Kobold Heinrichs V31 User manual

Heinrichs Messtechnik GmbH
Operating Manual V31
June 2022
Variable Area Flowmeter
V31
Operating Instructions
Please read the instruction manual and keep them in a safe place!

Heinrichs Messtechnik GmbH
Page 2
Operating manual V31
Table of Contents
Operating Instructions 1
Introduction 4
I. Shipping and storage; product inspection 4
II. Warranty 4
III. Maintenance, Repair and Hazardous substances 4
IV. Disposal 4
V. Supplementary operating instructions 4
VI. Operating manual of explosion-proof flowmeters 4
1. Steps Prior to Operation 5
2. Safety Advisories 6
2.1 Installation, Commissioning, Operating Personnel 6
2.2 Hazard Warnings 6
2.3 Proper Use of the Device 6
2.4 Installation and servicing 7
2.5 Returning your flowmeter for servicing or calibration 8
3. Identification 9
3.1 Designation / Rating Plate 9
4. Operating Principle and System Configuration 11
4.1 System Design 12
4.1.1 Construction / dimensions 12
4.1.2 Materials 13
4.2 Float Types 14
4.3 Contacts 14
4.3.1 Dimensions of the assembled GSG contacts [mm] 15
4.3.2 Mounting of the GSG limit switch series 15
4.3.3 Adjusting and wiring of the limit switches 16
4.3.4 Wiring diagrams of the limit switches 17
5. Specifications 18
5.1 Mechanical Data 18
5.2 Measuring Ranges 19
5.2.1 Water 19
5.2.2 Air 20
5.3 Specifications –limit switches 21
5.3.1 GSGA –limit switches 21
5.3.2 GSGB –limit switches 21
5.3.3 GSGW –limit switches 22
6. Installation and Condition for use 23
6.1 Operating Conditions / Installation 23
6.1.1 Installation conditions 23
6.1.2 Start-up 23
6.1.3 Pumps 23
6.1.4 Installation 23
6.1.5 Gas metering 23
7. Maintenance 23

Heinrichs Messtechnik GmbH
Operating manual V31
Page 3
8. CE / UKCA Marking 24
9. Order Information 24
9.1 Basic data 24
9.2 Available accessories 24
10. Model Code V31 25
11. Declaration of Decontamination 30
12. Declaration of Conformity 31
12.1 EU Declaration of Conformity 31
12.2 UKCA Declaration of Conformity 34

Heinrichs Messtechnik GmbH
Page 4
Operating manual V31
Introduction
I. Shipping and storage; product inspection
Shipping and Storage
The device is to be safeguarded against moisture, dirt (especially the meters internal), impact and
damage. The storage temperature limits are to be observed. Depending on the device size the area
flowmeters float may be secured. This transport protection must be removed before the device is
installed.
Product inspection
Upon receipt of the product, the consignment should be checked for completeness. The data of the
device have to be compared with the packing slip and the order documents
Notify us of any shipping damage immediately upon receipt of the product. Any damage claim
received at a later time will not be honoured.
II. Warranty
Your flow meter was manufactured in accordance with the highest quality standards and was
thoroughly tested prior to shipment. However, in the event any problem arises with your device, we
will be happy to resolve the problem for you as quickly as possible under the terms of the warranty
which can be found in the terms and conditions of delivery. Your warranty will only be honoured if
the device was installed and operated in accordance with the instructions for your device. Any
mounting, commissioning and/or maintenance work is to be carried out by qualified and authorized
technicians only.
III. Maintenance, Repair and Hazardous substances
When used in the intended manner no special maintenance is required. However, the flowmeter
should be checked within the context of routine maintenance of the facility and the pipelines. Should
a repair, calibration or maintenance become necessary, be sure to clean the device thoroughly and
follow the steps in section 2.5 “Returning your flowmeter for servicing or calibration” on page 8
before returning the device to Heinrichs Messtechnik. The operator is liable for any substance
removal or personal damage costs arising from inadequate cleaning of a device sent for repair.
IV. Disposal
Observe the regulations applicable to disposal in the country of installation!
V. Supplementary operating instructions
Supplement operating manuals are available for special features, interfaces and operations relating
to your device, request your copy from our service department.
VI. Operating manual of explosion-proof flowmeters
For installation of the flowmeter within hazardous areas read the operation manual of explosion-
proof flowmeters. It contains all the EX-relevant information for your flowmeter.
Warning
Only devices designated as EX-certified on their rating plates may be used in
areas of potentially explosive atmospheres!
The use of standard equipment in EX-hazardous areas is strictly prohibited.

Heinrichs Messtechnik GmbH
Operating manual V31
Page 5
1. Steps Prior to Operation
These montage and operating instructions are provided to help aid in the correct
installation as well as for the operation and maintenance of the meter. It is
essential that you read these operating instructions before installing and
operating the device. The device is to be installed and serviced by a qualified
technician only. Special designs and applications are not included in this manual.
Downloading of the present document from our web site www.heinrichs.eu and
printing out this document is allowed only for the purposes of using our mass
flowmeters. All rights reserved. No instructions, wiring diagrams, and/or supplied software, or any
portion thereof, may be produced, stored, in a retrieval system or transmitted by any means,
electronic, mechanical, photocopying or otherwise, without the prior written permission of Heinrichs
Messtechnik GmbH.
Although the materials in the present document were prepared with extreme care, errors cannot be
ruled out. Hence, neither the company, the programmer nor the author can be held legally or
otherwise responsible for any erroneous information and/or any loss or damage arising from the use
of the information enclosed.
Heinrichs Messtechnik GmbH extends no express or implied warranty concerning the applicability
of the present document for any purpose other than that described.
We plan to optimize and improve the products described and in so doing will incorporate not only
our own ideas but also, and in particular, any suggestions for improvement made by our customers.
If you feel that there is any way in which our products could be improved, please send your
suggestions to the following address:
Heinrichs Messtechnik GmbH
HM-EE (R&D Department)
Robert-Perthel-Strasse 9
D-50739 Cologne
Germany
or:
via fax : [phone]
via email: [email protected]
Note
We reserve the right to change the technical data in this manual in the light of
any technical progress that might be made.
For updates regarding this product, visit our website at www.heinrichs.eu,
where you will also find contact information for the Heinrichs Messtechnik
distributor nearest you. For information regarding our own sales operations,
contact us at [e-mail].

Heinrichs Messtechnik GmbH
Page 6
Operating manual V31
2. Safety Advisories
2.1 Installation, Commissioning, Operating Personnel
The present document contains the information that you need in order to operate the product
described herein properly. This document is intended for use by qualified personnel. This means
personnel who are qualified to operate the device described herein safely, including
electronics engineers,
electrical engineers, or
service technicians
who are conversant with the safety regulations pertaining to the use of electrical and automated
technical devices and with the applicable laws and regulations in their own country.
Such personnel must be authorized by the facility operator to install, commission and service the
product described herein, and must have read and understood the contents of this operating
instructions before working with the device.
2.2 Hazard Warnings
The purpose of the hazard warnings listed below is to ensure that device operators and maintenance
personnel are not injured and that the flow meter and any devices connected to it are not damaged.
The safety advisories and hazard warnings in the present document that aim to avoid placing
operators and maintenance personnel at risk and to avoid material damage are prioritized using the
terms listed below, which are defined as follows in regard to these instructions herein and the
advisories pertaining to the device itself:
Warning
Caution
Note
means that failure to take the
prescribed precautions
could result in injury,
substantial material damage
or even death. Always
comply to these warnings
and proceed with caution.
means that failure to take the
prescribed precaution could
result in material damage or
destruction of the device. We
advice always to abide to
these instructions!
means that the
accompanying text contains
important information about
the product, handling the
product or about a section of
the documentation that is of
particular importance.
2.3 Proper Use of the Device
The Coriolis Mass Flow Sensor is intended for the sole use of direct and continuous mass flow
measurement of liquids and gases.
To ensure safety for people and the environment adhere to the installation and operational
instructions and warning in this manual.

Heinrichs Messtechnik GmbH
Operating manual V31
Page 7
Warning
The operator is responsible for ensuring that the material used in the sensor
and housing are suitable and that such material meets the requirements for the
process medium and the ambient site conditions.
The manufacturer accepts no responsibility for the selection of unsuitably
materials.
Warning
Before using the meter with corrosive or abrasive media, the operator must
check the suitability of all materials that come into contact with the media. In
the case of special media, including cleaning media, we will be happy to help
you check the corrosion resistance of materials. However, since small changes
in the process temperature, concentration or the degree of contamination can
result in changes in the corrosion resistance, the full responsibility must remain
with the operator.
Caution
To ensure the device performs correctly and safely, it must be shipped, stored,
set up, mounted, operated and maintained correctly.
2.4 Installation and servicing
The devices described in this manual are to be installed and serviced only by qualified technical
personnel such as a qualified Heinrichs Messtechnik electronics engineer or service technician.
Heinrichs Messtechnik GmbH accepts no liability for any loss or damage of any kind arising from
improper operation of any product, improper handling or use of any replacement part, or from
external electrical or mechanical effects, overvoltage or lightning. Any such improper
operation, use or handling shall automatically invalidate the warranty for the product
concerned.
In the event a problem arises with your device, or if you need assistance in diagnosing a problem
with your device, please contact us at one of the following numbers to arrange to have your device
repaired:
[phone] [phone]

Heinrichs Messtechnik GmbH
Page 8
Operating manual V31
2.5 Returning your flowmeter for servicing or calibration
Before sending your flowmeter back to us, for servicing or calibration, make sure it is completely
clean. Any residues of substances that could be hazardous to the environment or human health are
to be removed from all crevices, recesses, gaskets, and cavities of the housing before the device is
shipped.
Warning
The operator is liable for any loss or damage of any kind, including personal
injury, decontamination measures, removal operations and the like that are
attributable to inadequate cleaning of the device.
Any device sent in for servicing is to be accompanied by a „Declaration of
Decontamination“a template of which is provided in section 11 on page 30.
When returned, the device is to be accompanied by a document describing the problems
encountered. Please include in this document the name of a contact person whom our technical
service department can contact to enable us to repair your device as expeditiously as possible and
minimize the repair costs.

Heinrichs Messtechnik GmbH
Operating manual V31
Page 9
3. Identification
Manufacturer:
Heinrichs Messtechnik GmbH
Robert-Perthel-Strasse 9
D-50739 Cologne
Germany
Phone: [phone]
Fax: [phone]
Internet: www.heinrichs.eu
Email: [e-mail]
Product type:
Variable area flow-meter
Product
name:
V31
File name:
V31_BA_22.01_EN
Version:
22.01
Publish date
21.06.2022
3.1 Designation / Rating Plate
The device and its specifications are presented as a model-code on the rating plate. The model-
code consists of the prefix “V31” followed by an alpha-numerical code.
Refer to section 11 “Model Code V31” for a description of each position.
Example of a V31 rating plate.
Application
The V31 variable area flow-meter is used for the flow metering of transparent liquid and gas media
in pipes. The scale on the device indicates the flow rate expressed as a volume or mass per unit of
time. Standard scales are available for liquids with a density of 1kg/l (62.43 lb/ft3). The scales must
be recalculated for all other media depending on the physical characteristics.
The flow tube is optionally available with percentage or 2 mm (0.078 inch) scaling.
Applications: Flow metering, dosing, monitoring and control of liquid or gas media. For the
purpose of process monitoring, the device can be fitted with one or more limit
switches.
Contact Information Importer

Heinrichs Messtechnik GmbH
Page 10
Operating manual V31
Warning
The device is of limited use for the metering of potentially hazardous liquids
and gases. It is essential that the operator takes appropriate steps to ensure
that in the event of a glass tube breakage, no personnel are harmed and no
equipment is damaged. The system operator is legally responsible for any
effects provoked by operation of the device
Warning
Only devices marked as Ex-devices on their rating plates may be used in EX
hazardous locations. Standard equipment is not permitted for installation and
operation in EX hazardous locations.
For installation within hazardous areas read the Ex-supplementary manual
available at www.heinrichs.eu. It contains all EX-relevant parameters for the
V31 flow-meter.

Heinrichs Messtechnik GmbH
Operating manual V31
Page 11
4. Operating Principle and System Configuration
The measuring instrument composes of a float and a conical
glass tube (M)
A medium flows from the bottom to the top through the
measuring ring, lifting the float in the process until the
buoyancy force (A) and the weight of the float (Gs) establish
equilibrium. As the height of the float varies, an annular
clearance (S) proportional to the flow appears between the
float and the measuring tube. The height of the float (K) in the
measuring tube serves as the actual rate of the flow. The flow
rate is read directly from the scale.
The readings obtained apply solely to the medium for which the
device has been calibrated or for a medium with the same
density and viscosity as the calibration medium.
The float may also be optionally guided by a float guide rod.
This option is recommended to increase the operational safety
and to protect against glass breakage in particular operating
environments, with the use of solenoid valve controls.
Bei certain levels of viscosity guided floats are essential. This
option however cannot be combined with floats containing
magnets or with PVDF coated floats.
For signalling specific flow rates, the variable area flowmeter
can be outfitted with limit switches. This option is only available
with floats which possess mounted magnets.

Heinrichs Messtechnik GmbH
Page 12
Operating manual V31
4.1 System Design
4.1.1 Construction / dimensions
V31
Sensor
Connection
Model
ØAR
a
b
SW1
SW2
Thread
Hose connector
Flange
G / NPT
Inner
Diameter
DN EN1092-1
Form B1, PN40
ASME B16.5-2003
RF, Class 150
S04
Ø33,7
19
235
39
24
1/4", 3/8“, 1/2"
Ø13, Ø17
10/15/20/25
1/2", 3/4", 1”
S05
S06
Ø60,3
38
235
67
46
3/4”, 1”
Ø19, Ø25, Ø38
25/40
1”, 1½”
S07
Ø88,9
58
235
100
65
1¼”, 1½”, 2”
Ø50
40/50/65
1½”, 2”, 2½”
Weights
Connection thread
Connection Flange
S04
G 1/2“
0,7 kg
DN 15
2,0 kg
S05
G 1/2"
0,7 kg
DN 15
2,0 kg
S06
G 1“
2,0 kg
DN 25
3,9 kg
S07
G 1“
4,0 kg
DN 50
8,9 kg

Heinrichs Messtechnik GmbH
Operating manual V31
Page 13
4.1.2 Materials
Item
Pieces
Description
Material
1
1
Enclosure
1.4301
2
1
Measuring tube
Borosilicate glass
3
2
Float Stop
PVDF
4
1
Float
1.4571, AL, PVDF
5
2
O-ring
EPDM, Viton, FEP/FFKM
6
2
O-ring
EPDM, Viton, FEP/FFKM
7
2
Union nut
AL, Stainless Steel
8
2
Flange
Stainless Steel
9
2
Flange
PVDF
10
2
Threaded Connection
PVDF, Stainless Steel
11
2
Hose Connector
PVDF, Stainless Steel
12
2
Bonded Connection
PVC

Heinrichs Messtechnik GmbH
Page 14
Operating manual V31
4.2 Float Types
There are three types of floats on offer:
A. Float without guide rod
B. Guided float
C. Viscosity stabile floats
The following viscosity limits require a viscosity-stable
float:
Model
Viscosity (mPas, cP)
S05
≥ 3
S06
≥ 5
S07
≥ 8
4.3 Contacts
The bi-stable magnetic contacts GSGA, GSGB and GSGW serve to indicate the position of the float,
thus indicating the measured value in a non-reactive, contact-free means.
Features:
Bi-stable behaviour
Available as normally open, normally closed or change-over
No power required for operation
High vibration resistance
Non-reactive switching
No interaction between the contact
Simple plug-in connector
Float Reading Edge

Heinrichs Messtechnik GmbH
Operating manual V31
Page 15
4.3.1 Dimensions of the assembled GSG contacts [mm]
4.3.2 Mounting of the GSG limit switch series

Heinrichs Messtechnik GmbH
Page 16
Operating manual V31
4.3.3 Adjusting and wiring of the limit switches
When ordered, the limit switches are factory set at the ordered values. They can however be
adjusted to suit the operators requirements.
For re-adjusting an M4 nut (SW7) must be released until the clamping position can be adjusted. Now
the limit switch can be slid into an it’s new position. After the switch has been positioned, tighten
the nut /SW7) until the contact clamp is secured in place.
Cable mounting and wiring:
1. Unscrew Knurled locking screw (3) to
remove the M12 connector housing
from the magnetic field sensor (1)
2. Unscrew Knurled locking screw (4) to
remove the main connector housing
from the connector head (5)
3. Unscrew cable connection (8) using an
spanner (across flats 13) from the main
enclosure and remove sealing inserts
(6, 7).
4. Feed connection cable Ø 4-6 mm
through the cable connection (8) and
insert sealing insert (6, 7) into the main
enclosure (5).
Remove the cables outer insulation
and the wire strands insulation at the
required length and affix ferrules to
each wire strand. Finally wire-up to the
terminals of the connector head (4)
according to the wiring diagram.
5. The reassembly of the connector is
performed in reverse order.
Be careful when connecting the
Knurled locking screw (3) to the thread
of the sensor (2) not to tilt the housing
so not to damage the thread of the
M12 enclosure.
6. The enclosure (5) can be mounted in
any direction so that the cable –after
plugging –can be guided either to the
left, the right, the top or the bottom.
Caution
Please note that the seal of the cable gland is correctly seated on the jacket of
the cable! Tighten the cable gland firmly!
Before commissioning, we recommend that the float is manually passed by the contact.
By this means, the correct start position of the contact can be ensured.

Heinrichs Messtechnik GmbH
Operating manual V31
Page 17
4.3.4 Wiring diagrams of the limit switches
Figure 1: Electrical connection GSGA
Figure 2: Electrical connection GSGB
Figure 3: Electrical connection GSGW
Figure 4: Pin assignment of the M12 connector

Heinrichs Messtechnik GmbH
Page 18
Operating manual V31
5. Specifications
5.1 Mechanical Data
Measuring Range
Turndown Ratio
1:10
Smallest Measuring
Range
Water
3-30 l/h
Air*
36-360 Nl/h
Largest Measuring Range
Water
1.000-10.000 l/h
Air*
18.000-180.000 Nl/h
*) Referred to 0 °C and 1,013 bar abs.
Accuracy Class
(acc. VDE/VDI 3513,
sheet 2)
Liquid
1,6 %
Gas
2,5 %
qG50 %
Flow Direction
From bottom to top
Materials
Measuring Tube
Borosilicate glass
Connections
1,4571, PVDF, PVC
Float
1.4571, Aluminium 3.1645, PVDF
Float Guide
1.4571
Gaskets
Viton, EPDM, FEP/FFKM
Float Stop
PVDF / Stainless Steel
Sensor Body
1.4301
Shatter Protection
Plexiglas® GS
Anzeige
Measuring Range, Process Information
Ambient Conditions
Ambient Temperature
-20 … +80 °C (-4…+176 °F)
Ambient Temperature
PVC
-10 … +50 °C (+14 … +122 °F)
Storing Temperature
-20 … +60 °C (-4 … +140 °F)
Climate Classification
Weatherproof and/or unheated operation site, class C according
to DIN IEC 654 part 1
Shock/Vibration
Resistance
The device should be protected against extreme shock and
vibration, either of which could cause damage.
Process Conditions
Pressure Resistance
Ranges B1 to C7
max. 15 bar (at max. 80 °C / 176 °F)
Ranges D1 to D8
max. 10 bar (at max. 80 °C / 176 °F)
Ranges E1 to E5
max. 6 bar (at max. 80 °C / 176 °F)
Connections in PVDF / PVC
max. 10 bar (at max. 20 °C / 68 °F)
max. 4 bar (at max. 40 °C / 104 °F)
max. 2,5 bar (at max. 50 °C / 122
°F)
Media Temperature
Float: 14571 / Alu
-10 … +80 °C (+14 … +176 °F)
Float: PVDF
-10 … +80 °C (+14 … +176 °F)
Adhesive connection: PVC
-10 … +50 °C (+14 … +122 °F)
Media State
Liquid or gaseous
Density
Liquid
≤ 2,0 kg/l
Gas
- / -
Inlet and Outlet sections
Inlet and outlet sections are not required as long as the flow profile is laminar. On strongly non
laminar flow profiles e.g. regulating and shutoff devices inlet straight of 250 mm, see also
directive VDI/VDE 3513
Pressure Loss
See measuring ranges

Heinrichs Messtechnik GmbH
Operating manual V31
Page 19
5.2 Measuring Ranges
5.2.1 Water
Standard measurement ranges for liquid with density = 1 kg/l (62,43 lb/ft3) and Viscosity 1 mPas.
V31 Model
Measuring
Range code
Pressure
Loss.
Float 1.4571
with and without
Guide rod.
Float 1.4571 with
Magnet.
Float 1.4571
Viscosity
stabilised
Float PVDF
weighted with
Magnet.
[mbar] / [psi]
[l/h]
[l/h]
[l/h]
[l/h]
S04
B1W
10 / 0,145
3 - 30
n.v.
n.v.
1,1 - 11
B2W
4 - 40
n.v.
n.v.
1,5 - 15
B3W
5 - 50
n.v.
n.v.
2 - 20
B4W
6,5 - 65
n.v.
n.v.
2,5 - 25
B5W
8 - 80
n.v.
n.v.
3,2 - 32
B6W
10 - 100
n.v.
n.v.
4 - 40
S05
C1W
20 / 0,290
12,5 - 125
12 - 120
10 - 100
6,5 - 65
C2W
16 - 160
15 - 150
12,5 - 125
9 - 90
C3W
20 - 200
18 - 180
16 - 160
11 - 110
C4W
25 - 250
24 - 240
20 - 200
14 - 140
C5W
40 / 0,580
31,5 - 315
30 - 300
24 - 240
17,5 - 175
C6W
40 - 400
36 - 360
30 - 300
22 - 220
C7W
50 - 500
48 - 480
36 - 360
25 - 250
S06
D1W
19 / 0,280
40 - 400
40 - 400
n.v.
32 - 320
D2W
65 - 650
60 - 600
40 - 400
50 - 500
D3W
80 - 800
75 - 750
50 - 500
60 - 600
D4W
100 - 1000
95 - 950
60 - 600
75 - 750
D5W
120 - 1200
120 - 1200
75 - 750
100 - 1000
D6W
24 / 0,350
160 - 1600
150 - 1500
100 - 1000
125 - 1250
D7W
200 - 2000
180 - 1800
120 - 1200
160 - 1600
D8W
33 / 0,480
250 - 2500
240 - 2400
140 - 1400
200 - 2000
D9W
300 - 3000
280 - 2800
180 - 1800
240 - 2400
S07
E1W
25 / 0,360
400 - 4000
380 - 3800
250 - 2500
320 - 3200
E2W
500 - 5000
480 - 4800
300 - 3000
380 - 3800
E3W
650 - 6500
640 - 6400
400 - 4000
500 - 5000
E4W
800 - 8000
750 - 7500
450 - 4500
640 - 6400
E5W
1000 - 10000
950 - 9500
550 - 5500
750 - 7500

Heinrichs Messtechnik GmbH
Page 20
Operating manual V31
5.2.2 Air
Standard measurement ranges for air at Pabs = 1,013 bar (14,69 psi), T = 20 °C (68 °F), Density =
1,293 kg/m³, Viscosity = 0,0181 mPas
V31 Model
Measuring
Range code
Pressure
Loss.
Float Aluminium
with and without
Guide rod.
Float Aluminium
with Magnet.
Float PVDF
Float PVDF
weighted with
Magnet.
[mbar] / [psi]
[Nl/h]
[Nl/h]
[Nl/h]
[Nl/h]
S04
B1L
4 / 0,058
5 - 500
-
36 - 360
-
B2L
65 - 650
-
50 - 500
-
B3L
80 - 800
-
65 - 650
-
B4L
110 - 1100
-
80 - 800
-
B5L
140 - 1400
-
100 - 100
-
B6L
160 - 1600
-
125 - 1250
-
S05
C1L
6,5 / 0,094
200 - 2000
250 - 2500
150 - 1500
200 - 2000
C2L
300 - 3000
320 - 3200
200 - 2000
300 - 3000
C3L
360 - 3600
400 - 4000
250 - 2500
360 - 3600
C4L
400 - 4000
500 - 5000
300 - 3000
450 - 4500
C5L
15 / 0,218
500 - 5000
640 - 6400
360 - 3600
600 - 6000
C6L
640 - 6400
800 - 8000
500 - 5000
700 - 7000
C7L
800 - 8000
1000 - 10000
550 - 5500
950 - 9500
S06
D1L
7 / 0,102
750 - 7500
850 - 8500
520 - 5200
750 - 7500
D2L
1000 - 10000
1200 - 12000
800 - 8000
1000 - 10000
D3L
1300 - 13000
1500 - 15000
900 - 9000
1300 - 13000
D4L
1600 - 16000
2000 - 20000
1200 - 12000
1600 - 16000
D5L
2000 - 20000
2400 - 24000
1500 - 15000
2000 - 20000
D6L
9 / 0,131
2800 - 28000
3200 - 32000
2000 - 20000
2800 - 28000
D7L
3600 - 36000
4000 - 40000
2500 - 25000
3600 - 36000
D8L
12 / 0,174
4000 - 40000
5000 - 50000
3000 - 30000
4000 - 40000
D9L
5000 - 50000
6000 - 60000
3600 - 36000
5000 - 50000
S07
E1L
10 / 0,145
6400 - 64000
7500 - 75000
5000 - 50000
6400 - 64000
E2L
8000 - 80000
10000 - 100000
6500 - 65000
8000 - 80000
E3L
10000 - 100000
12500 - 125000
8000 - 80000
10000 - 100000
E4L
14000 - 140000
15000 - 150000
10000 - 100000
14000 - 140000
E5L
16000 - 160000
18000 - 180000
12500 - 125000
16000 - 160000