Kogan KGNCMAVAA User manual

!!!!!!!!!KGNCMAVAA
$
!
!
USER!MANUAL!

Fully-automatic Coffee Machine USER MANUAL
When using electrical appliances, basic safety precautions should
always be followed, including the following:
1. Read all Instructions.
2. Do not touch hot surfaces. Use handles or knobs.
3. To protect against fire, electric shock and injury to persons do not
immerse cord, plugs, in water or other liquid.
4. Unplug from outlet when not in use and before cleaning. Allow to cool
before putting on or taking off parts, and before cleaning the appliance.
5. Do not operate any appliance with a damaged cord or plug or after the
appliance malfunctions, or has been damaged in any manner. Return
appliance to the nearest authorized service facility for examination,
repair or adjustment.
6. The use of accessory attachments not recommended or sold by the
appliance manufacturer may result in fire, electric shock or injury to
persons.
7. Do not use outdoors.
8. Do not let cord hang over edge of table or counter, or touch hot
surfaces.
9. Do not place on or near a hot gas or electric burner, or in a heated
oven.
10. To disconnect, turn any control to "off", Then remove plug from wall
outlet.
11. Do not use appliance for other than intended use.
12. Avoid contacting moving parts.
13. Don’t move the covering lid away when the appliance is in use.
14.Scalding may occur if the brewing unit is removed during the
brewing cycles.
IMPORTANT SAFEGUARDS SAVE THESE INSTRUCTIONS
If an extension cord is used:
(1) the marked electrical rating of the detachable power supply cord or
extension cord should be at least as great as the electrical rating of the
appliance;
(2) the appliance is of the grounded type, the extension cord should
be a grounding type 3-wire cord;
(3) the longer cord should be arranged so that it will not drape over the
countertop or tabletop where it can be pulled on by children or tripped
over.
This appliance is intended to be used in household and similar
applications such as:
– staff kitchen areas in shops, offices and other work environments
– farm houses
– by clients in hotels, motels and other residential type environments
– bed and breakfast type environments.

USER MANUAL
1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16 Dreg drawer
Machine components
Drip tray
Power cord
Milk-Frothing Device
Steam/hot water pipe
Coffee spout
Display
Cup warming plate
Water tank
Powder cover
Powder funnel
Adjusting knob
Coffee bean tank
Brewing door
Brewing unit
Dreg plate
15 14 13
1
2
4
5
6
7
8911
10
16
3
12
2
Hot water
Control panel
Steam
Add powder
Menu Power
Single Shot
Double Shot
Fully-automatic Coffee Machine
..
Fig. 2
Fig. 1

Table of Contents
1.Coffee machine introduction
1.1 Machine components
1.2 Control panel
1.3 Safety features of the coffee machine
1.4 Specifications
1.5 Accessories of the machine
2.Read before starting the coffee machine
2.1 Safety
2.2 Connect the power
3. How to use the machine
3.1 Install the machine
3.2 Discharge water
3.3 Operation
1.3.1
1.3.2 Impurity filter
2.1.1 Power line
2.1.2 Keep children away from the machine
2.1.3 Placement of the machine
2.1.4 Cleaning
2.1.5 Repair and maintain
3.3.1 Single Shot/Double Shot of coffee
3.3.2 Stop coffee brewing
3.3.3 Making coffee with coffee beans
3.3.4 Making coffee with coffee powder
Excessive powder protection
01
01
01
01
01
02
02
02
03
03
03
04
05
05
05
06
06
06
08
08
08
08
09
09
3.4 Suggestions
3.5 Program
3.6 Other indicators
3.7 Cleaning and maintenance
4. Troubleshooting
3.3.5 Milk-Frothing device
3.3.5.1 Frothing milk
3.3.5.2 Hot water
3.4.1 Pre-warm cups
3.4.2 Adjust coffee grind thickness
3.4.3 Adjust the height of coffee spout
3.4.4 Pre-brewing coffee
3.4.5 Coffee bean storage
3.4.6 Water quality
3.4.7 Working time
3.4.8 Turning off the power
3.5.1 Menu
3.7.1 Cleaning the main components
3.7.2 Cleaning the water tank filter
3.7.3 Storage
10
10
11
11
11
12
12
12
12
12
12
12
12
13
18
21
21
23
23
23
USER MANUAL
Fully-automatic Coffee Machine

01/02
If the user adds excessive powder, the machine will stop brewing after 2 seconds. Unnecessary
powder will be discharged, then machine will resume making coffee.
1.1 Machine components
See fig.1 above
1.2 Control panel
See fig.2 above
1.3 Safety features of the coffee machine
1.3.1 Excessive powder protection
1.3.2 Impurity filter
1.4 Specification parameters
1.5 Accessories included with the machine
.
1. Coffee machine introducton
The impurity filter in the grinder keeps unwanted sand and stones that may be contained in the
coffee beans away.These impurities may otherwise cause damage to the machine.If some
impurities still find their way into the grinder,they will cause the grinder to make unusually loud
noises and the coffee machine will shut off automatically after 20 seconds.If the grinder is
blocked by stone or sand,never try to take out the impurity yourself,please contact an authorized
USER MANUAL
Fully-automatic Coffee Machine
Rated voltage
Rated power
Size(L*W*H)
Net weight
Dreg cake
Exterior power cord
Temperature control
Coffee powder quantity
Coffee powder thickness
Water tank capacity
Coffee bean tank capacity
Steam/hot water exhaust range
Coffee spout height range
Overheat protection
Pump pressure
Compliance with EN bylaw
220-240V AC 50-60Hz
1250-1450W
415 x 320 x 365mm
12.0Kg
8PCS
0.9m
Digital control
program adjust
Manually adjusted, 3 settings
1.6L
200g
60°-70°
80-110mm
19 bar
EN 60335-1; EN 60335-2-14 ;EN 60335-2-15; EN 62233
Dual protection:temperature fuse and temperature sensor
CALIBRATION
0ML
- OG +
CALIBRATION
- 0ML +
OG
FIG. 5
FIG.3
40ML
-+
-+
..OK ESC
..
OK ESC
..
FIG. 4
Adjust powder quantity
For additional adjustments to coffee powder quantity, use the following instructions:
Check the machine before adjusting:
First, choose the coffee grind thickness level;
Check if there is coffee powder overflowing from the brewing unit, or there is too much
coffee powder in dreg plate.
Adjust powder quantity to the maximum, if there is still too little coffee powder in brewing
unit, the coffee powder quantity needs to be increased.
Adjust method:
Active: when coffee making is finished, before the LCD display shows 'ready for use', press
'MENU’ key (see FIG 3) and hold until LCD shows FIG 4, then press 'OK’ key to enter the
coffee powder quantity adjustment option(see FIG 5), in this mode, press '-' key to reduce
coffee powder quantity, up to -9G, press '+’ key to increase coffee powder quantity, up to
+9G; after adjustment, press 'OK' key to save and return to normal working condition. If you
do not want to adjust, then press 'ESC’ key to exit.
Passive: when making coffee, if there is too much coffee powder in brewing unit causing the
coffee powder to overflow, then the LCD would show FIG 5, in this mode, press '-' key to
reduce coffee powder quantity, up to -9G, press '+' key to increase coffee powder quantity,
up to +9G; after adjustment, press 'OK' key to save and return to normal working condition,
if you do not want to adjust, then press 'ESC’ key to exit.

Never use a damaged
power cord
Keep the cable away from
fire and hot surfaces
Never squeeze the
power cord
Keep the machine away from
fire and high temperatures
03/04
2. Read before starting the coffee machine
2.1 Safety
Hot water or steam
Do not touch the hot
water and steam exhaust
2.1.1 Power cord
Never use the coffee machine if the cord is damaged. If the power cord is damaged, it must be
replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a
hazard. Do not pass the cable around corners, over sharp edges or over hot surfaces and keep it
away from oil. Do not use the cable to carry or pull the machine. Do not remove the plug by
tugging on the cable and do not touch it with wet hands. Make sure the cable cannot drop freely
from tables or shelves.
2.1.2 Keep children away from the machine
Children are unaware of the danger that
electrical machines represent, therefore
children should never be left unsupervised with
the machine.
Never allow child to
play with the machine
Danger
This machine should only be operated by adults who have read and understood the manual.
Never touch the machine with the electrical objects as they can cause injury or death. Plug the
machine into a suitable electrical socket. The voltage must correspond to the voltage on the
rating plate.
Do not use the machine outdoors.
Avoid touching moving parts. (Lids of containers, brewing unit)
Don’t shake the machine when it is in working.
Scalding may occur if the protective parts of the machine (such as covering lids, funnel cover,
brewing door) are removed during the brewing cycles.
Warning
USER MANUAL
Fully-automatic Coffee Machine
The machine is an electrical appliance;there is risk
of short circuit and electric shock if it comes in
contact with water. Steam and hot water can scald
users; never aim hot water or steam at yourself or
others. Avoid touching steam and hot water
exhaust directly with your hands.
Do not make any technical changes of the
machine.
Unplug from outlet when not in use and before
cleaning. Allow to cool before putting on or taking
off parts, and before cleaning the machine. Don't
use the machine for any other purpose.
Please operate only as shown in the manual.

Place the machine on a flat and horizontal surface, and make sure it is inaccessible for children
or pets to avoid harm. The most appropriate temperature for operating the machine is between
10℃ to 35℃. Do not place the machine near hot surfaces or fire.
Place the machine on a level and
clean surface
Leave at least 100 mm
between the wall and the machine
05/06
2.1.4 Cleaning
Before cleaning, make sure that all switches have been turned off and unplug the coffee
machine. Then wait until the machine is cool before cleaning it. Never put the machine
under water.
2.1.5 Repair and maintenance
Unplug the machine immediately if it falls down. Do not operate the machine with a damaged
cord or plug or has been damaged in any manner. Manufacturer will not assume
responsibility for damage caused by unauthorised repair.
Use carbon dioxide extinguisher in case of fire.
Never use water or dry powder extinguisher.
Do not immerse the machine
in water or other liquid.
Use carbon dioxide
extinguisher
The coffee machine must be connected to an
AC outlet. Make sure the actual voltage
matches the rating voltage label on bottom of
the machine.
Never use a damaged cord or plug.
2.2 Connect the supply cord
Warning: Electric current can cause death!
Handle with care at all times.
Do not immerse plugs in water or other liquid.
Install the drip tray
3.How to operate the machine
3.1 Install the machine
Never start the machine if it does not contain water or coffee beans.
Put drip tray into the groove located in lower part of the
machine. Make sure the drip tray cover is correctly
positioned.
Plug into an AC outlet
2.1.3 Placement of machine
USER MANUAL
Fully-automatic Coffee Machine

Caution:
The drainage procedure should be carried out in
the following four cases:
The initial use of the machine
After the water tank was completely
emptied
The machine has not been use for a
long period of time.
Upon completion of the use of steam.
07/08
Discharge water
3.3 Operation
Touch the “single shot” button
or “double shot” button
to start making one shot or
two shots of coffee.
3.3.1 Single Shot/Double Shot of coffee
"ho t wate r" butt on
Take out water tank
and fill fresh water
to 3/4 capacity
Remove the water tank from the machine and fill it with
fresh water to 3/4 capacity. The valve in bottom of the
water tank is for water discharging. Gently press down
the water tank, then cover the lid to replacement.
Turn the steam/hot water exhaust towards the drip tray, place a cup under it, and then touch the
“OK” button by following the instructions on the screen. The machine will then start to pump
water out.
3.2 Discharge water
Use pure water only. Do not fill liquid other than water into the water tank.
In order to extend service life of the coffee machine, do not mix coffee bean with other material
(such as sugar and so on), otherwise the grinder will be damaged. These damages are not in the
scope of warranty.
Put coffee beans
into bean tank
Remove coffee bean tank cover and put the proper
quantity of coffee beans (no more than 200g) into the
container.
Untie the power cord, then connect to power supply,
touch the " "symbol press the power icon on the
Display. The screen shows “self test” first and then
“warming up”. Disappearance of the tiny dots
represents the boiler temperature reaches a higher
level. The machine will start rinsing after the boiler
reaches appropriate temperature. Please wait until a
“beep” and the screen shows standby , the machine has
finished preparing.
Caution:
3.3.2 Stop coffee brewing
The following adjustments can be made:
Powder quantity: Press “+” or “-“during grinding
process in order to adjust the quantity of coffee
powder.
Coffee quantity: Press “+” or “-“when coffee is
following out from the spout in order to adjust the
quantity of coffee liquid.
Both of the two adjustments will automatically be
saved.
Touch ESC key to terminate the coffee making
process.
USER MANUAL
Fully-automatic Coffee Machine
..
ESC
40ML
-+
-+
..

09/10
Touch the “add powder” button ,
Open the funnel cover [9] when fill powder icon
appears on the screen, fill a flat spoon of coffee
powder into the funnel, then touch either “Single
Shot” or “Double Shot” button to start making coffee.
3.3.4 Making coffee with coffee powder
1Touch the " add powder "
button
3Choose single shot
or double shot
The appropriate amount of coffee powder going to the funnel
should be no more than one flat spoon.
2Add appropriate amount
of coffee powder
One flat spoon
There are two methods to make coffee with the machine. Either coffee bean or coffee powder
can be used. In order to keep the freshness of the beans, the appropriate amount of beans will
be grinded to brew a cup of coffee.
3.3.3 Making coffee with coffee beans
Press steam button to
start heating up Turn the knob froth milk
Turn the knob for hot water Press the steam button
for steam
Fill milk into a milk jug, then pull the pipe out from the slot, and immerse it into the jug.
Place a mug under the device.
Touch the to start heating up, at this point please wait.
Once the steam is ready, turn the tiny knob on the device to milk frothing mode (See Fig.2), and
then the device will start frothing milk. Press the steam button on the machine to stop frothing
when the milk foam meets your expectation.
Please clean the device after use.
Fill fresh water into a jug, immerse the pipe into it, and press the steam button to start cleaning.
Refer Fig.3 to switch to hot water mode.
Refer Fig.4 to switch to steam mode.
3.3.5 Milk-Frothing Device
3.3.5.1 Frothing milk
USER MANUAL
Fully-automatic Coffee Machine
..
..
ESC
40ML
-+
-+
..

11/12
Suggest to pre-warm cup
3.4 Suggestions
Place cups above the cup warming plate to warm
them up.
Grinding grade need to be adjusted if either the coffee flows out too fast (coffee granules are too
big) or too slow (coffee granules are too small).
The adjustment can only be made during grinding,
otherwise the machine will be damaged.
The recommended grade is 2.
Turn the powder thickness adjust knob to a lower number
if the coffee granules are too big, turn the powder
thickness adjust knob to a higher number if the coffee
granules are too small. The recommended
grade is "2"
3.4.1 Pre-warm cups
3.4.2 Adjust coffee grind thickness
2
2
2
4
Place a cup under the
steam/hot water pipe [4]
Turn the knob to hot
water position
Press "-" OR "+" button
3.3.5.2 Hot Water
Steam/Hot water pipe is separated from coffee spout. Hot water can be used for making tea,
instant soup and so on.
Place a cup under the pipe and then refer to Fig.2 to switch to hot water mode. Touch
to start producing hot water. The temperature of hot water can be adjusted by touching "+"or"-"
during this period, there are three levels available. The maximum production of hot water is
250ML.
Adjust height of
coffee spout
Move the coffee spout up and down to make the spout a
little higher than the cup so as to keep the aroma of the
coffee.
The pump will stop for 2 second after the coffee powder has been wet , then continue.
To make sure that the coffee beans or coffee powder is fresh, put coffee beans into a sealed
container, then put the container in a cool, dark place.
Besides the coffee beans grinding and water temperature, water quality is also important. We
suggest treating the water with a water filter or purifier before putting it in the coffee machine.
The water in the water tank must be changed daily.
3.4.3 Adjust the height of the coffee spout
3.4.4 Pre-brewing coffee
3.4.5 Coffee bean storage
3.4.6 Water quality
The machine can work continuously all day.
Please wait until the machine is in “standby” mode before turning off the power.
3.4.7 Work time
3.4.8 Turning off the power
USER MANUAL
Fully-automatic Coffee Machine
..ESC
+
-
..
3Press the hot water button