KneeRover PRO User manual

KneeRover® PRO - All Terrain
User Manual
Patent Pending
Congratulations on your purchase of the KneeRover® Pro
All Terrain Scooter!
Experience the highest level of freedom and performance with the New
KneeRover® Pro scooter - the first all terrain knee walker with an
integrated shock for maximum comfort. Whether you are at home, at work,
on the trail, or on the town, the KneeRover®Pro scooter will keep you on
the move, safely navigating everyday life with ease and adding a little fun
along the way.
Operating Instructions:
This medical device is designed to maximize mobility during your recovery
from foot/ankle surgery or injury.
Place the knee of your injured leg on the knee platform and stand as straight as
possible. Adjust the handlebar to waist height so the arms and hands are in a
comfortable position. Adjust the knee platform so that your injured leg is
supported at a 90 degree angle when standing.
Ensure that the hand brake is fully engaged before mounting the KneeRover®
scooter. To move the scooter, simply push forwards or backwards with your
good foot. Allow the scooter to glide, and as it slows down, push again.
Safety First:
The KneeRover®scooter is designed for easy steering and stopping and should
be used to carefully move about at slow, controlled speeds. When turning the
scooter you should have the brake applied and be moving at a slow, safe,
controlled speed. It is easy to tip the scooter if you are making a turn with too
much speed. Use caution and balance and operate at your own risk.
With routine use, nuts and bolts on the steering column, steering mechanism,
and brake mechanism can and likely will become loose. Periodically check nuts
and bolts after use and re-tighten as appropriate.

KneeRover®Set Up Instructions:
Please follow the step by step instructions on the following pages to
properly assemble your KneeRover®scooter. The diagram below
identifies the key components of the scooter to aid with assembly.
Setup Instructions:
Step 1: Install Front Axle
Please take your time to carefully complete all steps before operating your
KneeRover®scooter. Once the packing material is removed, install the front axle
using the 2 bolts and allen wrench provided. Place the front axle under the frame,
align the holes, insert the bolts, and tighten using the allen wrench provided. The
tie rods should be assembled with one tie rod on top of the black guide, and one
below, with the nut tightened firmly at the bottom. Ensure that the bolt goes into
the top tie rod so that head of the bolt is sitting flush with the top tie rod. . Insert
the lower tie rod into the bolt from the bottom and then flip scooter over to firmly
tighten the nut onto the bolt with the wrench provided (as shown below).
Step 2: Install Steering Column
The steering column will be in a folded position when unpacking. When facing the
front of the KneeRover®scooter, raise the steering column and push the security
pin in the clamp to the left to allow the column to lock into place. Raise the clamp
lever upward and tighten by turning it clockwise. Finally, push clamp lever down
firmly to secure the steering column. Reverse these steps when needing to lower
steering column for transport.
Weight Capacity = 400 pounds
Pneumatic
12” Wheels
Knee Platform
Handlebar Height
Adjustment
Quick Release
Clamp
Steering Column
Brake Cable
Rear Brake
Mechanism
Removable Front
Axle
Hand Brake Lever
Integrated Shock
Technology
2) Push Clamp Lever to Left
to Release Security Pin
To Lower Steering Column:
1) Lift Clamp Lever & Pull
Toward You

Set Up Instructions Continued
Step 3: Install Knee Platform
The knee platform is designed to be used with either the right or left leg.
Remove the knee platform from the bottom of the KneeRover®scooter by
removing the locking pin and loosening the clamp. Next insert the knee
platform post into the receptacle tube and set the knee platform at your
desired height for use by inserting the locking pin through the aligned
holes. Finally, tighten the clamp to secure the knee platform in place.
Step 4: Inflate Tires
The pneumatic tires come partially inflated. It is important to inflate all
three tires to the correct pressure (a maximum of 40 psi) the same way
you inflate a bike tire. Be careful not to over inflate the tires.
Step 5: Brake Operation & Adjustment
To engage the brake, squeeze the brake lever on handle bar. Your
KneeRover®scooter comes equipped with a brake lock / parking
brake. Simply squeeze brake handle firmly and press the button to
engage the lock. To release the lock, squeeze the brake handle again.
If needed, the brake can be adjusted to avoid brake pad(s) from
rubbing a spinning back wheel with a disengaged brake. Use the
provided smaller allen wrench to make adjustments. Approaching the
scooter from behind you can loosen or tighten the brake cable by
loosening the top right bolt, adjusting brake cable, and re-tightening
bolt.
Ongoing Maintenance
With routine use, nuts and bolts on the steering column, tie rod
steering mechanism, and brake assembly can become loose. To
ensure safe continuous operation of this KneeRover®scooter, it is
important to periodically inspect the scooter for loose nuts and bolts
and re-tighten as appropriate. Also, check the tire pressure routinely
to ensure that tires are properly inflated up to 40 psi maximum. Be
careful not to over inflate the tires.
Clamp
Locking Pin
Brake Lock
Top Right Bolt –
Use Allen
Wrench

Who we are:
We are committed to providing innovative and affordable mobility
solutions to get you moving as soon as possible after injury or surgery
and for the duration of your recovery –free to go about your busy,
active life –and have a little fun doing it. We are all about leaving the
painful crutches behind and giving you the Freedom to Move.
The KneeRover®Team is Driven to Change Your Outcome!
Your Satisfaction is Our Top Priority:
Thank you for your business –we appreciate having you as a customer!
We hope that you are completely satisfied with your purchase. If you
have any issues, please contact us and we will do everything possible
to help you. Reviews have a significant impact on our small business.
If you purchased this product on Amazon or eBay, we would greatly
appreciate a review once you’ve had a chance to use your new
KneeRover® scooter. We hope we’ve earned a 4 or 5 star review – if
not, please give us the opportunity to help you before leaving a review.
Thank you for your support. We appreciate you!
Need Help –Contact Us:
Phone: [phone]
Email: [email protected]
Web: www.kneerover.com
Patent Pending
Limited Lifetime Warranty:
This warranty applies only to the original purchaser.
This device was built to exacting standards and carefully inspected
prior to shipment. Your KneeRover®brand product is warranted
to be free of defects in materials and workmanship for a period of
one year from the date of purchase. The side frames and cross
braces are warranted for the lifetime of the KneeRover®scooter.
This warranty does not cover device failure due to owner misuse,
negligence, or normal wear and tear. The warranty does not
extend to non-durable components, which are subject to normal
wear and need periodic replacement. These components include,
but are not limited to tires, grips, brake pads and upholstery.
The warranty shall not apply for damages or defects caused by
unauthorized parts, attachments or repairs, negligence, accident,
or any circumstances beyond the control of KneeRover®, such as
improper operation, maintenance or storage.
If you have any questions regarding your KneeRover®product or
this warranty, please contact our Customer Care Team. We are
available, for your convenience, toll free at 1-877-737-9877,
Monday –Friday from 9 am to 5 pm Eastern.
Need Parts or Accessories?
Add an accessory like a deluxe backpack, knee pad cover, cup
holder or headlight to enhance your experience on your new
KneeRover®Pro scooter. Keep your scooter operating in top shape
with original manufacturer parts. Visit our exclusive online
partner: kneewalkershop.com, to explore our full range of parts
and accessories.
KneeRover®is a registered trademark of Capital Grade Imports LLC.