Kogan KAESSPCOFFB User manual

ESPRESSO COFFEE MACHINE
(STAINLESS STEEL)
KAESSPCOFFB

•Read all the instructions in this user guide and store the user guide for future use.
•Ensure the wall outlet voltage corresponds to the rated voltage marked on the
rating plate.
•This appliance has been incorporated with a grounded plug. Ensure the wall outlet
in your house is well earthed.
•Do not immerse cord or plug in water or other liquid to avoid electric shock and
injury to persons.
•Remove plug from the wall outlet before cleaning and when not in use. Allow the
appliance to cool down completely before taking off, attaching other components,
or before cleaning.
•If the cord or plug is damaged, cease use immediately and contact Kogan.com
•Do not operate this appliance if the appliance malfunctions or is dropped or
damaged in any manner. Return appliance to the nearest authorised service
facility for examination, repair or electrical or mechanical adjustment.
•Do not use attachments that not recommended by Kogan.com. it may result in
fire, electric shock, or injury to persons.
•Place appliance on flat surface or table. Do not hang power cord over the edge of
table or counter.
•Ensure the power cord do not touch the hot surface of the appliance.
•Do not place the appliance on a hot surface or beside the fire to avoid damage.
•To disconnect, remove the plug from the wall outlet. Always hold the plug; never
pull the cord.
•Do not use the appliance for other than intended use and place it in a dry
environment.
•Close supervision is necessary when your appliance is being used near children.
•Use caution when operating the steam wand. Steam can reach very high
temperatures and may cause burns.
•Do not touch the hot surface of the appliance (such as a steam wand and the
steel mesh). Use handles or knobs.
•Do not let the appliance operate without water.
•Do not remove the Filter when the appliance is brewing coffee or making steam.
•Ensure the plug is in the wall outlet before using the appliance. Ensure to turn off
the switch before removing the plug from the wall outlet.
•This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities or lack of experience and knowledge unless
they have been given supervision or instruction concerning use of the appliances
by a person responsible for their safety.
SAFETY & WARNINGS

•Supervise children to ensure that they do not play with the appliance.
•This appliance is intended to be used in household and similar environments such
as:
oStaff kitchen areas in shops, offices, and other working environments.
oFarmhouses.
oBy clients in hotels, motels, and other residential type environments.
oBed and breakfast type environments.
•Do not use the appliance outdoors.
•If you plan to not use the product for a long time, you need to turn on the power to
release steam for 3 minutes before storing this product.
•If you stop power supply during steam release, the residual heat will make product
continue to release steam for a longer time. The appliance will stop releasing
steam immediately once you turn off steam knob.

A
Power Button
B
Thermometer
C
Top Cover
D
Pump Control Button
E
Coffee/Steam Selector
F
Steam Control Knob
G
Steam Wand
H
Frothing Device
I
Main Body
J
Water Tank Cover
K
Water Tank
L
Spoon
M
2-Cup Steel Mesh
N
Filter
O
Eject Switch
P
Filter Handle
Q
Water Float Switch
R
Removable Shelf
S
Drip Tray
O
OVERVIEW
R
A
D
B
G
E
H
I
J
C
F
Q
L
M
P
S
K
N

Main Body
Steam
Temperature
Indicator
Pump Control Button
Steam Control Knob
Coffee/Steam Selector
Coffee
Temperature
Indicator
Power Indicator
Power Button

Before the First Use
You should rinse the appliance with warm water. Follow the below instructions:
1. Pour water into the Water Tank, the water level should not exceed the MAX mark
in the tank. Then replace the Water Tank Cover.
2. Place the 2-Cup Steel Mesh into the Filter. Ensure there is no coffee in the steel
mesh.
3. Place a jug (not supplied) on the Removable Shelf. Make sure the Steam Control
Knob is off.
4. Connect to a power source, press the Power button, the power indicator is
illuminated.
5. Press the Pump Control button, the pump will pump water. When water is flowing
out, press the Pump Control button to close the pump.
6. Press the Coffee/Steam Selector and wait for a moment, the appliance begins
preheating. The coffee temperature indicator will be illuminated and that indicates
the preheating has been completed.
7. Press the Pump Control button and water will flow out.
8. After the water flow has stopped, you can pour the water that is collected in the
jug into each container and clean them thoroughly. Now you can start brewing.
Preheating
We recommend preheating the appliance before making coffee, including the funnel, filter,
and cup.
1. Remove the detachable Water Tank and open the Water Tank Cover to fill it with
water. The water level should not exceed the MAX mark in the tank. Then place
the tank into the appliance properly.
2. Set Steel Mesh into the Filter. Align the Filter with the groove in the appliance, then
insert the Filter into the appliance from the “Insert” position. Lock it into place by
turning firmly from "Insert" position, anticlockwise to the "Lock" position.
3. Place a cup on the Removable Shelf.
4. Then connect the appliance to the power supply. Make sure the Steam Control
Knob is off.
5. Press the Power button one time, the power indicator is illuminated. Press the
Coffee/Steam Selector.
INSTALLATION
Note: The appliance is supplied with a detachable tank for easy cleaning. Fill
the tank with water and then put the tank into the appliance.
Note: There may be noise when pumping the water for the first time, it is normal.
It is due to appliance releasing the air inside. After about 20 seconds, the noise
will disappear.

6. Press the Pump Control button, the pump will pump water. When water is flowing
out, press the Pump Control button immediately to close the pump. The purpose
of this step is to pump the water of the tank into the housing.
7. When the coffee temperature indicator is illuminated, you should press the Pump
Control button again, hot water will flow out. When the coffee temperature
indicator has extinguished, press the button to close the pump. Now the appliance
has been preheated.

Make Espresso
Make Espresso Coffee
1. After preheating, remove the Filter by turning it in clockwise. Add ground coffee
beans to the 2-Cup Steel Mesh with the Spoon, then press the grounds tightly with
the Tamper (opposite end of the spoon).
2. Set Steel Mesh into the Filter. Align the filter with the groove in the appliance, then
insert the filter into the appliance from the “Insert” position. Lock it into place by
turning firmly from "Insert" position, anticlockwise to the "Lock" position.
3. Place a cup on the Removable Shelf.
4. The coffee temperature indicator is illuminated, if it gets extinguished, wait for a
few minutes, it will be illuminated again. Press the Pump Control button and wait
for a few minutes and the coffee will start flowing out.
5. Press the Power button when desired coffee is obtained or the colour of coffee
changes. The indicator lights will turn off, and the appliance will finish pouring the
coffee.
6. After the coffee is ready, take out the Filter by turning it clockwise and then pour
the coffee residue out by releasing the Eject Switch on the Filter.
7. Let the steel mesh cool down completely, then rinse under running water.
Make Cappuccino or Frothed Milk
You can make a cup of cappuccino by adding frothed milk to a cup of espresso.
1. Prepare espresso as instructed in the Make Espresso Coffee section. Ensure that
the Steam Control Knob is at the “o” position.
2. Press the Coffee/Steam Selector, the coffee temperature indicator will be
illuminated, wait until the steam temperature indicator is illuminated.
3. Fill a jug with about 100 millilitres of milk for each cappuccino to be prepared. It is
recommended to use whole milk at refrigerator temperature.
4. Turn the Steam Control Knob anti-clockwise slowly, steam will come out of the
Frothing Device.
OPERATION
WARNING: Do not leave the appliance unattended while making the
coffee, as you may have to operate manually sometimes.
Note: During operation, the steam temperature indicator will cycle on and
off to maintain the desired temperature.
Note: Ensure the jug size is not less than 70±5mm. Ensure that the height
of the jug is good enough as the milk increases in volume by 2 times after
boiling.
Note: Never turn the Steam Control Knob rapidly, as the steam will
accumulate rapidly in a short time which may increase the risk of explosion.

5. Insert the Frothing Device about 2 centimetres into the milk, move the cup around
the device to froth milk.
6. When the frothed milk is ready, turn the Steam Control Knob back to “o” position.
7. Pour the frothed milk into the espresso that is already prepared. Now the
cappuccino is ready. Sweeten to taste and if desired, sprinkle the froth with a little
cocoa powder.
8. Press the Power button to stop the power supply. The indicator lights will turn off.
Make Steam
The Steam Wand can be used to make hot beverages like water, or tea.
1. Open the Top Cover. Remove the detachable Water Tank and fill it with desired
amount of water. The water level should not exceed the MAX mark in the tank.
Then place the tank into the appliance properly.
2. Replace the Top Cover and then connect the appliance to a power supply.
3. Press the Power button, the power indicator is illuminated.
4. Remove the Frothing Device from the Steam Wand.
5. Dip the Steam Wand into the liquid to be heated. Turn the Steam Control Knob
anti-clockwise slowly to start making steam.
6. When the required temperature is reached, you can turn the Steam Control Knob
to “o” position.
7. Press the Power button to stop the power supply.
Automatic Power off Function
If you do not perform any operation for 25 minutes, the appliance will turn off automatically.
Note: Allow the appliance to cool down for at least 5 minutes before making
coffee again. Otherwise, there might be burnt odour in your espresso coffee.
Note: Clean the steam outlet carefully with a wet sponge immediately after
the steam generation has stopped.

1. Remove the power supply and let the appliance cool down completely before
cleaning.
2. Clean the appliance’s main body with moisture-proof sponge. Clean the water
tank, drip tray and removable shelf regularly and dry them.
3. Detach the Filter by turning it clockwise. Remove the coffee residue. Clean it with
cleanser. Rinse with clear water.
4. Clean all the attachments with water and dry them thoroughly.
Cleaning Mineral Deposits
To make sure your appliance is operating efficiently, and internal piping is clean, clean
mineral deposits every 2 to 3 months. Follow the below instructions:
1. Fill the tank with water and descaling solution to the MAX level. The ratio of water
and descaling solution is 4:1. It is recommended to use homemade descaling
solution like citric acid (obtainable from chemists or drug stores). Add 3 millilitres of
citric acid to 100 millilitres of water.
2. Like in the preheating process, insert and lock the Filter into the appliance (no
ground coffee beans in it). Place a jug on the Removable Shelf.
3. Press the Power button, the power indicator will be illuminated.
4. Press the Pump Control button and Coffee/Steam Selector. When the water starts
flowing out, close the pump by pressing the Pump Control button and wait for a
few minutes. The heating of the appliance begins.
5. When the coffee temperature indicator is illuminated, it indicates the heating has
been completed. Press the Pump Control button and pump two cups of water
(about 2 ounce). Then close the pump and wait for 5 seconds.
6. Press the Coffee/Steam Selector. The coffee temperature indicator will extinguish,
wait until the steam temperature indicator is illuminated.
7. Make steam for 2 minutes by turning the Steam Control Knob and then turn the
Steam Control Knob to “o” position to stop making steam.
8. Press the Power button to stop the appliance immediately. Allow the descalers
deposit in the appliance for at least 15 minutes.
9. Restart the appliance and repeat the steps of 3-8 at least 3 times.
10. Press the Coffee/Steam Selector, the coffee temperature indicator will be
illuminated. Press the Pump Control button to brew until the descaler is
completely removed.
11. Press the Pump Control button to run the water mixture through the system.
Repeat the steps 3-8 for 3 times. This time it is not necessary to wait for 15 minutes
as instructed in step 8. Brew until no water is left in the tank.
12. Repeat step 11 at least 3 times to make sure the piping is clean.
CLEANING & CARE
Note: Do not clean with alcohol or solvent cleaner. Never immerse the
appliance’s main body in water for cleaning.

Problem
Possible Cause
Solution
The coffee maker will
not power on.
The power outlet is not
plugged in securely.
Plug the power cord into a wall
outlet correctly. If the appliance
still does not work, contact
Kogan.com
Metal parts in the
tank have rusted.
The descaler is not of
recommended type. It may
corrode the metal parts in
the tank.
Use the descaler recommended
by Kogan.com. See the
Cleaning and Care section of
this user guide.
Water leaks from the
bottom of the
appliance.
There is more water in the
drip tray.
Clean the drip tray.
The appliance is a
malfunctioning.
Contact Kogan.com
Water leaks from the
outer side of the
filter.
There is some ground
coffee beans on the filter
edge.
Remove the ground coffee
beans residue.
Acid (vinegar) taste
exists in Espresso
coffee.
Proper cleaning is not
performed after cleaning
mineral deposits.
Clean appliance before using it.
See the Getting Started section.
The ground coffee beans
are stored in a hot, wet
place for a long time. The
ground coffee beans might
have turned bad.
Use fresh ground coffee beans
or store the unused ground
coffee beans in a cool, dry place.
After opening ground coffee
beans package, reseal it tightly
and store it in a refrigerator to
maintain its freshness.
Plastic taste noted in
coffee.
Appliance is used for first
time. Test runs with hot
water is strongly
recommended before
making coffee.
Upon first use, run the coffee
machine with just hot water to
clean and prepare the
appliance. Do not drink the
initial test runs water. Ensure
appliance has been run by
adding water for at least one
minute before making coffee.
Burnt taste noted in
coffee.
Water is flowing through
the grinds too slowly,
leading to a bitter and
burnt taste.
Adjust your grinder for a coarser
grind of the beans.
Appliance is not
working.
Not plugged to wall outlet
correctly.
Plug the power cord into a wall
outlet correctly. If the appliance
still does not work, contact
Kogan.com
TROUBLESHOOTING

Disposal
No steam from the
nozzle on the steam
wand.
The nozzle on the steam
wand is blocked.
Use a toothpick or small, narrow
brush to remove possible
blockage. Ensure it is properly
cleaned after each use.
Cannot froth.
The steam temperature
indicator is not illuminated.
Only after the steam
temperature indicator is
illuminated, the steam can be
used to froth.
The container is too big, or
the shape is not correct.
Use a high and narrow cup.
You have used skimmed
milk.
Use whole milk or half-skimmed
milk.
This marking indicates that this appliance should not be disposed with other
house-hold wastes. To prevent possible harm to the environment or human
health from uncontrolled waste disposal, recycle it responsibly to promote the
sustainable reuse of material resources.

NOTES

Need more information?
We hope that this user guide has given you
the assistance needed for a simple set-up.
For the most up-to-date guide for your product,
as well as any additional assistance you may require,
head online to help.kogan.com