Knox KLS-1500 User manual
KNOX ELOCK CORE RETROFIT
KLS-1500 HOMEBOX INSTALLATION GUIDE
Figure 2
Knox eLock Core
& Shell Installation
Figure 1
Mechanical Lock
Core & Shell Removal
CAUTION:
Activate Knox eKey and Knox eLock Core prior to installation!
The Knox eLock Core and the Knox eKey must be activated before
installation of the Knox eLock Core. See the KnoxConnect™Management System Administrator User Guide for further instructions.
Installation Time:
Less than
10 minutes
Stop
Washer
Lock
Shell Nut
Cam
Lock
Washer
Lock
Cam Nut
Dust Cover
Bracket
Dust
Cover
Knox eLock
Shell
Knox eLock
Core
Knox Rain
Guard
Knox eKey
Stop
Washer
Lock
Shell Nut
Cam
Lock
Washer
Lock
Cam Nut
Dust Cover
Magnet
Mechanical
Lock Shell
Dust Cover
Bracket
Dust
Cover
Mechanical
Lock Core
Mechanical
Key
OPE-ESYSLR-0338-B
©Knox Company. All Rights Reserved
KNOX ELOCK CORE RETROFIT:
KLS-1500 KNOX HOMEBOX INSTALLATION GUIDE
2
1601 W. DEER VALLEY RD. PHOENIX, AZ 85027 | T. 800-552-5669 | F. 623-687-2290 | TECHSUPPORT@KNOXBOX.COM | KNOXBOX.COM
MECHANICAL LOCK CORE REMOVAL
Disassemble the Mechanical Lock:
Lift the Dust Cover, insert the key, and
open the lock box.
Use a 7/8" socket or wrench to remove the
Lock Shell Nut from the inside of the door.
Remove the Lock Shell, Dust Cover,
and Dust Cover Bracket from the
outside of the door.
Use a 9/16" socket or wrench to
remove the Lock Cam by removing the
Lock Cam Nut and Lock Washer. Put
the Lock Cam and remaining hardware,
aside for later use.
Remove the Lock Core. Pull out the
key along with the Lock Core from the
outside of the door.
1
4 5
2 3
NOTE:
Set all the hardware aside for later use.
IMPORTANT:
Return Lock Shell with the Lock Core and Mechanical Key to
Knox Company. Contact Technical Support for return instructions.
NOTE:
For illustration of part
disassembly, see rst page.
OPE-ESYSLR-0338-B
©Knox Company. All Rights Reserved
KNOX ELOCK CORE RETROFIT:
KLS-1500 KNOX HOMEBOX INSTALLATION GUIDE
3
1601 W. DEER VALLEY RD. PHOENIX, AZ 85027 | T. 800-552-5669 | F. 623-687-2290 | TECHSUPPORT@KNOXBOX.COM | KNOXBOX.COM
CAUTION:
Activate Knox eKey and Knox eLock Core prior to installation!
The Knox
eLock Core and the Knox eKey must be activated before installation of the Knox
eLock Core. See the KnoxConnect™Management System Administrator User
Guide for further instructions.
KNOX ELOCK CORE INSTALLATION
Assemble the Knox eLock Core:
Line up the sidebar of the Knox eLock
Core with the groove in the Lock Shell
and slide the Lock Core into the Lock
Shell from the outside of the door.
Insert the Dust Cover, Dust Cover
Bracket, and the Knox eLock Shell into
the outside of the door as shown in
Figure 2 on Page 1.
Install the Lock Shell Nut onto the Lock
Shell from the inside of the door. Ensure
the tab on the Lock Shell is orientated to
the left.Use a 7/8" socket or wrench to
tighten the nut to snug.
3
1 2
Reinstall the Cam Stop Washer onto
the Lock Core from the inside of the door.
Insert the Shim Washers up against the
Stop Washer. Reinsert the Lock Cam
followed by the Lock Washer. Reinstall
and hand tighten the Lock Cam Nut.
456
Close the door, rotate the Knox eKey
clockwise, and remove the key.
9
To ensure the Knox eLock Core
installation was successful, test the
Knox eLock Core BEFORE closing the
box. Enter your command code, insert
the Knox eKey, and rotate the key
counter-clockwise.
8
Using the activated Knox eKey, turn the
lock to the unlock position. Place a screw
driver next to the edge of the Cam as
shown below to prevent the Cam from
turning, and tighten the nut to snug using
a 9/16" socket or wrench.
7
IMPORTANT:
Ensure that the Stop Washer is
orientated as shown in the image above.
Enter your command code and
insert the Knox eKey into the Knox
eLock Core to unlock the unit (see
steps below picture).
a. Rotate the Knox eKey 90° counter-clockwise.
b. Check the inside of the door to make
certain the Stop Washer is in place and
has not slid o the Lock Core. If so,
re-secure the Stop Washer.
c. If the key turns clockwise rather than
counter-clockwise, go back to Step 4 and
change the position of the Stop Washer.
WARNING!
Upon reinstallation of the Lock Cam,
DO NOT CLOSE AND LOCK THE BOX!
NOTE:
Cam shown in the locked position above.
IMPORTANT!
Do not attempt without using
screwdriver. This will prevent
damage to the Knox eLockCore
while tightening the nut.
OPE-ESYSLR-0338-B
©Knox Company. All Rights Reserved
KNOX ELOCK CORE RETROFIT:
KLS-1500 KNOX HOMEBOX INSTALLATION GUIDE
4
1601 W. DEER VALLEY RD. PHOENIX, AZ 85027 | T. 800-552-5669 | F. 623-687-2290 | TECHSUPPORT@KNOXBOX.COM | KNOXBOX.COM
This concludes the Knox eLock Core Retrot Instructions.
Installation of the Knox RainGuard™:
Use a sharp instrument to remove the
adhesive backing from the bottom half of
the Knox RainGuard. The bottom half is
the section with the open circle.
12
Use the provided alcohol wipe to clean
the backside of the Dust Cover and the
surface area all around the Lock (see note
below regarding Dust Cover Magnet).
11
NOTE:
Use a at head screwdriver to remove
the Dust Cover Magnet.
Mount the Knox RainGuard to the
Dust Cover Bracket. The Knox
RainGuard’s open circle will t tightly
around the Lock Shell.
13 Using the nose of the foam as a
guide, fold the upper half of the Knox
RainGuard to align with the Lock Core
center. The nose will fold over and into
the Lock Core for protection.
14 Remove the adhesive backing from the
back side of the Knox RainGuard's upper
half. Pull out and close the Dust Cover
with pressure allowing the Knox RainGuard
to rmly attach to the Dust Cover. Lift the
Dust Cover up and press both halves of
the Knox RainGuard for a rm t.
15
Lastly, remove the adhesive backing
from the Knox "K" reective label, and
place front and center of the Dust Cover.
15
Use a athead screw driver to remove the
Dust Cover Magnet from the Dust Cover
Bracket.
10
Other Knox Lock manuals
