Home Auto: KHV-444/454/446/456
- Do not insert any metallic materials into the insi e of fuse cover. It may cause electric shock.
- Do not close ear to speaker. Abrupt call or signal may give harmful effects on user's hearing.
- After turning power on an off, check again that input contents are save correctly. Otherwise, ata may be misse when auto-signal mo e operates.
- Use a stan ar etector. Non-stan ar ize etectors are likely to cause fire ue to excessive voltage or current.
- Please install motion etector at a place easily etect the motions of subjects. When etector is installe at a wrong place or obstacles block the front
si e of etector, it cannot work well.
- When setting night guar mo e, be sure that etector shoul be connecte well.
- Sufficiently charge the battery of wireless han set before using it. Be careful that chil ren shoul not throw battery. Be sure to close battery cover
(When chil ren throw or isassemble battery, it may cause serious acci ents).
- Be careful that the polarity of the pro uct matches to that of guar room communication cable. When polarity is reverse , it may cause abnormal
operations of the pro uct or apartment system as a whole.
4-Line Relate Pro ucts: KVM-930, 931, 960, IP-203APB, AM-10KP, KCV-344/354
- In wiring work, be careful that wirings shoul keep away from the wall-mounting pegs or other furniture at regular interval. Contact of wiring with
wall-mounting pegs, etc. may cause short-circuit, electric shock an fire (it is applie to all pro ucts with wall-mounting pegs).
- Use the prescribe stan ar wirings. Non-stan ar ize wirings may give a verse effects on operation of pro uct
(it is applie to both vi eo phone an CCTV).
CCTV Camera
- Do not install at noisy places.
- Do not install at the place expose to electromagnetic waves.
Excessive electromagnetic waves may cause continuous noise on screen an mechanical troubles.
- When installing camera out oor, please put it in the out oor case. Otherwise, when it rains, the camera may be broken or operate incorrectly.
- Install the pro uct at well-ventilate places.
- Do not use the pro uct for me ical or military uses.
- Do not install the pro uct at humi places. It may cause re uction of the pro uct's urability as well as fire an electric shock.
- When lens is staine with alien substances, clean it with soft cloth to prevent the amages on it.
- Install the pro uct out of reach of chil ren.
System for Multi-unit Housing
- In installation, be careful that other wiring or metallic substances shoul not contact to the system for multi-unit housing.
- In installation, be careful that alien substances shoul not go into the system.
- Before installation, be fully aware of wiring specifications of each mo el.
- In installation, be sure that the length an imension of wiring meet the requirement prescribe in installation manual.
- Excessive strength an external shock may cause mechanical break owns of equipment.
- Do not arbitrarily open the case of the pro uct
(When user opens the case arbitrarily, KOCOM may reject to provi e A/S service).
Lobby Phone: KLP-(100, 104, 108, 112), KLP-(P100, P104, P108, P112), KDP-(100, 104, 108,112)
- A stroke of lighting or strong shock may give fatal an a verse effects on system. Thus, o not fail to groun the system.
- For registration of househol passwor , please refer to user manual of the concerne pro uct (it is applie to ten-key lobby phone pro ucts
[KLP-100, KLP-P100 an KDP-100]).
Image Splitter: KSV-104P
- An image splitter can support up to four househol s.
- In the case of over four househol ers, a itional image splitters are nee e .
Image Amplifier: KHU-102P
- In installation, follow the specification for image in/output.
Vi eo Phone
- In assembling the pro uct, be careful that wall-mounting pegs shoul not contact with wirings.
- In connection of cables, strip its insulation off as much as necessary (Excessive stripping off its insulation may cause short circuit).
- Be careful that signal cables shoul not be wire with A/C wiring (it may cause poor isplay quality).
- Do not rop han set (its amage or short-circuit ue to rop may make communication impossible).
- When connecting wires to terminals, use stan ar screw river (otherwise, screws may loosen, which will result in isconnection of wiring).
- Do not clean CRT screen with wet towel or cloth. When water penetrates into the pro uct, it may cause short-circuit.
Do not fail to clean it with ry towel or soft cloth.
- Do not install camera at the place where water penetrates or leaks. Penetration or leakage of water may cause electric shock or short circuit.
Safety Instructions, Warnings, an Cautions of Each System
- This equipment is electronically precision equipment, so o not arbitrarily isassemble it.
- In installation of the pro uct, o not fail to follow the specifications (specifications offere by KOCOM).
- Do not touch the pro uct with alien materials (for example, sticker, magnet, opener, metal chopstick, etc.)
or insert them into the pro uct (it may cause re uction of the pro uct's urability an harmful results to user as well).
- In the rainy season, water is likely to penetrate into the pro uct along the wiring. Thus, U-type finishing is recommen e
as a esirable metho of en part finishing.
