KMART 42909224 User manual

1
2
5
4
3
7
8
9
10
11
6
6
6
6
Assembly Instructions
1
1PC 21PC 31PC
4
1PC 51PC 64PCS
7
1PC 8
1PC 9 1PC
10
1PC 11 1PC
Hardware list
10PCS
A
10PCS
B
12PCS
C
11PCS
D
4PCS
E
8PCS
F
8PCS
G
8PCS
H
1PC
1PC
1PC
1PC
2PCS
2PCS
I
J
K
L
M
N
42909224 HALL TABLE WHITE
12
12
1PC
6X35mm
15x9mm
6x30mm
4X35mm
Glide
M6X45mm
Flat Washer
Spring Washer
Allen Key
Flat Washer
Paper Cover
Pan Screw
Plastic Anchor
Anti Tip Strap
CARE INSTRUCTIONS:
WARNING:
DO NOT STAND OR SIT ON THE PRODUCT. DO NOT USE THE PRODUCT AS A STEP LADDER. DO NOT USE THE PRODUCT UNLESS ALL BOLTS AND SCREWS ARE FIRMLY
SECURED. FAILURE TO FOLLOW THESE WARNING COULD RESULT IN SERIOUS INJURY. MAXIMUM SAFE LOAD: 10KGS FOR TOP PANEL,3KGS FOR DRAWER.
WIPE CLEAN WITH SOFT DAMP CLOTH. DO NOT USE SCOURERS, ABRASIVES OR CHEMICAL SOLVENTS. STORE IN A DRY PLACE AND KEEP AWAY FROM DIRECT WATER
AND SUNLIGHT. FOR INDOOR AND DOMESTIC USE.

STEP 1
STEP 2
STEP 3
STEP 4
1
A
A
A
A
1
2
3
C
B
1
5
4
C
C
C
C
D
D
D
A
A
C
C
C
C
N
N
C
12
D
D
D
C
C
Fix part A onto board 1 into the corresponding position
as per diagram. Put board 5 onto board 2 & 3 into the corresponding position as per diagram.
Attach board 2 & 3 &12 onto board 1 with part B & C.
Attach board 4 onto board 2 & 3 &12 with part C & D.
2
3
2
3
12
Put part N onto screw holes of board 2 into the
corresponding position as per diagram.

STEP 5
STEP 6
STEP 7
STEP 8
FH
G
I
E
6
6
6
6
Attach leg 6 onto board 4 with part G,H,F & I.
Peel off self-adhesive tape of Glide E, stick them on the bottom of each leg .
Fix part A onto board 11 into the corresponding position as per diagram.
Attach board 7 & 9 onto board 11 with part B.
Attach Anti Tip Strap J onto board 4 with part L &M into the corresponding position as per diagram.
4
M
J
L
11
11
B
7
9
B
B
B
10
Put board 10 onto board 7 & 9 into the corresponding position as per diagram.
7
9
A
A
A
A

STEP 9
STEP 10
8
D
D
D
D
7
9
Attach board 8 onto board 7 & 9 with part D.
Attach the drawer onto Step 6 and then adjust drawer runner into corresponding position
as per diagram.
ATTENTION:
DO NOT TIGHTEN THE SCREWS FULLY DURING ASSEMBLY.
FULLY TIGHTEN SCREWS AFTER THE FINAL ASSEMBLY STEPS.
DO NOT PUT HOT ITEMS SUCH AS COFFEE CUPS DIRECTLY ON THE SURFACE OF PRODUCT!
OK
Finish the assembly.
D
Predrill the hole at wall, insert part K into hole,
attach Anti Tip Strap J with part D & M into the
corresponding position as per diagram.
KM
J
It is strongly recommended that this product is permanently fixed to the wall. Please seek
professional advice if you are in doubt of what fixing device to use.
Regularly check that anchors are securely maintained.
Check any electrical wires or plumbing inside the wall before drilling any holes
(if you are unsure please seek professional advice from a qualified tradesperson).
CAUTION: for your safety when attaching the anchor fixings, please note the following:
STEP 11