Koala Kare KB850-KD User manual

®®
KB850-KD Diner High Chair Assembly Instructions
Please Note: This product is intended for children able
to sit up unaided and up to 3 years or a maximum weight
of 15 kg. This product is designed to be used by an infant
or child capable of sitting upright and unassisted. Waist
restraint strap should be buckled at all times when in use.
Restraint Usage: To fasten the waist strap, push spring
tabs into the buckle receptacle until both lock in place with
an audible “click”.
The waist restraint can be adjusted to make the strap
tighter or looser.
WARNING:
Prevent serious injury or death from falls or sliding out. Do
not leave child unattended.
Always use the restraint system. Make sure harness is
correctly tted to child before use.
The child should be secured in the high chair at all times
by the restraining system.
Always keep child in view while in the high chair. Never
leave the child unattended.
It is recommended that the high chair be used only by
children capable of sitting upright an unassisted.
Do not use the high chair unless all components are
correctly tted and adjusted. Do not use high chair if any
part is broken, torn or missing.
Be aware of the risk of open re and other sources of
strong heat, such as electric bar res, gas res, etc. in the
vicinity of the high chair.
FALLING HAZARD: Prevent your child from climbing on the
product.
Inspection Criteria - A properly
maintained unit:
• Has both ends of a functioning, non-frayed
strap: buckle clicks when closed and is attached
at both ends on seat bottom.
• Has an intact warning label afxed to the
seat back. (If damaged or unreadable, please
replace.)
• All plastic parts rmly attached by provided
hardware, and should be tightened as
necessary.
Maintenance: Clean and sanitize regularly.
Wipe down The Diner High Chair with a soft rag
using a non-abrasive cleaner.
Important: DO NOT USE BLEACH on this prod-
uct. May cause discoloration. Use of bleach on
this product will void warranty. Do not use abra-
sive cleaners as they can scratch the product.
You are responsible for the safe operation of this unit.
Koala Kare Products A Division of Bobrick
6982 South Quentin St., Centennial, CO 80112-3945
Main 303.539.8300 Toll Free 888.733.3456
Fax [phone]
Koalabear.com
P/N 1288 - September 2017
IMPORTANT! READ CAREFULLY AND KEEP FOR FUTURE REFERENCE.

®®
KB850-KD Diner High Chair Assembly Instructions
KB850 Package Contents
Left and Right Legs
Front and Rear Support Bars
T-Bar
Seat Base (with strap)
Seat Back (with labels)
¼-20 x 1¼” Bolts (8 pc)
¼-20 x 1¾” Bolts (4 pc)
(Used for attaching the seat ONLY)
Plastic Washers (12 pc)
Bolt Covers (12 pc)
Tools Needed
Phillips Head Screwdriver
Assembly Instructions
Step 1. Thread one plastic washer on each of the bolts. The bolt head should sit within the “petals” of the plastic
washer. Separate the 1¼” bolts with washers from the 1¾” bolts with washers.
Step 2. Assemble the t-bar and seat base by inserting bottom of t-bar into the recess on the seat surface.
Step 3. Attach the seat base and t-bar to the right leg using 1¾” bolts for the seat base and the 1¼” bolt
for the t-bar.
Step 4. Using the 1¼” bolts, attach the front and rear support bars to the right leg. The textured side of the
bars should be facing out and the small holes facing the oor.
Step 5. Attach the seat back to the right leg using the 1¼” bolts. Label should be facing outward (away
from the t-bar).
Step 6. Lay the partially assembled chair on the right leg so that the components are facing up and place
the left leg on top. Attach the seat to the left leg using the 1¾” bolts.
Step 7. Attach the remaining pieces to the left leg using the 1¼” bolts.
Step 8. Double check that all bolts are tight. Snap bolt covers on all exposed bolt heads.
Check and tighten all connections
Do not overtighten