Kodak DryView 8150 User guide

SAFETY MANUAL
See Pages 1-3 through 1-4 and 1-9 through 1-10
for compliance statements and modification warnings.

Kodak DryView
8150 Laser Imager
Safety Manual

Eastman Kodak Company
343 State Street
Rochester, NY 14650
© Eastman Kodak Company, 2004
Kodak and DryView are trademarks.
7F3779
Catalog number 1415014
Rev. A

September 27, 2004 i
Table of Contents
1 Safety and Related Information
Safety, Warnings, and Cautions........................................................................................................................1-1
Safety Labels.............................................................................................................................................1-5
Safety and Health Compliance..........................................................................................................................1-8
Safety........................................................................................................................................................1-8
EMC..........................................................................................................................................................1-9
EU Directives..........................................................................................................................................1-16
CE Marking.............................................................................................................................................1-17
Note........................................................................................................................................................1-18

ii September 27, 2004
Table of Contents

September 27, 2004 7F3779 1-1
1 Safety and Related
Information
Safety, Warnings, and Cautions
Please read and understand all instructions before using the Kodak
DryView 8150 Laser Imager.
RISK OF ELECTRIC SHOCK:
This equipment is operated with hazardous voltage which can shock,
burn or cause death.
• Remove wall plug before servicing equipment. Never pull on cord to
remove from outlet. Grasp plug and pull to disconnect. Only an
Authorized Service Provider of Kodak productsmay perform
service maintenance on this equipment.
• Do not operate equipment with a damaged power cord.
• Do not use an extension cord to power this equipment.
• Do not operate equipment with any of the safety interlocks overridden.
• Position the power cord so it will not be tripped over or pulled.
• Connect this equipment to a grounded wall outlet.
• Do not operate equipment with the covers open.
WARNING:
This equipment contains moving parts that may be
accessible to the user. Loose clothing, jewelry or long hair
may cause personal injury or damage to the equipment.

1-2 7F3779 September 27, 2004
Safety and Related Information
WARNING:
This equipment is not contained in a sealed cabinet. Do
not use this equipment in locations where it can come in
contact with liquids, including body fluids.
CAUTION:
This equipment is intended to connect to other medical
devices. Only an Authorized Service Provider of Kodak
products or Customer’s Qualified Service Personnel may
install this equipment.
CAUTION:
Only an Authorized Service Provider of Kodak products may
perform service maintenance on this equipment.
CAUTION:
Do not use a cell phone within 2 meters (6.56 feet) of this
equipment even if you are separated by a wall from this
equipment.
CAUTION:
Do not use a microwave oven within 4 meters (13.12 feet) of
this equipment. Electromagnetic radiation from a microwave
oven is only an issue if after the oven door is closed and
latched, the seal does not maintain an electromagnetic tight
fit between the oven door and oven main housing.
Determining if the seal has an electromagnetic tight fit
requires special detection equipment.
CAUTION:
Do not use in the presence of flammable anesthetics, oxygen,
or nitrous oxide. This equipment does not have a gas-sealed
electronics enclosure and could ignite any flammable or
explosive gases present in its environment.

Safety and Related Information
September 27, 2004 7F3779 1-3
CAUTION:
This equipment should not be located within the patient
environment. Therefore, do NOT locate this equipment
closer than 1.83 meters (6 feet) from a patient bed or chair.
CAUTION:
This equipment should not be used in close contact with MRI
devices, due to possible very high magnetic fields near an
MRI unit. The magnetic field in the area where this
equipment is installed must be less than 50 Gauss.
CAUTION:
Do not substitute or modify any part of this equipment
without prior written approval of Eastman Kodak Company.
CAUTION:
(USA Only)
Federal law prohibits dispensing without a prescription.
CAUTION:
FCC (USA Only)
This equipment has been tested and found to comply with
the limits for a class A digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the
1.83 m

1-4 7F3779 September 27, 2004
Safety and Related Information
instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a
residential area is likely to cause harmful interference in
which case the user will be required to correct the
interference at his own expense.
CAUTION:
Do not use isopropyl alcohol to clean the exterior surfaces
of this equipment because alcohol can dissolve the exterior
paint on the equipment.
CAUTION:
Filters are considered to be non-hazardous waste according
to the US Environmental Protection Agency Resource
Conservation Recovery Act (RCRA). You may dispose of
filters in a landfill or incinerator with energy recovery in a
municipal, commercial or industrial facility. Contact your
state or local government to determine if additional disposal
requirements apply.
CAUTION:
This equipment contains lead and mercury. The lead is
located in the solder on the circuit boards. Mercury is
located in the back light of the local panel. Disposal of
components containing these materials may be regulated
due to environmental considerations. For disposal or
recycling information at the end of usable service, please
contact your local authorities or visit the Electronics
Industry Alliance Web site at: http://www.eiae.org.
LASER WARNING:
The equipment uses a 50-milliwatt invisible laser. Laser
radiation may be present behind this back panel. The back
panel may only be removed by an Authorized Service
Provider of Kodak products or Customer’s Qualified
Service Personnel. EXPOSURE TO LASER ENERGY MAY
RESULT IN EYE DAMAGE.

Safety and Related Information
September 27, 2004 7F3779 1-5
Safety Labels Safety labels are attached to this equipment in compliance with
international standards.
Processor Drum Cover Labels
8150
8150001
7F1000
6551261
January 2004
100/120/230V
12/10/7 A
50/60Hz
12
3
1Processor Drum Cover label - Warns operators to avoid hot
surfaces when the processor drum cover is open.
2Caution Hot Surface label - Warns operators to use care near the
processor drum to avoid possible burns.
3Serial Plate label - Shows the serial number and model number of
this equipment along with several other important data items.

1-6 7F3779 September 27, 2004
Safety and Related Information
Rear Panel - Warning and Caution Labels
1
2
3
4
5
6
1Invisible Laser Radiation Present When Open label - Warns
operators that invisible laser radiation is present under the panel
where the label is attached. Only an Authorized Service Provider of
Kodak products or Customer’s Qualified Service Personnel should
attempt access.
2Hazardous Voltage label - Warns operators that high voltage is
present under panels where the label is attached. Only the an
Authorized Service Provider of Kodak products or Customer’s
Qualified Service Personnel should attempt access.

Safety and Related Information
September 27, 2004 7F3779 1-7
3Static Sensitive Equipment label - Identifies static-sensitive
components. Connect a personal grounding strap to appropriate
ground before servicing this equipment. Only an Authorized
Service Provider of Kodak products may perform service
maintenance on this equipment.
4Class1 LaserProduct -Indicatesthatthisequipment complieswith
IEC requirements for a Class 1 Laser Product.
5RadioFrequencyEnergy-Indicatesthatthisequipmentcanradiate
radio frequency energy. If not installed and used in accordance
with the instructions, this equipment may cause harmful
interference to radio communications.
6Japanese Import License - Not safety-related.

1-8 7F3779 September 27, 2004
Safety and Related Information
Safety and Health Compliance
This equipment has been tested for and complies with the following Safety
and Emissions Standards. Certificates of Compliance and Declarations of
Conformity have been issued as shown below.
Safety United States
Canada
Europe
21 CFR 1040.10 Class I: FDA CDRH Code of Federal Regulations Title 21
Food and Drugs, Volume 8 - Food and Drugs, Part 1040 - Performance
Standards for Light Emitting Products, Section 10 - Laser Products.
FDA95-415PremarketNotification 510(K): RegulatoryRequirementsFor
Medical Devices.
UL 60950-1: Safety of Information Technology Equipment. (3rd Edition)
UL 60601-1-1: Medical electrical equipment - Part 1: General
requirements for safety - Section 1: Collateral standard: Safety
requirements for medical electrical systems, Clause 19.
IEC 60825-1: Safety of laser products - Part 1: Equipment classification,
requirements and user’s guide.
C22.2NO60950-1CAN/CSA,SafetyofInformationTechnologyEquipment,
Including Electrical Business Equipment (Gen Instr 1) (UL 1950-95).
IEC 60825-1: Safety of Laser products - Part 1: Equipment classification,
requirements and user’s guide.
EN60950-1: Safety of Information Technology Equipment, Including
Electrical Business Equipment (2000).
EN60601-1-1: Medical electrical equipment - Part 1: General
requirements for safety - Section 1: Collateral standard: Safety
requirements for medical electrical systems, Clause 19.
EN60825-1: Safety of laser products - Part 1: Equipment classification,
requirements and user's guide.

Safety and Related Information
September 27, 2004 7F3779 1-9
Rest of World
EMC United States
Canada
IEC 60950-1: Safety of information technology equipment.
IEC 60601-1-1: Medical electrical equipment - Part 1: General
requirements for safety - Section 1: Collateral standard: Safety
requirements for medical electrical systems, Clause 19.
IEC 60825-1: Safety of laser products - Part 1: Equipment classification,
requirements and user's guide.
FCC Rules and Regulations, Title 47, Part 15, Subpart B, Class A: Radio
Frequency Devices: Unintentional Radiators.
This equipment has been tested and been found to comply with the limits
foraClassAdigitaldevicepursuanttopart15oftheFCCrules.Thoselimits
are designed to provide reasonable protection against harmful
interference in a commercial environment. This equipment generates,
uses,and can radiateradio frequency energyand, ifnotinstalledandused
in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
FCC Rules and Regulations, Title 47, Part 15, Subpart C, Radio Frequency
Devices: Intentional Radiators. “FCC ID: PA481507E2537"
CAN/CSA-C108.6-M91, Class A: Limits and Methods of Measurement of
Electromagnetic Disturbance Characteristics of Industrial, Scientific and
Medical (ISM) Radio-Frequency Equipment. (CISPR 11,Class A
(EN55011)).
RSS-210, Issue 5:2001, Section 6.2.2(e): Low Power License-exempt
Radio Communication Devices (All Frequency Bands), a Spectrum
Management and Telecommunications Policy, Radio Standard
Specification.
Intentional Radiation “IC: 1016B-8150”

1-10 7F3779 September 27, 2004
Safety and Related Information
Europe
Rest of World
Japan
This Class A digital apparatus complies with Canadian ICES-003.
CET APPAREIL NUM ENRIQUE DE CLASSE A EST CONFORME A LA NORME
NMB–003 DU CANADA.
This Class A digital apparatus meets all requirements of the Canadian
Interference-Causing Equipment Regulations.
European Telecommunication Standard (ETS) EN300 330:
Electromagnetic Compatibility and Radio Spectrum Matters (ERM); Short
Range Devices (SRD); Technical Characteristics and Test Methods for
Radio Equipment in the Frequency Range 9 kHz to 25 MHz and Inductive
loop Systems in the Frequency Range 9 kHz to 30 MHz.
European Telecommunication Standard (ETS) EN300 489-3:
Electromagnetic Compatibility and Radio Spectrum Matters (ERM) -
Electromagnetic compatibility (EMC) standard for radio equipment and
services - Part 3: specific conditions for short-range devices (SRD)
operating on frequencies between 9 kHz and 40 GHz.
IEC 60601-1-2: Medical electrical equipment - Part 1-2: General
requirements for safety - Collateral standard: Electrical compatibility -
Requirements and tests.
VCCI V.3/2001.04: Agreement of Voluntary Control Council for
Interference by Information Technology Equipment Technical
Requirements.

Safety and Related Information
September 27, 2004 7F3779 1-11
Europe and the Rest of the World
Guidance and Manufacturer’s Declaration for Electromagnetic Emissions
The Kodak DryView 8150 Laser Imager is intended for use in the electromagnetic environment specified below. The
customer or user of the Kodak DryView 8150 Laser Imager should assure that it is used in such an environment.
Emissions Test Compliance Electromagnetic Environment - Guidance
RF emissions:
• EN55011
•CISPR11
Group 1 The Kodak DryView 8150 Laser Imager uses RF energy only for its
internal function.Therefore,its RFemissions areverylowandare not
likely to cause any interference in nearby electronic equipment.
RF emissions:
• EN55011
•CISPR11
Class A The Kodak DryView 8150 Laser Imager is suitable for use in all
establishments other than domestic and those directly connected to
the public low-voltage power supply network that supplies buildings
used for domestic purposes.
Harmonics emissions:
• EN61000-3-2
• IEC 61000-3-2
Class A The Kodak DryView 8150 Laser Imager is suitable for use
everywhere, including those establishments directly connected to the
publiclow-voltagepowersupplynetworkthatsuppliesbuildings used
for domestic purposes.
Voltage fluctuations and
flicker emissions:
• EN61000-3-3
• IEC 61000-3-3
Complies The Kodak DryView 8150 Laser Imager is suitable for use
everywhere, including those establishments directly connected to the
publiclow-voltagepowersupplynetworkthatsuppliesbuildings used
for domestic purposes.

1-12 7F3779 September 27, 2004
Safety and Related Information
Guidance and Manufacturer’s Declaration for Electromagnetic Immunity
The Kodak DryView 8150 Laser Imager is intended for use in the electromagnetic environment specified below. The
customer or user of the Kodak DryView 8150 Laser Imager should assure that it is used in such an environment.
Immunity Test IEC 60601 Test Level Compliance Level Electromagnetic Environment -
Guidance
Electrostatic
discharge (ESD):
• EN61000-4-2
• IEC 61000-4-2
± 6 kV contact
±8 kV air ± 6 kV contact ± 8 kV air
Floors should be wood, concrete, or
ceramic tile. If floors are covered with
synthetic material, the relative humidity
should be at least 30%.
Electrical fast
transient/burst:
• EN61000-4-4
• IEC 61000-4-4
± 2 kV forpowersupply
lines
± 1 kV for input/output
lines
± 2 kV for power supply
lines
± 1 kV for input/output
lines
Mains power quality should be that of a
typical commercial or hospital
environment.
Surge:
• EN61000-4-5
• IEC 61000-4-5
± 1 kV differential mode
± 2 kV common mode ± 1 kV differential mode ± 2 kV common mode
Mains power quality should be that of a
typical commercial or hospital
environment.
Voltage dips, short
interruptions and
voltage variations
on power supply
lines:
• EN61000-4-11
• IEC 61000-4-11
<5% Uτ* (>95% dip in
Uτ*) for 0.5 cycle
40% Uτ* (60% dip in
Uτ*) for 5 cycles
70% Uτ* (30% dip in
Uτ*) for 25 cycles
<5% Uτ* (>95% dip in
Uτ*) for 5 sec.
<5% Uτ* (>95% dip in
Uτ*) for 0.5 cycle
40% Uτ* (60% dip in
Uτ*) for 5 cycles
70% Uτ* (30% dip in
Uτ*) for 25 cycles
<5% Uτ* (>95% dip in
Uτ*) for 5 sec.
Mains power quality should be that of a
typical commercial or hospital
environment. If the user of the Kodak
DryView 8150 Laser Imager requires
continued operation during power
mainsinterruptions,itisrecommended
that the Kodak DryView 8150 Laser
Imager be powered from an
uninterruptible power supply or a
battery.
NOTE: * Uτis the a.c. mains voltage prior to application of the test level.
Power frequency
(50/60 Hz)
magnetic field:
• EN61000-4-8
• IEC 61000-4-8
3 A/m 3 A/m Mains power quality should be that of a
typical commercial or hospital
environment.

Safety and Related Information
September 27, 2004 7F3779 1-13
Guidance and Manufacturer’s Declaration for Electromagnetic Immunity
The Kodak DryView 8150 Laser Imager is intended for use in the electromagnetic environment specified below. The
customer or user of the Kodak DryView 8150 Laser Imager should assure that it is used in such an environment.
Immunity
Test IEC 60601 Test Level Compliance Level Electromagnetic Environment - Guidance
PortableandmobileRF communications equipmentshouldbe
used no closer to any part of the Kodak DryView 8150 Laser
Imager, including cables, than the recommended separation
distance calculated from the equation applicable to the
frequency of the transmitter.
Recommended Separation Distance:
Conducted RF
IEC 61000-4-6
3 Vrms
150kHzto 80MHz 3 Vrms
Radiated RF
IEC 61000-4-3
3 v/m
80 MHz to 2.5 GHz 3 v/m 80 MHz to 800 MHz
800 MHz to 2.5 GHz
dis the recommended separation distance in meters (m).
Pis the maximum output rating ofthe transmitter in watts (W)
according to the transmitter manufacturer.
Fieldstrengths fromfixedRF transmitters,as determinedby an
electromagnetic site survey a, should be less than the
compliance level in each frequency range b.
Interference may occur in the vicinity of equipment marked
with the following symbol:
NOTE:
• At 80 MHz and 800 MHz, the higher frequency range applies.
• These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and
reflection from structures, objects and people.
aSee Note 1 on next page.
b See Note 2 on next page.
d1.17 P=
d1.17 P=
d2.33 P=

1-14 7F3779 September 27, 2004
Safety and Related Information
Note 1 Field strengths from fixed transmitters, such as base station for radio (cellular/cordless) telephones
and land mobile radios, amateur radio, AM and FM radio broadcast and TV broadcast cannot be
predicted theoretically with accuracy. To assess the electromagnetic environment due to fixed RF
transmitters, an electromagnetic site survey should be considered. If the measured field strength in
the location in which the Kodak DryView 8150 Laser Imager is used exceeds the applicable RF
compliance level on the previous page, the Kodak DryView 8150 Laser Imager should be observed
to verify normal operation. If abnormal performance is observed, additional measures may be
necessary, such as reorienting or relocating the Kodak DryView 8150 Laser Imager.
Note 2 Over the frequency range 150 kHz to 80 MHz, field strengths should be less than 3 v/m.
Guidance and Manufacturer’s Declaration for Electromagnetic Immunity

Safety and Related Information
September 27, 2004 7F3779 1-15
Recommended separation distance between portable and mobile RF communications
equipment and the Kodak DryView Model 8150 Laser Imager
The Kodak DryView 8150 Laser Imager is intended for use in an electromagnetic environment in which radiated RF
disturbances are controlled. The customer or the user of the Kodak DryView 8150 Laser Imager can help prevent
electromagnetic interference by maintaining a minimum distance between portable and mobile RF communication
equipment (transmitters) and the Kodak DryView 8150 Laser Imager as recommended below, according to the
maximum output of the communications equipment.
Rated maximum output
power of transmitter (P)
in Watts (W)
Separation distance (d) according to frequency of transmitter
in meters (m)
150 kHz to 80 MHz 80 MHz to 800 MHz 800 MHz to 2.5 GHz
0.01
0.1
1
10
100
For transmitters rated at a maximum output power not listed above, therecommended separation distance din meters
(m)canbeestimatedusingtheequationapplicabletothefrequencyofthe transmitter,whereP isthemaximumoutput
power rating of the transmitter in watts (W) according to the transmitter manufacturer.
NOTE 1: At 80 MHz and 800 MHz, the separation distance for the higher frequency range applies.
NOTE 2: These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and
reflection from structures, objects and people.
d1.17 P=d1.17 P=d2.33 P=