Kobalt CDT212KU User manual

1
KOBALT® and the K Design® are registered
trademarks of LF, LLC. All Rights Reserved.
Questions, problems, missing parts? Before returning to your retailer, call our customer
service department at 1-888-3KOBALT (1-888-356-2258), 8 a.m. - 8 p.m., EST,
Monday - Friday.
ATTACH YOUR RECEIPT HERE
Serial Number Purchase Date
AB13594B
Español p. 29
Français p. 15
MODEL #CDT212KU
12 V DRILL DRIVER
ITEM #0233384

2
kobalttools.com
TABLE OF CONTENTS
PRODUCT SPECIFICATIONS
3URGXFW6SHFL¿FDWLRQV......................................................................................................... 2
Package Contents ............................................................................................................... 3
Safety Information ............................................................................................................... 4
Operating Instructions ......................................................................................................... 8
Care and Maintenance ..................................................................................................... 13
Troubleshooting................................................................................................................ 13
Warranty ........................................................................................................................... 14
Replacement Parts List .................................................................................................... 14
COMPONENT SPECIFICATIONS
Charger Voltage 120 V ~ 60 Hz
Rated Voltage 12 V
No Load Speed 330/1,200min.
Number of Clutch Positions 15+1
Max Torque 210 in.-lbs.
Chuck Capacity 3/8 in.
Max. Drilling Capacity Steel 3/8 in.
Wood 13/16 in.
Charging Time 35 min.
Machine Weight 2.6 lbs.

3
kobalttools.com
PACKAGE CONTENTS
PART DESCRIPTION
A Keyless Chuck
B E-Torque Selector
C Two-Speed Gear Control
D Forward/Reverse Rotation
Control
E Fuel Gauge
F Soft Grip Handle
G Belt Clip
PART DESCRIPTION
H Battery Release Button
I Battery Pack
J On/Off Switch
K LED Light
L Double-Sided Bit
M Charger
A B C
D
L
M
E
F
GH
I
J
K

4
kobalttools.com
Please read and understand this entire manual before attempting to assemble, operate or install
the product. If you have any questions regarding the product, please call customer service at
1-888-3KOBALT (1-888-356-2258), 8 a.m. - 8 p.m., EST, Monday - Friday.
This instruction manual contains important information necessary for the proper assembly and safe use
of this tool. Read and follow all warnings and instructions before assembling and using this tool.
CALIFORNIA PROPOSITION 65
6RPHGXVWFUHDWHGE\SRZHUVDQGLQJVDZLQJJULQGLQJGULOOLQJDQGRWKHUFRQVWUXFWLRQDFWLYLWLHV
contains chemicals known to the state of California to cause cancer, birth defects or other
reproductive harm.
$OLVWLQJRIWKHVHFKHPLFDOVFDQEHREWDLQHGIURPZZZRHKKDFDJRY
6RPHH[DPSOHVRIWKHVHFKHPLFDOVDUHOHDGIURPOHDGEDVHGSDLQWVFU\VWDOOLQHVLOLFDIURPEULFNV
and cement and other masonry products, and arsenic and chromium from chemically treated
lumber.
<RXUULVNIURPWKHVHH[SRVXUHVYDULHVGHSHQGLQJRQKRZRIWHQ\RXGRWKLVW\SHRIZRUN7RUHGXFH
your exposure to these chemicals: work in a well-ventilated area, and work with approved safety
HTXLSPHQWVXFKDVDUHVSLUDWRURUGXVWPDVNVSHFLDOO\GHVLJQHGWR¿OWHURXWPLFURVFRSLFSDUWLFOHV
GENERAL POWER TOOL SAFETY WARNINGS
Read all safety warnings and instructions. Failure to follow the warnings and instructions may result in
HOHFWULFVKRFN¿UHDQGRUVHULRXVLQMXU\
The term power tool in the warnings refers to your electric (corded) power tool or battery operated
(cordless) power tool.
Save all warnings and instructions for future reference.
WORK AREA SAFETY
Keep work area clean and well lit.
&OXWWHUHGRUGDUNDUHDVLQYLWHDFFLGHQWV
DO NOTRSHUDWHSRZHUWRROVLQH[SORVLYHDWPRVSKHUHVVXFKDVLQWKHSUHVHQFHRIÀDPPDEOH
liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
.HHSFKLOGUHQDQGE\VWDQGHUVDZD\ZKLOHRSHUDWLQJDSRZHUWRRO'LVWUDFWLRQVFDQFDXVH\RXWRORVH
control.
ELECTRICAL SAFETY
Power tool plugs MUST match the outlet. NEVER modify the plug in any way. DO NOT use any
DGDSWHUSOXJVZLWKJURXQGHGSRZHUWRROV8QPRGL¿HGSOXJVDQGPDWFKLQJRXWOHWVZLOOUHGXFHULVNRI
electric shock.
$YRLGERG\FRQWDFWZLWKJURXQGHGVXUIDFHVVXFKDVSLSHVUDGLDWRUVUDQJHVDQGUHIULJHUDWRUV7KHUH
is an increased risk of electric shock if your body is grounded.
DO NOT expose power tools to rain or wet conditions. Water entering a power tool will increase the
risk of electric shock.
DO NOT abuse the cord. NEVER use the cord for carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase
the risk of electric shock.
SAFETY INFORMATION

5
kobalttools.com
SAFETY INFORMATION
:KHQRSHUDWLQJDSRZHUWRRORXWGRRUVXVHDQH[WHQVLRQFRUGVXLWDEOHIRURXWGRRUXVHPDUNHG³:
$´RU³:´8VHRIDFRUGVXLWDEOHIRURXWGRRUXVHUHGXFHVWKHULVNRIHOHFWULFVKRFN
,IRSHUDWLQJDSRZHUWRROLQDGDPSORFDWLRQLVXQDYRLGDEOHXVHD*URXQG)DXOW&LUFXLW,QWHUUXSWHU
(GFCI) protected supply. Use of a GFCI reduces the risk of electric shock.
PERSONAL SAFETY
Stay alert, watch what you are doing and use common sense when operating a power tool.
DO NOTXVHDSRZHUWRROZKLOH\RXDUHWLUHGRUXQGHUWKHLQÀXHQFHRIGUXJVDOFRKRORUPHGLFDWLRQ
$PRPHQWRILQDWWHQWLRQZKLOHRSHUDWLQJSRZHUWRROVPD\UHVXOWLQVHULRXVSHUVRQDOLQMXU\
8VHSHUVRQDOSURWHFWLYHHTXLSPHQWALWAYS wear eye protection. Protective equipment such as
dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions
ZLOOUHGXFHSHUVRQDOLQMXULHV
3UHYHQWXQLQWHQWLRQDOVWDUWLQJ(QVXUHWKHVZLWFKLVLQWKHRIISRVLWLRQEHIRUHFRQQHFWLQJWRSRZHU
VRXUFHDQGRUEDWWHU\SDFNSLFNLQJXSRUFDUU\LQJWKHWRRO&DUU\LQJSRZHUWRROVZLWK\RXU¿QJHURQ
the switch or energizing power tools that have the switch on invites accidents.
5HPRYHDQ\DGMXVWLQJNH\RUZUHQFKEHIRUHWXUQLQJWKHSRZHUWRRORQ$ZUHQFKRUDNH\OHIW
DWWDFKHGWRDURWDWLQJSDUWRIWKHSRZHUWRROPD\UHVXOWLQSHUVRQDOLQMXU\
DO NOT overreach. Keep proper footing and balance at all times. This enables better control of the
power tool in unexpected situations.
'UHVVSURSHUO\DO NOTZHDUORRVHFORWKLQJRUMHZHOU\.HHS\RXUKDLUFORWKLQJDQGJORYHVDZD\
IURPPRYLQJSDUWV/RRVHFORWKHVMHZHOU\RUORQJKDLUFDQEHFDXJKWLQPRYLQJSDUWV
,IGHYLFHVDUHSURYLGHGIRUWKHFRQQHFWLRQRIGXVWH[WUDFWLRQDQGFROOHFWLRQIDFLOLWLHVHQVXUHWKHVH
are connected and properly used. Use of dust collection can reduce dust-related hazards.
POWER TOOL USE AND CARE
DO NOT force the power tool. Use the correct power tool for your application. The correct power tool
ZLOOGRWKHMREEHWWHUDQGVDIHUDWWKHUDWHIRUZKLFKLWZDVGHVLJQHG
DO NOT use the power tool if the switch does not turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must be repaired.
'LVFRQQHFWWKHSOXJIURPWKHSRZHUVRXUFHDQGRUWKHEDWWHU\SDFNIURPWKHSRZHUWRROEHIRUH
PDNLQJDQ\DGMXVWPHQWVFKDQJLQJDFFHVVRULHVRUVWRULQJSRZHUWRROV6XFKSUHYHQWLYHVDIHW\
measures reduce the risk of starting the power tool accidentally.
6WRUHLGOHSRZHUWRROVRXWRIWKHUHDFKRIFKLOGUHQDQGGRQRWDOORZSHUVRQVXQIDPLOLDUZLWKWKH
power tool or these instructions to operate the power tool. Power tools are dangerous in the hands
of untrained users.
0DLQWDLQSRZHUWRROV&KHFNIRUPLVDOLJQPHQWRUELQGLQJRIPRYLQJSDUWVEUHDNDJHRISDUWVDQGDQ\
other condition that may affect the power tool's operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly maintained power tools.
.HHSFXWWLQJWRROVVKDUSDQGFOHDQ3URSHUO\PDLQWDLQHGFXWWLQJWRROVZLWKVKDUSFXWWLQJHGJHVDUH
less likely to bind and are easier to control.
8VHWKHSRZHUWRRODFFHVVRULHVDQGWRROELWVHWFLQDFFRUGDQFHZLWKWKHVHLQVWUXFWLRQVDQGLQWKH
manner intended for the particular type of power tool, taking into account the working conditions and
the work to be performed. Use of the power tool for operations different from those intended could
result in a hazardous situation.

6
kobalttools.com
BATTERY TOOL USE AND CARE
5HFKDUJHRQO\ZLWKWKHFKDUJHUVSHFL¿HGE\WKHPDQXIDFWXUHU$FKDUJHUWKDWLVVXLWDEOHIRURQHW\SH
RIEDWWHU\SDFNPD\FUHDWHDULVNRI¿UHZKHQXVHGZLWKDQRWKHUEDWWHU\SDFN
8VHSRZHUWRROVRQO\ZLWKVSHFL¿FDOO\GHVLJQDWHGEDWWHU\SDFNV8VHRIDQ\RWKHUEDWWHU\SDFNVPD\
FUHDWHDULVNRILQMXU\DQG¿UH
:KHQEDWWHU\SDFNLVQRWLQXVHNHHSLWDZD\IURPRWKHUPHWDOREMHFWVOLNHSDSHUFOLSVFRLQVNH\V
QDLOVVFUHZVRURWKHUVPDOOPHWDOREMHFWVWKDWFDQPDNHDFRQQHFWLRQIURPRQHWHUPLQDOWRDQRWKHU
6KRUWLQJWKHEDWWHU\WHUPLQDOVWRJHWKHUPD\FDXVHEXUQVRUD¿UH
8QGHUDEXVLYHFRQGLWLRQVOLTXLGPD\EHHMHFWHGIURPWKHEDWWHU\DYRLGFRQWDFW,IFRQWDFW
DFFLGHQWDOO\RFFXUVÀXVKZLWKZDWHU,IOLTXLGFRQWDFWVH\HVDGGLWLRQDOO\VHHNPHGLFDOKHOS/LTXLG
HMHFWHGIURPWKHEDWWHU\PD\FDXVHLUULWDWLRQRUEXUQV
SERVICE
+DYH\RXUSRZHUWRROVHUYLFHGE\DTXDOL¿HGUHSDLUSHUVRQXVLQJRQO\LGHQWLFDOUHSODFHPHQWSDUWV
This will ensure that the safety of the power tool is maintained.
DRILL SAFETY WARNINGS
Hold power tool by insulated gripping surfaces when performing an operation where the cutting ac-
FHVVRU\PD\FRQWDFWKLGGHQZLULQJ&XWWLQJDFFHVVRU\FRQWDFWLQJD³OLYH´ZLUHPD\PDNHH[SRVHG
PHWDOSDUWVRIWKHSRZHUWRRO³OLYH´DQGFRXOGJLYHWKHRSHUDWRUDQHOHFWULFVKRFN
GENERAL SAFETY WARNINGS FOR BATTERY PACK
WARNING:
5LVNRI¿UHDQGEXUQVDO NOT disassemble, heat above 100°C (212°F), or incinerate.
DO NOTH[SRVHFHOOVRUEDWWHULHVWRKHDWRU¿UH$YRLGVWRUDJHLQGLUHFWVXQOLJKW
DO NOT use a visibly damaged battery pack or appliance as applicable.
DO NOT modify or attempt to repair the appliance or the battery pack as applicable.
'LVSRVHRIXVHGEDWWHULHVSURPSWO\DFFRUGLQJWRORFDOUHF\FOLQJRUZDVWHUHJXODWLRQV
'LVSRVHRIXVHGEDWWHU\SURPSWO\DO NOTGLVSRVHRILQ¿UH
.HHSEDWWHU\RXWRIUHDFKRIFKLOGUHQDQGLQRULJLQDOSDFNDJHXQWLOUHDG\WRXVH
NEVER put batteries in mouth. If swallowed, contact your physician or local poison control center.
CAUTION
7KHEDWWHU\XVHGLQWKLVGHYLFHPD\SUHVHQWDULVNRI¿UHRUFKHPLFDOEXUQLIPLVWUHDWHG5HSODFH
EDWWHU\ZLWKVDPH.REDOW9EDWWHU\RQO\8VHRIDQRWKHUEDWWHU\PD\SUHVHQWDULVNRI¿UHRU
explosion.
3OHDVHUHDGDQGXQGHUVWDQGWKLVHQWLUHPDQXDOEHIRUHDWWHPSWLQJWRDVVHPEOHRSHUDWHRULQVWDOOWKH
product.
SAFETY INFORMATION

7
kobalttools.com
BATTERY MUST BE RECYCLED.
5HFKDUJHRQO\ZLWKWKHFKDUJHUVSHFL¿HGE\WKHPDQXIDFWXUHU$FKDUJHUWKDWLVVXLWDEOHIRURQHW\SH
RIEDWWHU\SDFNPD\FUHDWHDULVNRI¿UHZKHQXVHGZLWKDQRWKHUEDWWHU\SDFN
DO NOT short-circuit a cell or battery. DO NOT store cells or batteries haphazardly in a box or
drawer where they may short-circuit each other or be short-circuited by conductive materials.
DO NOTVXEMHFWFHOOVRUEDWWHULHVWRPHFKDQLFDOVKRFN
.HHSFHOOVDQGEDWWHULHVFOHDQDQGGU\:LSHWKHFHOORUEDWWHU\WHUPLQDOVZLWKDFOHDQGU\FORWKLI
they become dirty.
6HFRQGDU\FHOOVDQGEDWWHULHVQHHGWREHFKDUJHGEHIRUHXVHALWAYS refer to the cell or battery
manufacturer’s instructions and use the correct charging procedure.
DO NOT maintain secondary cells and batteries on charge when not in use.
5HWDLQWKHRULJLQDOFHOODQGEDWWHU\OLWHUDWXUHIRUIXWXUHUHIHUHQFH
:KHQGLVSRVLQJRIVHFRQGDU\FHOOVRUEDWWHULHVNHHSFHOOVRUEDWWHULHVRIGLIIHUHQWHOHFWURFKHPLFDO
systems separate from each other.
8VHRQO\WKHFHOORUEDWWHU\LQWKHDSSOLFDWLRQIRUZKLFKLWZDVLQWHQGHG
KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE.
SAFETY INFORMATION

8
kobalttools.com
2. After recharge, slide the battery pack (I) into the
battery port. A simple push and slight pressure
ZLOOEHVXI¿FLHQW
2
I
USING YOUR BATTERY PACK
Note: Before using the tool, read the instruction book carefully.
WARNING: 7KHFKDUJHUDQGEDWWHU\SDFNDUHVSHFL¿FDOO\GHVLJQHGWRZRUNWRJHWKHUVRDO
NOT attempt to use any other devices. NEVERLQVHUWRUDOORZPHWDOOLFREMHFWVLQWR\RXUFKDUJHURU
battery pack connections because an electrical failure and hazard will occur.
<RXUEDWWHU\SDFNLVUNCHARGED and you must charge once before use. When you charge the
new battery or one which has not been used for long periods of time, it may not reach full charge
until after you have discharged it fully in use and recharged it several times.
OPERATING INSTRUCTIONS
1. Plug the charger (M) into an appropriate outlet.
The light will be green. Insert the battery pack
,LQWRWKHFKDUJHU7KHOLJKWZLOOÀDVKUHGWR
indicate the charging process has started. On
completion of charge, the light will turn solid
green. The pack is now fully charged. Unplug
the charger and remove the battery pack.
WARNING
When battery charge runs out after continuous
use or exposure to direct sunlight or heat,
allow time for the battery to cool down before
recharging to achieve the full charge.
1
M
I

9
kobalttools.com
3. To remove the battery pack (I), depress battery
release button (H) and remove the battery pack
from your tool.
3
1
H
I
OPERATING INSTRUCTIONS
<RXUWRROLVHTXLSSHGZLWKDIXHOJDXJH(
Press the On/Off switch fully and the fuel gauge
will light up for 2-3 seconds to show the amount
of charge left in the battery.
4
E
FUEL GAUGE CAPACITY
3 Red Lights >2/3
2 Red Lights >1/3
1 Red Light <1/3
1 Flashing Light Reserve

10
kobalttools.com
DRILL FEATURES
1. Depress the On/Off switch (J) to start and
release it to stop your drill. The LED light (K) will
turn on when you press the On/Off switch (J).
7KH2Q2IIVZLWFKLV¿WWHGZLWKDEUDNHIXQFWLRQ
which stops your chuck immediately when you
quickly release the switch. It is also a variable
speed switch that delivers higher speed and
torque with increased trigger pressure. Speed is
controlled by the amount of switch trigger
depression.
WARNING
DO NOT operate for long periods at low speed
because excess heat will be produced internally.
2. The On/Off switch (J) can be locked in the OFF
position. This helps to reduce the possibility of
accidental starting when not in use. To lock the
On/Off switch, place the forward/reverse rotation
control in the center position.
For drilling and screw driving, use forward
URWDWLRQPDUNHG³!!´IRUZDUGUHYHUVHIRWDWLRQ
control is moved to the left). Only use reverse
URWDWLRQPDUNHG³´IRUZDUGUHYHUVHURWDWLRQ
control is moved to the right) to remove screws
RUUHOHDVHDMDPPHGGULOOELW
WARNING
NEVER change the direction of rotation when
the chuck is rotating. Wait until it has stopped!
BELT CLIP
1. The belt clip is attached with a small screw.
Simply unscrew the clip to move it to the opposite
side of the drill. The belt clip (G) can be hooked
on your belt or pocket, etc.
OPERATING INSTRUCTIONS
1
J
K
2
Clockwise CounterclockwiseLocked
D
1
1
G

11
kobalttools.com
3. The drill has a two-speed gear control (C)
designed for drilling or driving at LO (1) or HI (2)
speeds. A slide switch is located on top of the
drill to select either LO or HI speed. When using
the drill in the LO speed range, the speed will
decrease and the drill will have greater power
and torque. When using the drill in the HI speed
range, the speed will increase and the drill will
have less power and torque.
GEAR 1: Low speed range for screwdriving or
working with large drilling diameter.
GEAR 2: High speed range for working with
small drilling diameter.
WARNING
To prevent gear damage, ALWAYS allow the
chuck to come to a complete stop before
changing the gear speed.
4. With the chuck (A) facing you, rotate the chuck
FRXQWHUFORFNZLVHWRRSHQWKHMDZV,QVHUWWKH
GULOOELWEHWZHHQWKHFKXFNMDZV5RWDWHWKH
FKXFNFORFNZLVHWRWLJKWHQWKHMDZV(QVXUHWKDW
WKHGULOOELWLVVHDWHGLQWKHFHQWHURIWKHMDZV
OPERATING INSTRUCTIONS
2
4
1
3
L
A
3
C
7KHWRUTXHLVDGMXVWHGE\URWDWLQJWKH(WRUTXH
selector (B). The torque is greater when the
E-torque selector is set on a higher setting. The
torque is less when the E-torque selector is set
on a lower setting.
Make the setting as follows:
5
B
TORQUE
SETTING PURPOSE
1-4 Driving small screws
5-9 Driving screws into soft material
10-15
Driving screws into soft and hard material
Heavy drilling

12
kobalttools.com
OPERATING INSTRUCTIONS
6. The automatic spindle lock allows you to use
WKHGULOODVDUHJXODUVFUHZGULYHU<RXFDQJLYH
DQH[WUDWZLVWWR¿UPO\WLJKWHQDVFUHZORRVHQ
a very tight screw, or continue working when
the battery energy has expired. For manual
screwdriver purposes, the chuck is automatically
locked when the tool is off.
6
DRILLING
When drilling into a hard, smooth surface, use a center punch to mark the desired hole location. This
ZLOOSUHYHQWWKHGULOOELWIURPVOLSSLQJRIIFHQWHUDVWKHKROHLVVWDUWHG+ROGWKHWRRO¿UPO\DQGSODFH
the tip of the bit at the point to be drilled. Depress the switch trigger to start the tool. Move the drill bit
into the workpiece, applying only enough pressure to keep the bit cutting. DO NOT force or apply side
pressure to elongate a hole.
WARNING
Tungsten carbide drill bits should always be used for concrete and masonry. When drilling in metal,
only use HSS drill bits in good condition. ALWAYS use a magnetic bit holder (not included) when
using short screwdriver bits. When driving screws, apply a small quantity of liquid soap or similar to
the screw threads to ease insertion.
BATTERY DISPOSAL
To preserve natural resources, please recycle or dispose of the battery pack properly. This battery
pack contains lithium batteries. Consult your local waste authority for information regarding available
recycling and/or disposal options. Discharge your battery pack by operating your drill, then remove
the battery pack from the drill housing and cover the battery pack connections with heavy-duty
adhesive tape to prevent short circuit and energy discharge. DO NOT attempt to open or remove any
of the components.

13
kobalttools.com
CARE AND MAINTENANCE
<RXUSRZHUWRROUHTXLUHVQRDGGLWLRQDOOXEULFDWLRQRUPDLQWHQDQFH7KHUHDUHQRXVHUVHUYLFHDEOHSDUWV
in your power tool. NEVER use water or chemical cleaners to clean your power tool. Wipe clean with
a dry cloth. ALWAYS store your power tool in a dry place. Keep the motor ventilation slots clean. Keep
all working controls free of dust. Occasionally you may see sparks through the ventilation slots. This is
normal and will not damage your power tool.
TROUBLESHOOTING
PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION
The drill will not turn on
when the On/Off switch
is pressed.
The forward/reverse rotation
control, which is on top of the
trigger, is positioned in the lock
function.
Unlock the forward/reverse rotation
control by putting it into the required
rotation position. Push the On/Off
switch and the drill will start to rotate.
The drill stops before
the screw is completely
tightened.
The torque setting of the
E-torque selector is set on a low
torque setting.
Position 1 is the lowest torque (screw
driving force) and position 15 is the
highest torque (screw driving force).
Position 16 is for drill operation.
Regulate the E-torque selector to a
higher position to reach the best result.
Battery pack does not
hold a charge or needs
to be recharged often.
1. Battery pack has not been
used for a prolonged time.
2. Heavy working conditions
such as large screws into
hard wood.
3. Battery pack was charged
below 32°F (0°C) or above
113°F (45°C).
1. This can be corrected after several
charge and discharge operations by
charging & working with your drill.
2. Heavy working conditions will use up
the battery pack energy faster. Make
sure torque setting is correct.
3. The battery pack must be charged
between 32°F (0°C) and 113°F
(45°C) for optimal use.

14
kobalttools.com
KOBALT® and the K Design® are
registered trademarks of LF, LLC. All
Rights Reserved.
Printed in China
WARRANTY
<($5:$55$17<67$7(0(17)25.2%$/79&25'/(66&20%2.,7
,IWKLV.REDOWWRROEHFRPHVGHIHFWLYHGXHWRIDXOW\PDWHULDOVRUZRUNPDQVKLSZLWKLQ¿YH\HDUVIURP
the date of purchase, the manufacturer guarantees to:
5HSODFHRUUHSDLUDOOGHIHFWLYHSDUWVRUSURGXFWVIUHHRIFKDUJHRU
5HSODFHWKHXQLWZLWKDQHZRUUHFRQGLWLRQHGXQLWIUHHRIFKDUJHRU
5HIXQGWKHRULJLQDOSXUFKDVHSULFH
For guarantee claims, simply return the tool along with proof of purchase to the place of purchase, or
contact 1-888-3KOBALT (1-888-2258), 8 a.m. – 8 p.m., EST, Monday – Friday.
<RXUZDUUDQW\LVVXEMHFWWRWKHIROORZLQJFRQGLWLRQV
%DWWHU\SDFNVDUHJXDUDQWHHGIRUDWKUHH\HDUSHULRGRQO\
7KHWRROKDVQRWEHHQPLVXVHGDEXVHGQHJOHFWHGDOWHUHGPRGL¿HGRUUHSDLUHGE\DQ\RQHRWKHU
than an authorized service center.
2QO\SURSHUDFFHVVRULHVDQGSDUWVKDYHEHHQXVHGRQRUZLWKWKHSURGXFW
7KHWRROKDVEHHQVXEMHFWHGWRIDLUZHDUDQGWHDU
7KHWRROKDVQRWEHHQXVHGIRUUHQWDOSXUSRVHV
7KHWRROKDVQRWVXVWDLQHGGDPDJHWKURXJKIRUHLJQREMHFWVVXEVWDQFHVRUDFFLGHQWV
6DOHVUHFHLSWPXVWEHSUHVHQWHGDVSURRIRIRULJLQDOSXUFKDVH
<RXUZDUUDQW\GRHVQRWFRYHU
&RPSRQHQWVWKDWDUHVXEMHFWWRQDWXUDOZHDUDQGWHDUFDXVHGE\XVHLQDFFRUGDQFHZLWKRSHUDWLQJ
instructions.
8QDXWKRUL]HGLPSURSHUPDLQWHQDQFHKDQGOLQJRURYHUORDGLVH[FOXGHGIURPWKLVZDUUDQW\DVDUH
accessories such as bulbs, blades and bits, etc.
This guarantee statement does not replace but is in addition to your statutory rights.
This warranty does not apply to accessories supplied with the tool.
This warranty applies only to the original purchaser and may not be transferred.
All repairs and replacement tools will be covered by the limited warranty for the balance of the warranty
period from the date of the original purchase.
REPLACEMENT PARTS LIST
For replacement parts, call our customer service department at 1-888-3KOBALT, 8 a.m. - 8 p.m., EST,
Monday – Friday.
PART DESCRIPTION PART #
112 V Battery 70039758
212 V Battery Charger 70039757
3Belt Hook 70039746
4Bit Holder 70039754
5Screw for Hook & Bit
Holder
70039747