Kobold Heinrichs HPC User manual

OPERATING MANUAL FOR
HPC EXPLOSION-PROOF FLOW METERS
Page 1 of 21
Coriolis mass flow
sensors
HPC
Supplementary Operating Manual for explosion-proof
Flow-sensors
Please read the instructions carefully and store them in a safe place

Page 2 of 21
OPERATING MANUAL FOR
HPC EXPLOSION-PROOF FLOW METERS
CONTENTS
INTRODUCTION.............................................................................................................3
1STEPS PRIOR TO OPERATION ..............................................................................4
1.1 Installation, mounting, commissioning and maintenance................................................ 4
1.2 Hazard warnings............................................................................................................ 4
1.2.1 Danger .................................................................................................................... 5
1.2.2 Warning................................................................................................................... 5
1.2.3 Caution.................................................................................................................... 5
1.2.4 Note......................................................................................................................... 5
1.3 Proper use of the device................................................................................................ 5
2IDENTIFICATION......................................................................................................6
2.1 Version / date................................................................................................................. 6
3SPECIFICATIONS.....................................................................................................7
3.1 Description of the HPC Mass-Flow Sensor .................................................................... 7
3.2 Device identification....................................................................................................... 7
3.2.1 HPC rating plates .................................................................................................... 7
3.3 Mounting and Installation............................................................................................... 8
3.3.1 Thermally insulated sensor...................................................................................... 8
3.3.2 Heated sensor......................................................................................................... 8
3.3.3 Connection sensor –transmitter.............................................................................. 8
3.4 EC Type-Examination...................................................................................................10
3.4.1 Sensor Parameters.................................................................................................10
3.4.2 Ambient temperature range Ta...............................................................................11
3.5 Connecting the sensor to a transmitter .........................................................................11
3.5.1 Connecting cables..................................................................................................11
3.5.2 Equipotential bonding.............................................................................................11
4INSTALLATION AND COMMISSIONING................................................................12
4.1 Mounting.......................................................................................................................12
4.2 General conditions for safe operation ...........................................................................12
4.3 Requirements for installation in all environments..........................................................12
4.4 Requirements for installation dust environments...........................................................13
4.5 Ex relevant screw and bolt torques ...............................................................................13
5MAINTENANCE AND REPAIR WORK ...................................................................14
5.1 Definition of terms according to IEC 60079-17:.............................................................14
5.2 Fault elimination............................................................................................................15
5.3 Disposal........................................................................................................................15
6MODEL CODE.........................................................................................................16
7RELEVANT STANDARDS FOR HAZARDOUS LOCATIONS.................................17
7.1 ATEX............................................................................................................................17
7.2 IECEx............................................................................................................................17
8DECLARATION OF CONFORMITY........................................................................18

OPERATING MANUAL FOR
HPC EXPLOSION-PROOF FLOW METERS
Page 3 of 21
Introduction
I Shipping and storage
The device is to be safeguarded against moisture, dirt, impact and damage.
II Product inspection
Upon receipt of the product, the consignment should be checked for completeness. The data
of the device have to be compared with the packing slip and the order documents
Notify us of any shipping damage immediately upon receipt of the product. Any damage claim
received at a later time will not be honoured.
III Warranty
Your flow sensor was manufactured in accordance with the highest quality standards and was
thoroughly tested prior to shipment. However, in the event any problem arises with your
device, we will be happy to resolve the problem for you as quickly as possible under the terms
of the warranty which can be found in the terms and conditions of delivery. Your warranty will
only be honoured if the device was installed and operated in accordance with the instructions
for your device. Any mounting, commissioning and/or maintenance work is to be carried out
by qualified and authorized technicians only.
IV Validity of this operating manual
The present instructions apply to explosion-proof Coriolis flow sensors of the
HPC series, as of year of construction November 2018 or later and serial
number 340000 or higher. These instructions are supplementary operating
manual for non-explosion proof Coriolis flow sensors. If you do not have a copy
of the latter instructions, please request one from Heinrichs Messtechnik GmbH
or download the instructions from our website.
The instructions herein pertain primarily to explosion proof Coriolis flow sensors for use in
conjunction with an explosion proof certified transmitter. The technical data in the mounting
and operating instructions for non-explosion proof Coriolis flow sensors still apply insofar as
the present instructions do not replace them or exclude their application.
The transmitter used in conjunction with an HPC sensor must be listed for use in its country of
installation. The manufactures installation drawings shall be followed when installing.
V Repairs and hazardous materials
It is important that you do the following before shipping your flow sensor to Heinrichs
Messtechnik GmbH for repair:
Enclose a description of the problem with your device. Describe in as much detail as
possible the application and the physical and chemical properties of the fluid.
Remove any residues from the device and be sure to clean the seal grooves and recesses
thoroughly. This is particularly important if the fluid is corrosive, toxic, carcinogenic,
radioactive or otherwise hazardous.
The operator is liable for any substance removal or personal damage costs arising from
inadequate cleaning of a device that is sent for repair.

Page 4 of 21
OPERATING MANUAL FOR
HPC EXPLOSION-PROOF FLOW METERS
1 Steps prior to operation
Prior to installation and operation, it is essential that the operator
familiarizes himself with all of the instructions and information contained in
the manual for non-explosion proof Coriolis flow meters as well as the
present instructions. If any part of either manual is missing, contact
Heinrichs Messtechnik GmbH to request a new manual. These manuals
can also be downloaded from our website.
The HPC sensors described herein are only to be used to measure mass and volume flow, as
well as liquid and gas density and temperature, in conjunction with a transmitter certified for
use in the area and country of operation.
1.1 Installation, mounting, commissioning and maintenance
Installation, mounting, commissioning and maintenance are to be performed by a technician
trained to work with explosion-proof devices, or by a Heinrichs Messtechnik service
technician.
Warning
Any safety relevant maintenance or repairs in terms of explosion-protection is to be
carried out by the manufacturer, an authorized Heinrichs Messtechnik GmbH
service centre or under the supervision of an expert in explosion proof devices.
Heinrichs Messtechnik GmbH accepts no liability for any loss or damage of any kind arising from
improper operation of any product, improper handling or use of any replacement part, or from
external electrical or mechanical effects, overvoltage or lightning. Any such improper operation,
use or handling shall automatically invalidate the warranty for the product concerned.
In the event of a problem please contact the service centre of Heinrichs Messtechnik:
Phone:[phone]
Fax: [phone]
Contact our customer service department if your device needs repair or if you need assistance
in diagnosing a problem with your device.
1.2 Hazard warnings
The purpose of the hazard warnings listed below is to ensure the safety of operators and
maintenance personnel as well as safeguarding the flow meter and any devices connected to
it from damage.
The safety advisories and hazard warnings in this document which aim to avoid placing
operators and maintenance personnel at risk, as well as avoiding material damage, are
emphasised using the terms listed below. The used terms, within these instructions as well as
upon the device itself, are defined as follows.

OPERATING MANUAL FOR
HPC EXPLOSION-PROOF FLOW METERS
Page 5 of 21
1.2.1 Danger
Means that failure to take the prescribed precautions will result in death, severe bodily injury,
or substantial material damage.
1.2.2 Warning
Means that failure to take the prescribed precautions could result in death, severe bodily
injury, or substantial material damage.
1.2.3 Caution
Means that light bodily injury or damage to assets can occur if the precaution is ignored.
1.2.4 Note
means that the accompanying text contains important information about the product, handling
of the product or is about a section of the documentation that is of particular importance.
1.3 Proper use of the device
Warning
The operator is responsible for ensuring that the materials used in the sensor
and transmitter housing are suitable and that such material meets the
requirements for the fluid being measured as well as the ambient site
conditions. The manufacturer accepts no responsibility in regard to such
material and housing.
Warning
For the device to perform correctly and safely, it must be shipped, stored,
mounted, operated and maintained correctly.

Page 6 of 21
OPERATING MANUAL FOR
HPC EXPLOSION-PROOF FLOW METERS
2 Identification
Manufacturer
Heinrichs Messtechnik GmbH
Robert-Perthel-Strasse 9
D-50739 Cologne
Phone: [phone]
Fax: [phone]
Internet: http://www.heinrichs.eu
E-mail: [email protected]
Product type
Mass flow Sensor for liquid and gaseous products
Product name
HPC-0x
Coriolis mass flow sensors
2.1 Version / date
Version: HPC_EX_BA_02_EN
Dated: 17/01/2020 (dd.mm.yyyy)

OPERATING MANUAL FOR
HPC EXPLOSION-PROOF FLOW METERS
Page 7 of 21
3 Specifications
3.1 Description of the HPC Mass-Flow Sensor
The HPC sensor has an “Intrinsic safety” type of protection and is equipped with the following
four independent potential-free and isolated circuits:
Excitation circuit
Sensor circuit 1
Sensor circuit 2
Temperature sensor circuit (RTD)
All circuits have safe separation from one another within the sensor
The transmitter shall be connected to the sensor using a dedicated cable specially designed
for this purpose. Such a cable can be purchased from Heinrichs Messtechnik during your
order process.
Although the appearance of the standard and explosion-proof transmitters is often very similar
in appearance and their rating plates contain similar information, under no circumstances
should a standard (non-explosion proof) transmitter be connected to an explosion-
proof sensor!
3.2 Device identification
The rating plates on Heinrichs Messtechnik flow meters that are suitable for use in potentially
explosive atmospheres are labelled accordingly. Since the sensor and transmitter are
separately certified, each device has its own rating plate.
3.2.1 HPC rating plates
The HPC rating plates contain all the information necessary to identify the sensor, and for
determining it’s suitability for a potential explosive atmosphere.
Image 1: HPC for process temperatures ranging from –40 °C to 80 °C.
Image 2: HPC for process temperatures ranging from –40 °C to 180 °C

Page 8 of 21
OPERATING MANUAL FOR
HPC EXPLOSION-PROOF FLOW METERS
3.3 Mounting and Installation
The mounting instructions for the standard sensor also apply to the explosion-proof sensor.
3.3.1 Thermally insulated sensor
In explosive atmospheres the sensor may also be outfitted with thermal insulation. However,
so not to impair the sensors thermal ratings, the sensors neck cooling ribs of the high-
temperature version shall not be included in the insulation. The connector of the standard
version may be completely enveloped by the insulating material.
3.3.2 Heated sensor
The sensor can be externally heated to avoid crystallization in the flow tube. Any heating
technique or device can be used. When using electrical heating devices, these must be
suitable for use in the potentially explosive environment present.
It is the operator’s responsibility to ensure that the heating temperature does not
exceed the maximum allowable temperature for the fluid and/or the maximum allowable
temperature range for the potentially explosive atmosphere in which the device is
being operated.
The maximum allowable temperature range for the fluid is indicated on the sensors rating
plate. It is also the operator’s responsibility to ensure that no hazards are created by hot
surfaces pursuant to EN 1127-1 (Explosive atmospheres –Explosion prevention and
protection) paragraphs 5.2 and 6.4.2.
3.3.3 Connection sensor –transmitter
The dedicated cable SLI2Y (SP) CY 5 x 2 x 0.5 mm² [blue] is to be used for the electrical
connection between sensor and the remote mounted transmitter. This cable, which is
available from Heinrichs Messtechnik, has five twisted wire pairs, each of which has a foil
shield, and a tinned copper strand wound around each pair. These tinned copper strands are
twisted together are installed in the “shield” terminal of the transmitter. All 5 cable pairs are
shielded by a further tinned copper wire mesh. This outer cable shield is connected to the
transmitters housing, via a dedicated EMC cable fitting, as well as to the outer-casing of the
sensor’s connector thus ensuring optimum noise immunity.
Image 2: Heinrichs standard SLI2Y (SP) CY 5 x 2 x 0.5 cable with HAN R23 connector

OPERATING MANUAL FOR
HPC EXPLOSION-PROOF FLOW METERS
Page 9 of 21
3.3.3.1 Pin assignment of the Sensor cable
Designation
Terminal / Pin designation
Type of protection
Ex ia
Sensor lines
SENSOR1 +
1
x
SENSOR1 -
2
x
SENSOR2 +
3
x
SENSOR2 -
4
x
TIk-
5
x
Temperature sensor -
6
x
Temperature sensor +
7
x
TIk+
8
x
EXCITER Coil
9
x
EXCITER Coil
10
x
Shield
Shield
x
Note: Sensor and transmitter are always mounted separately.
3.3.3.2 Cable Parameters
The operator is to comply in all cases with the applicable installation regulations such as
EN 60079-14 “Electrical apparatus for explosive gas atmospheres- Part 14: Electrical
installations in hazardous areas”.
Applicable guidelines pertaining to the interconnection of intrinsically safe circuits must also be
observed.
The following maximum cable parameters must be abided to:
CL= 100 pF/m wire to wire
CL= 170 pF/m wire to shield
LL= 700 µH/km wire to wire
LL= 500 µH/km wire to shield
Warning
If a connecting cable other than the Heinrichs Messtechnik cable is used, a
comprehensive assessment is required to ensure it fulfils all the requirements of
the applied protection classes and the area of installation.

Page 10 of 21
OPERATING MANUAL FOR
HPC EXPLOSION-PROOF FLOW METERS
3.4 EC Type-Examination
The sensors are certified with the following examination certificates:
ATEX
CML 19ATEX2096X
Standard Version
High Temperature Version
II 1G Ex ia IIC T4 Ga
II 1D Ex ia IIIC T135°C Da
or
II 1G Ex ia IIC T4 Ga
II 1D Ex ia IIIC T135°C Da
II 2D Ex ia IIIC T190°C/T240°C Db
IECEx
IECEx CML 19.0025 X
Standard Version
High Temperature Version
Ex ia IIC T4 Ga
Ex ia IIIC T135°C Da
Or
Ex ia IIC T4 Ga
Ex ia IIIC T135°C Da
Ex ia IIIC T190°C/T240°C Db
and are approved for the use in potentially explosive atmospheres. (hazardous classified
locations)
Warning
to comply with the requirements for use in explosive atmospheres, it is
essential that the maximum electrical and thermal values set forth below are
observed.
3.4.1 Sensor Parameters
3.4.1.1 Exciter circuit (Pins 9 and 10)
Voltage Ui 30 V
Current Ii 90 mA
Power Pi 0.4 W
Effective internal capacitance Ci negligible
Effective internal inductance Li 4.38 mH
3.4.1.2 Sensor circuits (Pins 1 –2 and 3 –4)
Voltage Ui DC 30 V
Current Ii 25 mA
Power Pi 0.130 W
Effective internal capacitance Ci negligible
Effective internal inductance Li 50 mH
Output voltage Uo AC 0.3 V

OPERATING MANUAL FOR
HPC EXPLOSION-PROOF FLOW METERS
Page 11 of 21
3.4.1.3 Temperature sensor circuits (Pins 5 to 8)
Voltage Ui DC 30 V
Current Ii 10 mA
Power Pi 0.04 W
Effective internal capacitance Ci negligible
Effective internal inductance Li negligible
3.4.2 Ambient temperature range Ta
The equipment’s temperature class, surface temperature and equipment protection
level are dependent upon the connection type, process temperature and ambient
temperature as follows:
Table1: Temperature Classes
Connection via
HAN R23
connector plug
Ambient temp.
range
Maximum
Process
temperature
Temperature
Class
Maximum
Surface
Temperature
EPL
Standard or high
temperature
-40°C to +60°C
80°C
T4
T135°C
Ga/Da
High temperature
With cooling rib
neck
-40°C to +60°C
130°C
T4
T190°C
Ga/Db
High Temperature
With cooling rib
neck
-40°C to +49°C
180°C
T2
T240°C
Ga/Db
3.5 Connecting the sensor to a transmitter
The transmitter used in conjunction with an HPC sensor must be listed for use in its planned
country of installation. The manufactures installation drawings shall be followed when
installing this equipment.
It is essential that the output parameters of the transmitter correspond to those of the sensor.
3.5.1 Connecting cables
The connecting cable for the sensor circuits must adhere to either the requirements of
EN 60079-14 for Europe, Section 18 of the Canadian Electrical Code for Canada or Article
NEC 504 and/or NEC 505 for USA.
3.5.2 Equipotential bonding
Equipotential bonding between the sensor and transmitter is essential and must be
established and maintained. Connection points are provided on the outside of the
sensor and transmitter for this purpose.

Page 12 of 21
OPERATING MANUAL FOR
HPC EXPLOSION-PROOF FLOW METERS
4 Installation and commissioning
4.1 Mounting
The mounting instructions for the standard sensor also apply to the explosion-proof sensor.
This handbook complements that of the standard sensor.
The sensor may only be separately installed and connected with a special sensor cable,
whereby the maximum CL and LL of the connection cable must be observed.
Refer to the standard operating manual for the connection scheme of the sensor
4.2 General conditions for safe operation
a) If the conditions described in this document are not adhered to or if there is any
inappropriate interference with the equipment, all the manufactures warranties expire.
b) Conditions described in this manual, as well as the permitted operating conditions
which have been defined for the sensor and which are stated on the rating plates must
be adhered to.
c) Appropriate measures shall be met to prevent any unintentional or inadmissible
damage to the device.
d) The operator shall ensure that the equipment is only installed in areas which comply
with the approved types of protection and environments.
e) All connected electrical equipment must be suitable for its intended use.
f) The operator shall ensure protection against lightning according to local regulations.
g) The sensor is maintenance-free. Substitution of components may impair intrinsic safety
4.3 Requirements for installation in all environments
a) The installation of the intrinsically safe circuits requires a control drawing (system
description), to be issued by the operator/erector.
b) The equipment is only to be installed and connected in a de-energized state.
c) The sensor can be installed in zone 0 as well as zone 20 or 21. The intrinsically safe
circuits are to be installed (from specialists) according to applicable regulations.
d) Equipotential bonding between the sensor and transmitter is essential to guarantee
conformity of the intrinsically safe circuits.
e) It is to be insured that the intrinsically safe circuits of the sensor cable are not laid
together with non-intrinsically safe circuits.
f) When using a connection cable other than the manufactures specified cable, the
intrinsic safety of the cable is to be validated using the cables nominal parameters.
Refer also to section 3.3.3.2 “Cable Parameters” on page 9
g) If the sensor is used at an ambient temperature below -20 °C, suitable cables are to be
used.

OPERATING MANUAL FOR
HPC EXPLOSION-PROOF FLOW METERS
Page 13 of 21
h) The operational wall thickness of the stainless steel flow tubes are < 1 mm. Therefore,
in cases where the sensor is operated in zone 1 atmospheres and where zone 0 may
be present in tubes, the operator is to ensure that in the area of these tubes, no risk of
damage through the medium or mechanical assertion shall occur.
i) Seized screws or adhering joints (e.g. by frost or corrosion) are not to be opened with
force in the presence of a potentially explosive atmosphere.
j) Where substances of explosion group “A” or “IIC” are present and the presence of an
Ex-atmosphere is considered possible, only non-sparking tools shall be used.
h) The sensors loop hood may be produced from Aluminium alloy. In rare cases, ignition
sources due to impact and friction sparks could occur. This shall be considered during
installation particularly if the equipment is installed in a zone 0 location.
The danger of objects falling onto the sensor shall be excluded.
k) Combination of the external barriers from the transmitter has not been assessed.
Therefore, each input wiring circuit to the sensors should be kept segregated from the
other inputs as per requirements of the standards.
l) For the high temperature version, the temperature class, assigned maximum surface
temperature, maximum ambient temperature and Equipment Protection Level (EPL)
are dependent on the maximum process temperature applied by the end-user/installer.
The options are detailed under the description in the certificate. When the maximum
process temperature of the final installation is determined by the end user, the
temperature class, assigned maximum surface temperature, maximum ambient
temperature and the Equipment Protection Level (EPL) which are applicable to the
applied process temperature shall be observed and complied with.
The equipment is marked with the maximum ambient temperature and maximum
process temperature with all options stated in the certificate, but the limits may be
lower than those marked depending on the actual process temperature applied.
4.4 Requirements for installation dust environments
a) It is to be ensured that the sensor complies with the requirements of the degree of
protection of at least IP54 (cable glands and conduits) and gaskets must be protected
against adverse environmental conditions.
b) In certain extreme circumstances, the non-metallic parts incorporated in the enclosure
of the sensor may generate an ignition-capable level of electrostatic charge.
Therefore, the user/installer shall implement precautions to prevent the build-up of
electrostatic charge, e.g. locate the equipment where a charge-generating mechanism
(such as wind-blown dust) is unlikely to be present. Clean regularly with a damp cloth.
c) The sensors are to be electro-statically earthed. Electrostatic charging must be
avoided.
4.5 Ex relevant screw and bolt torques
There are no relevant torques to be observed.

Page 14 of 21
OPERATING MANUAL FOR
HPC EXPLOSION-PROOF FLOW METERS
5 Maintenance and repair work
5.1 Definition of terms according to IEC 60079-17:
Maintenance: defines a combination of any actions carried out to retain an item in, or restore
it to, conditions in which it is able to meet the requirements of the relevant specification and
perform its required functions.
Inspection: defines any action comprising careful scrutiny of an item carried out either without
dismantling, or with the addition of partial dismantling as required, supplemented by means
such as measurement, in order to arrive at reliable conclusion as to the condition of an item.
Visual inspection: defines an inspection which identifies, without the use of access
equipment and tools, those defects, such as missing bolts, which will be apparent to the eye.
Close inspection: defines an inspection which encompasses those aspects covered by a
visual inspection and, in addition, identifies those defects, such as loose bolts, which will be
apparent only be the use of access equipment, for example steps, where necessary, and
tools.
Detailed inspection: defines an inspection which encompasses those aspects covered by a
close inspection and, in addition, identifies those defects, such as loose terminations, which
will only be apparent by opening the enclosure, and/or using, where necessary, tools and test
equipment.
a) Maintenance or replacement work must be performed by qualified personnel only, i.e.
personnel qualified according to TRBS 1203 or similar.
b) Only auxiliary components which comply with all ATEX or/and IECEx requirements
national directives and legislations may be used in potentially explosive atmospheres
c) At the presence of Ex-atmospheres, the equipment must be regularly cleaned. The
intervals are to be defined by the operator in compliance with the environmental rules
valid at the place of operation.
d) After maintenance and repair works have been performed, all barriers and notices
removed for that purpose must be returned to their original place.
e) In the event that faults of the equipment are detected, the equipment is to be removed.
The internal components cannot be maintained by the customer. The equipment is to
be returned to the manufacturer for inspection.
f) Fuses, with the exception of the replaceable mains fuse, shall not be replaced by the
operator, since affected Zener-diodes must also be simultaneously replaced. This work
requires a follow-up adjustment and assessment, which can only be carried out at the
manufacturer’s factory.

OPERATING MANUAL FOR
HPC EXPLOSION-PROOF FLOW METERS
Page 15 of 21
Recommended inspection intervals
Activity
Visual inspection
Close inspection
Detailed
inspection
3-month interval
6-month interval
12-month interval
1
Visual inspection of
equipment for intactness,
removal of dust settlements
X
If necessary, at
shorter intervals
2
Check of electrical system
for intactness and
functionality
X
X
3
Check of entire system
User's responsibility
5.2 Fault elimination
No repairs or modifications may be performed on equipment that is operated in conjunction
with explosive atmospheres. Such equipment shall only be repaired by expert personnel
trained and authorized to do so.
Damaged threaded or flat joints which may impair the IP protection of the enclosure shall not
be repaired or modified. The equipment shall be returned to the manufacturer for repair and
replacement.
5.3 Disposal
Packaging material and worn components shall be disposed of according to the regulations
applicable in the country of installation.

Page 16 of 21
OPERATING MANUAL FOR
HPC EXPLOSION-PROOF FLOW METERS
6 Model Code
The following table depicts the model-code of the HPC sensor. The Ex relevant positions of
the model code are marked yellow:
HPC-
A
B
C
-
D
E
F
G
-
H
I
J
K
-
L
M
-
N
O
-
P
-
Q
Pos.
Marking
Remarks
A
Wetted Material
Non-Ex relevant position
B,C
Model size
Non-Ex relevant position
D,E,F,G
Process Connection
Non-Ex relevant position
H,I
Pressure rating
Non-Ex relevant position
J
Enclosure options
Non-Ex relevant position
K
Type of installation
Non-Ex relevant position
L
Sensor configurations
R - Remote -40°C to 80°C (-40°F to 176°F)
L - Remote -40°C to 180°C (-40°F to 356°F)
X - Customer specified
with HAN R23 Connector
M
Approvals
L - ATEX / IECEx
(in combiantion with „R“ from Pos. „L“)
Or
L - ATEX / IECEx
(in combiantion with „L“ from Pos. „L“)
II 1G Ex ia IIC T4 Ga
II 1DEx ia IIIC T135°C Da
or
II 1G Ex ia IIC T4 Ga
II 1DEx ia IIIC T135°C Da
II 2D Ex ia IIIC T195°C/240°C Db
N
Calibration Flow
Non-Ex relevant position
O
Calibration Density
Non-Ex relevant position
P
Supplementary Equipment
Non-Ex relevant position
Q
Design
Non-Ex relevant position

OPERATING MANUAL FOR
HPC EXPLOSION-PROOF FLOW METERS
Page 17 of 21
7 Relevant Standards for Hazardous Locations
7.1 ATEX
•DIN EN 60079-0:2012 + A11:2013
Explosive atmospheres –Part 0: General Requirements
•DIN EN 60079-11:2012
Explosive atmospheres –Part 11: Equipment protection by intrinsic safety “i”
7.2 IECEx
•IEC EN 60079-0:2011 Edition 6, modified Cor. 2012 + Cor. 2013
Explosive atmospheres –Part 0: General Requirements
•IEC 60079-11:2011 Edition 6 + Cor. 2012
Explosive atmospheres –Part 11: Equipment protection by intrinsic safety “i”

Page 18 of 21
OPERATING MANUAL FOR
HPC EXPLOSION-PROOF FLOW METERS
8 Declaration of Conformity
EU-Konformitätserklärung
EU-Declaration of Conformity
19.4142.02
Hersteller:
Manufacturer:
Heinrichs Messtechnik GmbH
Robert-Perthel-Strasse 9
50739 Köln
Produktbeschreibung:
Product description:
Coriolis Durchflussmessgerät UMC4 für Verwendung mit
den Sensorreihen TM* und HPC
Coriolis Flowmeter UMC4 for use with the Sensor series
TM* and HPC
Hiermit erklären wir, in alleiniger Verantwortung, dass das oben genannte Messsystem den
Anforderungen der folgenden EU-Richtlinien, einschließlich allen bis heute veröffentlichten Änderungen
bzw. Nachträgen entspricht:
We declare herewith, in sole responsibility, that the product described above is conform with the
provisions of the following EU-directives, including all published changes and amendments as of today:
2014/30/EU (EMC)
EU-Richtlinie über die Elektromagnetische Verträglichkeit
EU-Directive relating to electromagnetic compatibility
2014/34/EU (ATEX)
EU-Richtlinie über Geräte zur Bestimmungsgemäßen Verwendung in
explosionsgefährdeten Bereichen.
EU-Directive relating to electrical equipment intended for use in potentially
explosive atmospheres
2014/35/EU (LVD)
EU-Richtlinie über die Bereitstellung elektrischer Betriebsmittel zur
Verwendung innerhalb bestimmter Spannungsgrenzen auf dem Markt
EU-Directive relating to the making available on the market of electrical
equipment designed for use within certain voltage limits
2014/68/EU (PED)
EU-Richtlinie zur Harmonisierung der Rechtsvorschriften der Mitgliedstaaten
über die Bereitstellung von Druckgeräten auf dem Markt
EU-Directive on the harmonisation of the laws of the Member States relating
to the making available on the market of pressure equipment
Anhang N und X sind ein integraler Bestandteil dieser Erklärung
Annex N and X are an integral part of this declaration
Köln, den 09.12.2019
Frank Schramm
(Geschäftsführung / Managing Director)
Kontakt: Tel: [phone]
Contact: Email: [email protected]
Web: www.heinrichs.eu

OPERATING MANUAL FOR
HPC EXPLOSION-PROOF FLOW METERS
Page 19 of 21
Anhang N zur EU-Konformitätserklärung
Annex N of the EU-Declaration of Conformity
No. 19.4142.02
Produktbeschreibung:
Product description:
Coriolis Durchflussmessgerät UMC4 für Verwendung mit
den Sensorreihen TM* und HPC
Coriolis Flowmeter UMC4 for use with the Sensor series
TM* and HPC
Die Konformität mit den auf Seite 1 genannten Richtlinien diese Erklärung wird nachgewiesen durch die
Einhaltung folgenden Normen (abhängig von Gerätvariant):
Conformity to the Directives referred to on Page 1 of this Declaration is assured through the application
of the following standards (depending on version of device):
X: Zutreffende Norm / Applicable Standard
Name und Anschrift der Notifizierte Stelle / Name and Address of the Notified Body
TÜV-SÜD Industrie Service GmbH
TÜV SÜD Gruppe
Westendstrasse 199
D-80686 München
ID-Nr. / ID-No.: RL 2014/68/EU: 0036
DEKRA EXAM GmbH
Carl-Beyling-Haus
Dinnendahlstrasse 9
D-44809 Bochun
ID-Nr. / ID-No.: RL 2014/34/EU: 0158
Richtlinie
Direktive
Norm –Ref.
Nr.
Standard /
Ref. No.
DIN EN -
Ausgabe
Edition
Norm Beschreibung
Standard Description
UMC4
TM/ TMU/ TME/ TMR
TM-SH
HPC
2014/30/EU
61000-6-2
2011-06
Immunity Industrial enviroment
X
61000-6-3
2012-11
Emission residential enviroment
X
55011
2011-04
Radio frequency disturbance
X
61326-1
2011-07
EMC requirements
X
2014/34/EU
60079-0
2012+
A11:2013
General requirements
X
X
X
X
60079-1
2014
Flameproof Enclose „d“
X
60079-11
2012
Intrinsic Safety „i“
X
X
X
X
60079-26
2015
Protection Level (EPL) „Ga“
X
X
X
2014/35/EU
61010
2011-07
Safety requirements
X
X
X
2014/68/EU
AD 2000-Merkblätter
Module H
X
X

Page 20 of 21
OPERATING MANUAL FOR
HPC EXPLOSION-PROOF FLOW METERS
Anhang X zur EU-Konformitätserklärung
Annex X of the EU-Declaration of Conformity
No. 19.4142.02
Produktbeschreibung:
Product description:
Coriolis Durchflussmessgerät UMC4 für Verwendung mit
den Sensorreihe TM*
Coriolis Flowmeter UMC4 for use with the Sensor series
TM*
Gerät Zulassungen / Device certification
EG-Baumusterprüfbescheinigung
EC-type examination certificate
Nachtrag
Supplement
Kennzeichnung
Marking
Für kompletten
Kennzeichnung, siehe
Betriebsanleitung
UMC4
TM/TMU/ TME/TMR
TM-SH
HPC
BVS 10 ATEX E 110 X
1
II (1) 2G
X
DMT 01 ATEX E 149 X
7
II 1/2G
X
X
CML 19 ATEX 2096 X
0
II 1G II 1/2D
X
X: Zutreffende Norm / Applicable Standard
Die oben genannten Produkte entsprechen der Richtlinie 2014/34/EU. Neue Editionen können bereits
eine oder mehrere der in den jeweiligen EU-Baumusterprüfbescheinigungen genannten Normen ersetzt
haben.
Der Hersteller erklärt, dass alle Produkte erwähnt in dieser Konformitätserklärung auch der
Anforderungen der neuen Editionen einhalten, da die veränderten Anforderungen der neuen Editionen
haben entweder keinen Einfluss auf das Produkt, oder das Produkt die Anforderungen erfüllt.
The above-mentioned products comply with the Directive 2014/34/EU. New editions may have already
replaced one or more of the Standards stated in the respective EU-Type-examination certificates. The
manufacturer declares that all products mentioned in this Declaration of Conformity also comply with the
requirements of the new editions since the changed requirements of the new editions either do not affect
the product, or the product also fulfils the requirements.
Heinrichs Messtechnik GmbH
Robert-Perthel-Straße 9
50739 Köln
Telefon [phone]
Telefax 0221/49708-178
http://www.heinrichs.eu
[email protected]
Bankverbindung
Dresdner Bank Köln
BLZ 370 800 40
Konto-Nr. 0955 051300
IBAN :
DE58 3708 0040 0955 0513 00
SWIFT-BIC: DRES DE FF 370
Erfüllungsort und Gerichtsstand:
Köln
Amtsgericht Köln HRA 37040
Ust.IDNr.: DE813416533
Steuer-Nr.: 217/5743/0386
Geschäftsführer
Frank Schramm