Supply Voltage PSK08/F: 17.5 V AC and
PSK06/F: 14 V DC @ 60 mA
Max Gain VHF: 12 - 15 dB
(W Models ONLY)
VHF: -2 dB U Models
UHF: 24 dB
MHW24F/FS ONLY
Pager Filter -25 dB @ 148 MHz and
158 MHz
Noise Figure VHF: < 3.5 dB
UHF: < 2.1 dB
Output Figure 108 dB
DIN45004B @ (-60 dB IMR)
FM Filter -25 dB @ 88 - 108 MHz
INSTAllATION
3
The FM and pager filter are located in the
MHW models only.
The -25 dB Band Stop FM Filter may be disabled by
simply removing the shorting link and placing it on
the specified terminals.The FM trap must be in the
out position to view television channel 3, 4 or 5.
The pager filter is set to notch both 148 MHz for
Australia and 158 MHz for New Zealand.
4
INSTAllATION CONTINUED
Power Through Option: MHU Models only. The MHU Models can be used as an in-line amplifier
for boosting UHF television signals on long cable
runs.To power pass, connect link to socket labelled
‘Power Pass’.
PSK06F/08F PSK06/08
TO
TELEVISION
▼
TO AMPLIFIER
▼
17.5VOLT DC
INPUT
POWERING IN-LINE OPTIONS
POWER PASS LINK (MHU24 SERIES ONLY)
The MHU24 series has the ability to pass power through to the input.This is activated by attaching the
shorting link provided to both pins of the ‘Power Pass Link.’ Both models can pivot to easily access connectors
Bare back cable with a cable stripper or stanley knife
Slide on F connector and crimp or use a twist on connector
Shielded models can have lid inserted into plastic
outer cover whilst installing
1. Check there is no earth braid touching the centre
conductor on the coaxial cable.
2. Is there more than one outlet? Check the
splitter box, the power supply must be connected
to the coaxial outlet that feeds the AC/DC leg of
the splitter box to pass power to the head unit.
(Check if LED is on).
3. Is there now too much signal causing an
overload effect to the VCR? Try turning down
the gain controls on the masthead unit, or select a
lower gain amplifier.
If there is a white line moving through the
picture: Try a PSK06 14 V DC power supply.
TECHNICAl ADVICE
42631-3_MHU-W24F-FS.indd 4-6 27/08/13 2:09 PM