KMART OAK LOOK STORAGE BOOKSHELF User manual

13
2
Hardware List
11PC 21PC 3
1PC 56
1PC 81PC
7
42PCS
a4pcs
b
c
d
e
28pcs
4pcs
2pcs
4pcs
f2pcs
i24pcs
91PC
1PC 11 1PC
10 12 1PC
1PC
1PC
10
9
11
12
1
3
2
7
6
6
8
4
5
g17pcs
h4pcs
j2pcs
k1pc
l
m
n
1pc
1pc
4pcs
42839903 OAK LOOK STORAGE BOOKSHELF
screw
doorstop
pad&screw
iron dowel pin
nail
pad
wall fixing
stopper
osticker 8pcs

9
1
0
f
f
1
6
6
7
8
c
c
c
c
c
cc
c
g
g
g
g
4
5
c
cc
c
c
cc
c
g
gg
g
g
g
g
g
3
1
9
10
a
a
a
a
b
b
b
cc
c
c
c
c
c
c
c
c
c
c
g
g
g
g
h
h
h
Step 1:
Attach pad f onto board 9&10 with screw f (as per below diagram).
Attach one of part d onto board 1&2 with screw e (as per below diagram),then
attach another part d onto the previous part d, please make sure the side with
magnet on the cylinder-part d should be faced to youself. See below diagram
with detials).
side with magnet
Step 2:
Put part c into the corresponding position on board 7&8 and attach board 7&8
onto board 6 with screw part g. Put part c into the corresponding position on
board 6 and attach board 6 onto board 2.(as per below diagram)
Step 3:
Put part c into the corresponding position on board 4&5 and attach board 4&5
onto board 2&7&8 with screw part g.
Step 4:
Fix the screws part a&b onto board 4&5&6 and put part c into the corresponding
position(as per below diagram).
Attach board 1&3 onto bard4&5&6 from previou steps and attach the doors board 9&10
onto board 1&2&3 together with part h (see below detail diagram)
to learn how to fix the part h).
Then fix the round screws part b with
a screwdriver.
At last fix the screws part g onto
board 3 and tighten.
Ensure all parts align. h h

1
11
2
n
n
k
j
m
g
n
n
Step 5:
Use a hammer to attach board 11&12 onto the back with nails part i with a
corresponding position.(as per below diagram).
Step 7:
At last, attach the wall fixing onto the wall with part l&j&g.
Step 6:
Attach wall fixing part m1 onto board 1 with part K&j into a corresponding
position (as per below diagram). Attach stickers onto the screws holes after all.
stickers here to cover the screw holes
same as the other side.
ATTENTION: DO NOT TIGHTEN THE SCREWS FULLY DURING ASSEMBLY. FULLY
TIGHTEN SCREWS AFTER THE FINAL ASSEMBLY STEP.
o o
o
o
o
Warning:
• It is strongly recommended that this product is permanently fixed to the wall.
• Please seek professional advice if you are in doubt of what fixing device to use.
• Regularly check that anchors are securely maintained
•Use safety drawer locks to prevent children climbing
• Stability of tall items may be affected by thick pile carpet or uneven floors
• Do not place unanchored televisions on furniture (If applicable)
Caution: for your safety when attaching the anchor fixings, please note the following:
Check any electrical wires or plumbing inside the wall before drilling any holes (if you are
unsure please seek professional advice from a qualified tradesperson) .