Kodak ishow 1000 User manual

User Manual

1
CONTENTS
CONTENTS........................................................ 1
BEFORE YOU START........................................ 3
FCC Warning ...........................................................................3
For Customers in Europe.........................................................4
About this Manual ....................................................................5
SAFETY PRECAUTIONS................................... 6
GETTING READY .............................................. 7
Accessories Included...............................................................7
Part Names..............................................................................8
Charging Battery......................................................................9
Downloading and installing iShow (wireless projector) app.. 10
Basic Operations of the Projector ....................11
Turning on the projector........................................................ 11
Setting up the projector using the support ............................ 11
Adjusting focus ..................................................................... 12

2
Turning off the projector........................................................ 12
Resetting the projector.......................................................... 12
Setup iShow (wireless projector) app for
projection .........................................................13
For iOS system ..................................................................... 13
For Android system............................................................... 14
For Windows system ............................................................ 16
Set the application (available only in wireless
connection).......................................................18
SSID ..................................................................................... 18
Hibernation / Sleep Mode ..................................................... 18
Keystone Correction ............................................................. 19
About .................................................................................... 19
Using HDMI for projection ................................20
Firmware Update..............................................21
Specications ...................................................22

3
FCC Warning
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one
or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this
device must accept any interference received, including interference
that may cause undesired operation.
Changes or modications not expressly approved by the party
responsible for compliance could void the user's authority to operate
the equipment.
BEFORE YOU START
1

4
For Customers in Europe
This symbol [crossed-out wheel bin WEEE Annex IV] indicates
separate collection of electrical waste and electronic equipment in
the European countries. Please do not throw the equipment into
domestic refuse. Please use the return and collection systems
available in your country for proper, safe disposal of this product.
“CE” mark indicates that this product complies with the European
requirements for safety, health, environment, and customer
protection. “CE” marked products are intended for sales in Europe.
Europe – EC Declaration of Conformity
This device complies with the essential requirements of the R&TTE
Directive 1999/5/EC.
Copy of the EC declaration can be obtained from JK Europe Ltd.
Packing: Please follow local regulations for the recycling of
packaging.
Batteries: Please dispose of used batteries at designated collection
centers.

5
About this Manual
Thank you for purchasing this KODAK iShow 1000 Pico Projector. Please
read this manual carefully and keep it in a safe place for future reference.
Windows is registered in the United States and other countries by
Microsoft Corporation, and its trademark use rights are reserved by
Microsoft Corporation.
Product names and trademarks involved in the Manual are for illustrative
and identication purposes only. All of them are the registered trademarks
or copyrights of their original companies.
This manual provides you with instructions on how to use your new
KODAK iShow 1000 Pico Projector. Every effort has been made to
ensure that the contents of this manual are accurate; however JK
Imaging Ltd. reserves the right to make changes without notice.

6
When using a pico projector, please note the following safety precautions to
prevent damage to the product.
Do not dispose of improperly or expose to extreme heat.
Do not operate the pico projector in moist or wet environments. Exposure
to water may cause electrical shock or other injury.
Avoid exposure to extreme temperatures as this may damage the
pico projector.
Do not operate the pico projector if damaged. Disassembling the pico
projector will void the warranty.
Do not point the pico projector directly into your eyes or those of anyone
else while in use.
Do not place or store the pico projector on a wet surface or in places
where dripping water or sand may come in contact with the
pico projector; doing so may cause irreparable damage.
Keep the pico projector out of reach of babies, small children and
animals.
Avoid placing pico projector on a vibrating or an unstable surface.
If the projector lens is dirty, use a soft cleaning cloth to clean the lens.
Do not use pico projector in the following types of locations.
1. In rain, very humid or dusty environments.
2. In a place where pico projector can be exposed directly to sunlight or
subject to high temperatures, e.g. inside a closed car in summer.
3. In a place where the pico projector is subject to a high magnetic eld,
e.g. near motors, transformers or magnets.
2SAFETY PRECAUTIONS

7
3GETTING READY
Accessories Included
Your KODAK iShow 1000 Pico Projector box should contain the pico projector
you purchased along with the following accessories. If anything is missing or
appears to be damaged, please contact your retailer.
AC Adapter
Warranty Card
STOP
Service Card
CD-ROMQuick Start Guide
Quick Start Guide

8
Part Names
Focus slider
Earphone jack
Power inlet
Reset hole
Power button
HDMI port
Tripod receptacle
Support
Lens
Status indicator
Speaker

9
Charging Battery
1. Ensure the projector is turned off and connect it to the power charger.
2. Insert the plug of the power charger into the wall outlet to charge the
battery.
3. Charging indicator:
Red: Charging
Green: Charging complete
4. To have maximum battery life, charge the battery for at least 4 hours the
rst time.

10
Downloading and installing iShow (wireless projector) app
1. For iOS system users: Please search for the iShow (wireless projector)
app in the App Store ®, download the app, and install it on your
device.
2. For Android system users: Please search for the iShow (wireless
projector) app in Google Play ®, download the app, and install it on
your device.
3. For Windows 8/7 system users: Please use the installing software item
on the CD-ROM (included) to conduct the installation of the iShow
(wireless projector) app.

11
4
Turning on the projector
1. Press and hold the power button for three seconds to power up the
projector. The button can be released when the status indicator lights up.
2. The projector will display the start up screen.
Pico Projector
Setting up the projector using the support
1. Open the support.
2. Place the projector on a stable surface.
Basic Operations of the Projector

12
Adjusting focus
1. Move the focus slider to adjust the clarity of the
projected image.
2. Stop moving the slider once the projected image
becomes clear.
Turning off the projector
1. Before turning off the projector, close any les that are being displayed.
2. Press and hold the power button for three seconds to turn off the
projector.
Resetting the projector
In case the projector acts erratically and/or the system crashes, please press
the reset hole (located on the bottom of the projector) with a ne-like object (a
paper-clip) to reset the projector. The projector will shut down and restart to
the normal state.

13
5
For iOS system
Due to incompatibility on some operating systems, the formatting of
some documents may not be preserved. We recommend the use of
PDF les to minimize formatting inconsistencies.
Your device can only wirelessly connect to one signal at a time. Therefore,
while your device is wirelessly connected to the KODAK iShow 1000 Pico
Projector, live streaming functions (such as YouTube ®and Facebook ®)
and web browsers will not be accessible on your device.
1. To project data wirelessly on the KODAK iShow 1000 Pico Projector, the
iShow (wireless projector) app and the les you wish to project
must be loaded on your device.
2. To download the iShow (wireless projector) app , turn on your
device and activate an internet connection. Open the App Store ®and
search for iShow (wireless projector) app . Download and install it
on your device.
3. To sync your documents, use your device’s data cable to connect your
device to the computer. Then, open iTunes ®on the computer.
4. Find your device name (iPhone, iPad or iPod touch) shown in the iTunes
screen and click on it to enter the device's [Summary] pane.
5. Once entering the device’s [Summary] pane, click the [Apps] on the top
command line. Find the iShow (wireless projector) app icon at the
lower side of the Apps pane and click the icon to add the les you would
like to project.
6. Once you have completed adding les, you may disconnect the device
from the computer.
7. To start projecting, rst ensure that your device’s wireless functionality is
turned on. Then, power on your KODAK iShow 1000 Pico Projector by
pressing the power button for 3 seconds.
Setup iShow (wireless projector) app
for projection

14
8. When the pico projector starts, your device’s wireless network will
automatically detect the signal “iShow-XXXX” (the signal name is the
same as the SSID name, which can be set by the user). Select this signal
and your device will connect to the projector.
9. Click on the installed iShow (wireless projector) app on your
device and the le selection pane will appear as shown below.
10. Select the le type you want to project by tapping the appropriate icon
(Documents, Pictures, or Video Files) at the top of the le selection pane.
11. Once the le type is selected, the appropriate les will appear. Tap the
le that you want to project. Once you have nished displaying this le,
return to the le selection pane to choose your next le.
For Android system
1. To project data wirelessly on the KODAK iShow 1000 Pico Projector, the
iShow (wireless projector) app and the les you wish to project
must be loaded on your device.
2. To download the iShow (wireless projector) app , turn on your
device and activate an internet connection. Open Google Play ®and
search for iShow (wireless projector) app . Download and install it
on your device.

15
3. To sync your documents, use your device’s data cable to connect your
device to the computer. Move the documents that you want to project
from your computer onto your device. If you prefer to wirelessly transfer
les to your device via email or other means, remember to download
and save them onto your device. Once they are saved to the device, the
iShow (wireless projector) app will automatically locate them.
4. Once you have completed adding les, you may disconnect the device
from the computer.
5. To start projecting, rst ensure that your device’s wireless functionality is
turned on. Then, power on your KODAK iShow 1000 Pico Projector by
pressing the power button for 3 seconds.
6. When the pico projector starts, your device’s wireless network will
automatically detect the signal “iShow-XXXX” (the signal name is the
same as the SSID name, which can be set by the user). Select this signal
and your device will connect to the projector.
7. Click on the installed iShow (wireless projector) app on your
device and the le selection pane will appear as shown below.
The rst time the iShow (wireless projector) app is used, the
scanning process may take some time to complete. The scanning
time varies by the version of Android and the number of les on the
device.
8. Select the le type you want to project by tapping the appropriate icon
(Documents, Pictures, or Video Files) at the top of the le selection pane.

16
9. Once the le type is selected, the appropriate les will appear. Tap the
le that you want to project. Once you have nished displaying this le,
return to the le selection pane to choose your next le.
For Windows system
1. Use enclosed CD-ROM to install iShow (wireless projector) app on
your computer.
2. Power on your KODAK iShow 1000 Pico Projector by pressing the power
button for 3 seconds.
3. When the pico projector starts, your computer’s wireless network will
automatically detect the signal “iShow-XXXX” (signal name is the same
as the SSID name, which can be set by the user). Select this signal and
your computer will be connected to the projector.
4. Click on the installed iShow (wireless projector) app on your
computer and the le selection pane will appear as shown below.
5. Click the setting button on the interface of iShow (wireless
projector) app. Select [Add File Folders] to add the folders you would
like to project. You can add up to 10 folders. You can also choose [Open
File] to select a single le in the le management system. Then click
[Send] to add it to the application.

17
6. Click the setting button again to return to the previous interface.
Select the le type you want to project by clicking the appropriate icon
(Documents, Pictures, or Video Files) at the top of the le selection pane.
7. Once the le type is selected, the appropriate les will appear. Click the
le that you want to project. Once you have nished displaying this le,
return to the le selection pane to choose your next le.
Transmission speeds of wireless network differ due to different
hardware congurations.
During your use of iShow (wireless projector) app, please use
genuine operating system, in order to ensure the normal operation of
the program.
iShow (wireless projector) app supports the use of cloud data.
However, when downloading from the cloud, the cloud software may
modify the name of the le.
To project Ofce les in Windows operating system, the following two
plug-ins must be installed for Microsoft Ofce 2007 or earlier versions:
.netframework3.5 download address:
http://www.microsoft.com/en-us/download/details.aspx?id=21
Microsoft Ofce 2007 plug-in download address:
http://www.microsoft.com/en-us/download/details.aspx?id=7

18
6
In iShow (wireless projector) app, tap the Setting button to congure
appropriate settings in iShow (wireless projector) app. The menu tree
where the following operations are found under the settings button vary by
device and version.
You can congure:
SSID
You may change the name of the wireless network. You may also set the
network security, and set the wireless network to open or encrypted mode.
If you forget the set SSID password, please press the reset hole
with a ne-like object and press the power button for 3 seconds
simultaneously, and then the projector will reboot and restore to
default Setting.
Hibernation / Sleep Mode
You can switch on the hibernation mode to set the continuous projection time
for longer battery life. The hibernation times that can be set are 10 mins, 15
mins, and 20 mins.
Set the application (available only
in wireless connection)

19
Keystone Correction
You can use and to apply keystone correction to the projected screen
in order to adjust it to a proper shape for easy viewing.
About
You can use this option to nd out the current version and copyright
information of your iShow (wireless projector) app.