Kingray SAT40S User manual

Optimised for digital TV signal amplification.
Thank you for selecting an Australian
designed and built amplifier.
The SAT40S and SAT25S are satellite
distribution amplifiers for use in SMATV
multiple dwelling applications. They feature
high output with adjustable gain and
equalisation control. The amplifier is designed
to be powered by an 18 volt DC power supply
(see Fig .1).
SAT40S, SAT25S
Satellite 950-3000 MHz
Distribution Amplifier
CAUTION: This amplifier contains
devices that are sensitive to
Electrostatic Discharge (ESD).
WARNING: Do not connect power directly into
the input sockets otherwise damage will occur.
INSTALLATION MANUAL
Specialists in TV signal amplification
STANDARD COMMUNICATIONS CONTRACT WARRANTY AGAINST DEFECTS
This warranty against defects is given by Standard
Communications Pty Ltd ACN 000 346 814 (We, us,
our or GME). Our contact details are set out in clause
2.7. This warranty statement only applies to products
purchased in Australia. Please contact your local GME
distributor for products sold outside of Australia. Local
distributor details at www.gme.net.au/export.
1. Consumer guarantees
1.1 Our goods come with guarantees that cannot be
excluded under the Australian Consumer Law.
You are entitled to a replacement or refund for
a major failure and for compensation for any
other reasonably foreseeable loss or damage.
You are also entitled to have the goods repaired
or replaced if the goods fail to be of acceptable
quality and the failure does not amount to a major
failure.
1.2 To the extent we are able, we exclude all other
conditions, warranties and obligations which
would otherwise be implied.
2. Warranty against defects
2.1 This warranty is in addition to and does not
limit, exclude or restrict your rights under the
Competition and Consumer Act 2010 (Australia)
or any other mandatory protection laws that may
apply.
2.2 We warrant our goods to be free from defects
in materials and workmanship for the warranty
period (see warranty table) from the date of
original sale (or another period we agree to in
writing). Subject to our obligations under clause
1.2, we will at our option, either repair or replace
goods which we are satisfied are defective.We
warrant any replacement parts for the remainder
of the period of warranty for the goods into which
they are incorporated.
2.3 To the extent permitted by law, our sole liability for
breach of a condition, warranty or other obligation
implied by law is limited
(a) in the case of goods we supply, to any one of
the following as we decide -
(i) the replacement of the goods or the supply of
equivalent goods;
(ii) the repair of the goods;
(iii) the cost of repairing the goods or of acquiring
equivalent goods;
(b) in the case of services we supply, to any one of
the following as we decide –
(i) the supplying of the services again;
(ii) the cost of having the services supplied again.
2.4 For repairs outside the warranty period, we
warrant our repairs to be free from defects in
materials and workmanship for three months
from the date of the original repair. We agree to
re-repair or replace (at our option) any materials or
workmanship which we are satisfied are defective.
2.5 We warrant that we will perform services with
reasonable care and skill and agree to investigate
any complaint regarding our services made in
good faith. If we are satisfied that the complaint
is justified, and as our sole liability to you under
this warranty (to the extent permitted at law), we
agree to supply those services again at no extra
charge to you.
2.6 To make a warranty claim you must before the end
of the applicable warranty period (see warranty
table), at your own cost, return the goods you
allege are defective, provide written details of the
defect, and give us an original or copy of the sales
invoice or some other evidence showing details of
the transaction.
2.7 Send your claim to:
Standard Communications Pty Ltd.
17 Gibbon Rd, Winston Hills, NSW 2153 Australia.
Tel: [phone], Fax: (02)
8867 6199
Email: [e-mail]
2.8 If we determine that your goods are defective, we
will pay for the cost of returning the repaired or
replaced goods to you, and reimburse you for your
reasonable expenses of sending your warranty
claim to us.
3. What this warranty does not cover
3.1 This warranty will not apply in relation to:
(a) goods modified or altered in any way;
(b) defects and damage caused by use with non
Standard Communications products;
(c) repairs performed other than by our authorised
representative;
(d) defects or damage resulting from misuse,
accident, impact or neglect;
(e) goods improperly installed or used in a manner
contrary to the relevant instruction manual; or
(f) goods where the serial number has been
removed or made illegible.
4. Warranty period
4.1 We provide the following warranty on GME and
Kingray products. No repair or replacement during
the warranty period will renew or extend the
warranty period past the period from original date
of purchase.
Product Type Warranty Period
Satellite Distribution Amplifier 3 years
Figure 1. (Lid removed)
Satellite
Input
Selector
Switch
18V, 12V
or 0V
0-10dB (SAT25S)
0-20dB (SAT40S)
Gain Control
950-3000 MHz
Power LED
Electrostatic
Warning
18V DC
Input
0-15dB
Equalisation
Controls
950-2400 MHz
Satellite
Output

Drawing No: 49638-2 Part No: 311060
INSTALLATION
The SAT40S or the SAT25S is intended for
indoor use.
Mount so there is free circulation of air around
the amplifier and sufficient space for the cable
connections.
Cable connections
The input/output cable connectors are ‘F’ Type.
Powering options
LNB powering: A LNB can be powered by
the SAT40S or SAT25S from each input socket.
Simply select 18 volts, 12 volts or 0 volts using
the selector switches.
Local powering: The PSK18S plugs directly
into the DC power socket located between the
two satellite output sockets (Fig. 1).
Line powering: Can be achieved using a
PSK18F and supplying 18 volts to the output
terminal (Fig. 2 ).
Line powering can also be achieved from the
input by using a PSK18F to inject voltage into
the input lead, then installing a PIK2000 in
line with the input socket and connecting the
DC plug on the PIK2000 to the DC Socket on
the amplifier (Fig. 3).
SPECIFICATIONS
PARAMETER SPECIFICATION NOTE
MODEL SAT40S SAT25S
Frequency Range 950-3000 MHz 950-3000 MHz
Gain 40dB (Nominal) 25dB (Nominal) 950-3000 MHz
Flatness ± 2dB ± 2dB 950-3000 MHz
Noise Figure < 10dB < 10dB 950-3000 MHz
Return Loss > 10dB > 10dB 950-3000 MHz
Gain Control Range 0-20dB 0-7dB 950-3000 MHz
Equalisation Range 15dB 15dB 950-2400 MHz
Output Level 122dBµV 112dBµV - 30 dB IMR3
Supply Voltage 18V DC 18V DC
Current Consumption 260-410 mA* 110-260 mA*
POWERING FEATURES
Option 1 Locally - PSK18S plug pack
Option 2 Remotely - PSK18F to the output
LNB Via switches
Radiation < 20 dBpw
Operating Temperature -10ºC to 50ºC
Dimensions 195 x 55 x 35 mm
Weight 250 grams
Connectors ‘F’ Type
* Depending on current drain by LNBs
All values are typical unless otherwise specified.
Adjustments
Gain: Set the output level according to the
network calculations.
Adjustment range is 0-20dB (SAT40S)
0-10dB (SAT25S)
Equalisation: Set the equalisation according
to the network calculations.
Adjustment range 0-15dB (950-2400 MHz).
A division of Standard Communications Pty Ltd.
Head Office: PO Box 96, Winston Hills, NSW 2153, Australia.
New Zealand: PO Box 58446 Botany,Auckland, 2163,
NZ. T: [phone].
All international enquiries email: [e-mail]
Note: When using the SAT25S with
the Kingray KMS-F1 as a launch
amplifier, do not exceed 102dBµV
output level.
DVB-S2 MPEG-4
YEAR
WARRANTY
Figure 2. (Lid removed)
Figure 3. (Lid removed)
PSK18F
Satellite Signal IN
PSK18F
PIK2000