KneeRover KneeCycle User manual

Who we are:
We are committed to providing innovative and affordable mobility
solutions to get you moving as soon as possible after injury or
surgery and for the duration of your recovery –free to go about
your busy, active life –and have a little fun doing it. We are all
about leaving the painful crutches behind and giving you the
Freedom to Move.
The KneeRover®Team is Driven to Change Your Outcome!
Your Satisfaction is Our Top Priority.
Need Parts or Accessories?
Add an accessory like a cup holder or headlight to enhance your
experience on your new KneeRover®scooter. Keep your scooter
operating in top shape with original manufacturer parts. Visit our
exclusive online partner: kneewalkershop.com, to explore our full
range of parts and accessories.
Need Help –Contact Us:
Phone: [phone]
Web: www.kneerover.com
KneeRover® KneeCycle
User Manual
KneeRover®is a registered trademark of Capital Grade Imports LLC.

Congratulations on your purchase of the KneeRover®
KneeCycle!
The deluxe KneeRover®KneeCycle provides a new level of
freedom to users recovering from foot, ankle or lower leg injuries.
This revolutionary product enables users to get back to their
daily routines and enjoy life while recovering –increasing their
mobility without the use of painful crutches.
Operating Instructions:
This medical device is designed to maximize mobility during your
recovery from foot/ankle surgery or injury.
Place the knee of your injured leg on the knee platform and stand as
straight as possible. Adjust the handlebar to waist height so the arms
and hands are in a comfortable position. Adjust the knee platform so
that your injured leg is supported at a 90 degree angle when standing.
Ensure that the hand brake is fully engaged before mounting the
KneeRover®scooter. To move the scooter, simply push forwards or
backwards with your good foot. Allow the scooter to glide, and as it
slows down, push again.
Safety First:
The KneeRover®scooter is designed for easy steering and stopping and
should be used to carefully move about at slow, controlled speeds.
When turning the scooter you should have the brake applied and be
moving at a slow, safe, controlled speed. It is easy to tip the scooter if
you are making a turn with too much speed. Use caution and balance
and operate at your own risk.
With routine use, nuts and bolts on the steering column, steering
mechanism, and brake mechanism can and likely will become loose.
Periodically check nuts and bolts after use and re-tighten as appropriate.
.
Limited Lifetime Warranty
This warranty applies only to the original purchaser.
This device was built to exacting standards and carefully inspected
prior to shipment. Your KneeRover®brand product is warranted to
be free of defects in materials and workmanship for a period of one
year from the date of purchase. The side frames and cross braces are
warranted for the lifetime of the KneeRover®scooter.
This warranty does not cover device failure due to owner misuse,
negligence, or normal wear and tear. The warranty does not extend
to non-durable components, which are subject to normal wear and
need periodic replacement. These components include, but are not
limited to tires, grips, brake pads and upholstery.
The warranty shall not apply for damages or defects caused by
unauthorized parts, attachments or repairs, negligence, accident, or
any circumstances beyond the control of KneeRover®, such as
improper operation, maintenance or storage.
If you have any questions regarding your KneeRover®product or
this warranty, please contact our Customer Care Team. We are
available, for your convenience, toll free at 1-877-737-9877, Monday
–Friday from 9 am to 5 pm Eastern.

Setup Continued & Maintenance:
Step 5: Brake Operation
To engage the brake, squeeze the brake lever on handle bar.
Your KneeRover®scooter comes equipped with a brake lock /
parking brake. Simply squeeze brake handle firmly and press the
button to engage the lock. To release the lock, squeeze the brake
handle again.
Ongoing Maintenance
With routine use, nuts and bolts on the steering column, tie rod
steering mechanism, and brake assembly can become loose. To
ensure safe continuous operation of this KneeRover®scooter, it is
important to periodically inspect the scooter for loose nuts and bolts
and re-tighten as appropriate.
KneeCycle Set Up Instructions:
Please follow the step by step instructions on the following pages to
properly assemble your KneeRover®scooter. The diagram below
identifies the key components of the scooter to aid with assembly.
Hand Brake Lever
8” Non Marking
Wheels
Basket
Adjustable Knee
Platform
Handlebar Height
Adjustment Knob
Quick Release
Clamp
Steering Column
Brake Cable
Rear Brake
Mechanism
Weight Capacity = 300 pounds
Removable Front
Axle
Brake Lock

Setup Instructions:
Step 1: Install Front Axle
Please take your time to carefully complete all steps before operating your
new KneeRover®scooter. First, place the front axle with caster wheels
under the scooter frame, ensuring the round bolts by the wheels are facing
up (as shown in left and right photos). Align the axle and frame holes,
insert the clamp and washer into each hole, and tighten the clamps in a
clockwise motion until the axle is tight against the frame. Press the clamp
lever down firmly until it touches the frame, to lock it in place. The right
photo shows how the clamp should look when properly installed.
Step 2: Install Steering Mechanism
Attached to the front axle you will see two gray bars (the tie rods). Take
one of the tie rods and position it under the black plate that is attached to
the frame. Next take the other tie rod and place it on top of the black plate.
Place the washer on top of the upper tie rod and then thread the bolt from
the bottom to the top, through the tie rods. Finally thread the cotter pin
through the hole on top to lock the assembly in place.
Step 3: Install Steering Column
The steering column will be in a folded position when unpacking. When
facing the front of the KneeRover®scooter, raise the steering column
and push the security pin in the clamp to the left (as shown in left photo)
to allow the column to lock into place. Raise the clamp lever upward
and tighten by turning it clockwise. Finally, push clamp lever down
firmly to secure the steering column (as shown in center photo).
Reverse these steps when needing to lower steering column for
transport. Once knee platform is installed, use the black knob (shown in
right photo) to set the handlebars at a comfortable height for operation.
Step 4: Install Knee Platform & Attach Basket
The knee platform is designed to be used with either the right or left leg.
Remove the knee platform from the bottom of the KneeRover®scooter
by removing the locking pin and loosening the clamp. Next insert the
knee platform post into the receptacle tube and set the knee platform at
your desired height for use by inserting the locking pin through the
aligned holes. Finally, tighten the clamp to secure the knee platform in
place. Removable basket attaches to the steering column.
Locking
Pin
Clamp
Lever
Push Pin to Left
Clamp
Lever
Washer
Round Bolt
Proper Assembly of Tie Rods:
Black Plate
Upper Tie Rod
Washer
Cotter Pin
Lower Tie Rod
Bolt