Kogan Shangri-La SLSKYEMBWSA User manual

SKYE METAL AND WOOD
BED
SINGLE
SLSKYEMBWSA, SLSKYEMBOSA

1
Left vertical board (x1)
2
Right vertical board (x1)
3
Horizontal board (x2)
4 Top inner board (x1)
5 Bottom inner board (x1)
6 Upper end board (x1)
7 Centre board (x1)
8 Side frame pole (x2)
9 Middle frame pole (x1)
10a
Lower slat assembly (x1)
10b
Upper slat assembly (x1)
11
Large end board (x1)
12
Leg (x3)
13
Protective cover (x8)
14
Leg cover (x3)
COMPONENTS

Hardware
S4 M6 Allen key (x1) S5 M8 Allen key (x1) A M8 70mm screw (x8)
B M8 45mm screw (x12) C M6 16mm screw (x10) D M8 16mm screw (x4)
E M4 12mm screw (x10)

Step 1: Using the M8 Allen key (S5), secure left and right vertical boards (1, 2) to the
horizontal boards (3) and top inner board (4) with M8 45mm screws (B). Using the same
Allen key (S5), attach the bottom inner board (5) to the left and right vertical boards (1, 2)
with M8 16mm screws (D).
Place protective covers (13) on the top and bottom corners of this assembly.
S5 (x1) B(x12) D (x4)
ASSEMBLY
Note:
Do not use power tools when assembling this bed. Doing so may cause damage to the
components.
3
3
4
5
B
B
2
1
D
D
13
13
13
13

Step 2: Turn the assembly to the back. Using a Phillips screwdriver (not supplied), secure the
centre board (7) to the left and right vertical boards (1, 2) and top inner board (4) with M4
12mm screws (E).
E(x7)
4
2
1
7
E

Step 3: Place leg covers (14) under every leg (12). Align the screw holes on the legs (12) with
the screw holes on the middle frame pole (9). Using an M6 Allen key (S4), secure the legs
(12) to the middle frame pole (9) with M6 16mm screws (C).
This creates the leg assembly.
S4 (x1) C(x6)
9
C
C
C
12
12
12
14
14
14

A
C
8
8
Step 4: Align the holes on one end of the side frame poles (8) to the headboard. Using the
M8 Allen key (S5), secure the side frame poles (8) to the headboard with M8 70mm screws
(A).
Align the holes on one end of the leg assembly to the headboard. Using the M6 Allen key
(S4), secure the leg assembly to the headboard with M6 16mm screws (C).
S4 (x1) S5 (x1) A (x4) C (x2)

Step 5: Align the holes on the upper end board (6) to the large end board (11). Using a
Phillips screwdriver (not supplied), secure the upper end board (6) to the large end board (11)
with M4 12mm screws (E).
This creates the footboard assembly.
E (x4)
E
11
6

Step 6: Place protective covers (13) on the top and bottom corners of the footboard
assembly.This completes the footboard.
Align the holes on the other end of the side frame poles (8) to the footboard. Using the M8
Allen key (S5), secure the side frame poles (8) to the footboard with M8 70mm screws (A).
Align the holes on the other end of the leg assembly to the footboard. Using the M6 Allen
key (S4), secure the leg assembly to the footboard with M6 16mm screws (C).
S4 (x1) S5 (x1) A (x4) C (x2)
C
A
A
13
13
13
13
8
8