KMART 42917106 User manual

11PC 21PC 31PC
41PC 51PC 61PC
72PCS 81PC 91PC
10 1PC 11 1PC 12 1PC
Hardware list
6PCS
A
CARE INSTRUCTIONS:
WIPE CLEAN WITH SOFT DAMP CLOTH. DO NOT USE SCOURERS,ABRASIVES OR CHEMICAL SOLVENTS. CHECK AND TIGHTEN ALL PARTS REGULARLY. STORE IN A DRY
PLACE AND KEEP AWAY FROM DIRECT WATER AND SUNLIGHT. FOR INDOOR AND DOMESTIC USE ONLY.
WARNING:
DO NOT STAND ON THE PRODUCT. DO NOT USE THE PRODUCT AS A STEP LADDER. DO NOT USE THE PRODUCT UNLESS ALL BOLTS AND SCREWS ARE FIRMLY SECURED.
ALWAYS SET ASSEMBLY REQUIRED. FAILURE TO FOLLOW THESE WARNING COULD RESULT IN SERIOUS INJURY. MAXIMUM SAFE LOAD:
6PCS
B
10PCS
C
4PCS
D
1PC
E
1PC
F
8PCS
G
8PCS
H
1PC
I
2PCS
J
2PCS
K
4PCS
L
4PCS
M
1PC
N
2PCS
O
2PCS
P
1
2
3
4
5
6
7
78
9
10
11
12
Assembly Instructions
6*30mm
15*12mm
6*30mm
4*35mm
Handle
Allen Key
Drawer Stopper
Metal Pin
Nut
Wrench
Wheel without
stopper
Wheel with
stopper
4*16mm
6*40mm
6*25mm
10*10mm
42917106 BENCH PREP TROLLEY
10KG TOP PANEL,2KG FOR DRAWER,
3KG FOR BOTTOM SHELF.
3KG FOR WINESHELF,3KG FOR WIRE BASKET,

Put H onto board 4&7 into the corresponding position (as per diagram). Put part C on toframe 3
into the corresponding position as per diagram. Attach frame board 4&7 onto frame 3 with screw G.
Tighten with Alley key I.
Attach board 6 on to board 7 from step 1.
Put H onto board 4&7 into the corresponding position (as per diagram). Put part C on toframe 2 i
nto the corresponding position as per diagram. Attach frame 2 into board 4&7&6 from step 2 with
screw G.
Attach part O & P onto the legs with screw M&L. Tighten with Alley key I. Kindly reminder: Part O is
the wheel without stopper. Part P is the wheel with stopper.
Note: use part N onto the nut Mto align the part L,tighten with Alley key I.
3
6
2
3
G
G
G
G
C
C
O
O
P
P
O
L
M
N
I
3
4
7
7
C
C
G
G
G
G
I
H
H
STEP1
STEP2
STEP3
STEP4

STEP5
Attach A onto board 1.
Attach board 1 from step 5 onto frame 2&3 from step 4 with screw B & C. Ensure all parts align. Attach board 8 &10 onto board 9 with part D. Put board 11 onto board 8 &10. Fix part A onto board
11, and fix part E onto Board 11 with screwF. Attach board 12 to board 8 &10 with part B&C.
A
1
A
A
A
STEP6
STEP7
1
B
B
BB
8
D
9
10
D
D
D
11
12
A
A
E
F
12
B
B
C
C
C
C
C
C

STEP8
5
K
STEP9
J
J
STEP10
Put part 5 onto trolley from step 8, then fix K into the corresponding position as per diagram.
Finish the assembly.
ATTENTIN:
DO NOT TIGHTENTHE SCREWS DURING ASSEMBLY.
FULLY TIGHTEN AFTERTHE FINAL ASSEMBLY STEP.
Put drawer from step 7 onto trolley from step5,when drawer put into 1/3, then fix J into the
corresponding position as per diagram.