Kogan Ergolux ELSTD1MTMBA User manual

STANDING DESK ELECTRIC
SINGLE MOTOR - MEMORY
(BLACK/WHITE)
ELSTD1MTMBA/ELSTD1MTMWA

 Service Environment: 0–40°C
 Unplug the power plug before cleaning, wipe the dust on surface with a damp
cloth when cleaning and be careful not to let water drops into the internal parts or
loosen the connector.
 Check carefully to ensure correct and complete assembly before using.
 Familiarise yourself with all functions and program settings of the product before
first use.
 This product is not a toy. Do not allow children to play with the product or be
around it without supervision.
 Some slight noise caused by the belt or brake system is normal and will not have
any effect on the use of the equipment.
 Do not clean the equipment with corrosive or abrasive materials.
 This appliance can be used by children aged from 8 years and above and persons
with reduced physical, sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or instruction concerning use of the
appliance in a safe way and understand the hazards involved.
 If the supply cord is damaged, it must be replaced by the manufacturer, its service
agent or a similarly qualified person in order to avoid a hazard.
 Ensure there are no hazards in your operating environment: e.g., do not leave tools
around. Dispose of the plastic packaging materials as they may pose a choking
hazard to children.
 Keep the original package of the equipment if necessary in case of the future use in
transportation.
This marking indicates that this appliance should not be disposed with other
household wastes. To prevent possible harm to the environment or human health
from uncontrolled waste disposal, recycle it responsibly to promote the
sustainable reuse of material resources.
SAFETY & WARNINGS

OVERVIEW
Note:
The drawings below are only for reference and maybe slightly different from the product
you receive. If you are missing any parts or have any issues installing, please contact
Kogan.com.
LED Display
2
1
3
4
5
6
7
9
10
8
11

Part List:
No. Part Quantity
1 2 x Pedestal
2 1 x Column
31 x Column
4 1 x Supporting beam
5 1 x Transmission rod
6 2 x Supporting plate
7 1 x Control box
8 2 x Baffle

9. 1 x Control panel
10 1 x Power cable
11 4 x Cable tie
Control panel:
1. "▲" Adjust the desk upwards
2. "▼" Adjust the desk downwards
3. "1" Position 1, first height position saved by the user
4. "2" Position 2, second height position saved by the user
5. "3" Position 3, third height position saved by the user
6. "M" Height memory function
7. "A" Alert button to remind users changing posture

Step 1
Install pedestal (1).
Connect (1), (2) and (3) together: use 5x5 wrench (C) to tighten the screws (A).
Step 2
Install supporting beam (4).
INSTALLATION

Lay column (2) down as in picture 1 and install (4): use wrench (C) to tighten screws (B).
Install column (3) as in picture 2. Adjust the support to suit table top dimensions.
Step 3
Install transmission rod (5).
Install (5), (2) and (3), as in picture 1 first and then picture 2: use 2.5x2.5 wrench (D) to tighten.
Step 4

Install supporting plate (6).
Install (6), (2) and (3), use 5x5 wrench (C) to tighten the screws (A).
Step 5
Install control box (7) and control panel (9).
Distance between desktop edge and supporting should be not more than 200mm.
Install desktop with screw (F): use drill to tighten.
Step 6

Install baffle (8).
Install (8) using 2.5x2.5 wrench (D) to tighten the screws (E).
Connect all cables to the control box (7).
OPERATION
Control panel
Power port
Port for cable
connected to
the lifting column
7
9
10
11

Height Adjust Function
Press "▲" or "▼" to adjust the height. The LED display shows the current height.
Height Memory Function
a. Use "▲" or "▼" to set to the desired height. Press "M" to save the height and the
screen will display " ";
b. Press "1", "2" or "3" to store the height at that number.
c. Press "1", "2" or "3" to adjust the desk to the stored one.
Reminder Function
a. Press REMINDER button "A" to activate the function. The LED display shows
b. Two seconds later, press the "▲" or "▼" button to adjust the reminder time only
when the display screen flashes. The default time of the reminder is 45 minutes,
which is shown as "45". Then press any button to save the time setup or wait 5
seconds and system will save the time setup automatically. During the countdown,
any operation will lead to a repeat starting of the timer. When the countdown
finishes, display screen will show "00" and a beeping tone will be produced.
c. Within the 10-second reminder tone, press any button to reactivate the time
countdown that is set up in (b) step. If no operation takes place during the 10-
second reminder buzz, there will be another reminder buzz after 5 minutes. No
operation during the second buzz will turn off the reminder.
d. Press and hold the "A" button for three seconds to tum off the reminder. The LED
display will show " ".
TROUBLESHOOTING