Kogan KA17SSMKETB User manual

1.7L STAINLESS STEEL
SMART KETTLE
KA17SSMKETB

•Read all instructions before using. Retain all instructions for future reference.
•The kettle is rated 220-240V~50-60Hz 1850-2200 W. Ensure to the voltage supply
at your home corresponds to this.
•Do not let the cord hang over the edge of a table or counter or touch a hot surface.
•Do not place on or near a hot gas or electric burner or in a heated oven.
•Do not operate the kettle without anything in it to avoid damaging the heat
elements.
•Ensure that the kettle is used on a firm and flat surface out of reach of children, this
will prevent the kettle from overturning and avoid damage or injury.
•To protect against a fire, electric shock, or personal injury, do not immerse cord,
electric plugs or kettle in water or other liquids.
•While water is boiling or just after the water has been boiled, avoid contacting with
steam from the spout.
•Always take care to pour boiling water slowly and carefully without tipping the
kettle too fast.
•Be careful of refilling when the kettle is hot.
•If the kettle is overfilled, boiling water may be ejected.
•Do not touch the hot surface. Use the handle or the button.
•The kettle is only to be used with the stand provided.
•Ensure that the kettle is switched off before removing it from its stand.
•The kettle must not be immersed into water.
•Use caution when moving the kettle containing hot water.
•Kettle can be used by persons with reduced physical, sensory or mental capabilities
or lack of experience and knowledge if they have been given supervision or
instruction concerning use of the kettle in a safe way and understand the hazards
involved.
•This kettle can be used by children aged from 8 years and above if they have been
given supervision or instruction concerning use of the kettle in a safe way and if
they understand the hazards involved.
•The kettle is not a toy. Do not let children play with it.
•The use of accessories, which are not recommended by the Kogan.com, may result
in fire, electric shock or personal injury.
•Unplug the kettle from the outlet when not in use and before cleaning. Allow the
kettle to cool before putting on or taking off parts and before cleaning the kettle.
SAFETY & WARNINGS

•To disconnect, turn the power switch to “off,” then remove plug from wall outlet.
•Do not use the kettle for other than intended use.
•Always ensure the lid is closed and do not lift it while the water is boiling. Scalding
may occur if the lid is removed during the brewing cycles.
•Do not use this kettle outdoors.
•This kettle is intended to be used in household and similar applications such as:
oStaff kitchen areas in shops, offices and other working environments;
oFarm houses;
oBy clients in hotels, motels and other residential type environments;
oBed and breakfast type environments.
•Follow the instructions in the Care & Cleaning section to clean this kettle.

OVERVIEW
Lid
Spout
Light Bar
Keep Warm Button
Temperature Buttons
Power Button
Water Level Gauge
Body
Power Base
Handle
Lid Release Button

Control Panel
Power Button To turn on or turn off the kettle.
70°C, 80°C,
90°C, 100°C
Temperature Buttons To p re -set the keep warm temperature. The
100°C button is used only for boiling.
Keep Warm Button To cancel the keep warm function.
Light Bar LED Display To display light.
Modes
Sleep Mode The light bar and other button indicator lights are turned off
Standby Mode If the kettle is placed on the base, the 100°C button indicator
light and light bar are turned on.
If the kettle is not placed on the base, the light bar blinks once
per second. The other buttons indicator lights are turned off.
Working Mode Depending on the temperature button selected, the indicator
light of that button, power button and light bar are turned on.
Keep Warm Mode Depending on the temperature button selected, the indicator
light of that button, keep warm button and light bar are turned
on. The power button indicator light is turned off.
OPERATION

Before Using Your Kettle
If you are using the kettle for the first time, it is recommended that you should clean your
kettle before use by boiling the Max capacity of water once and then discarding the water
twice. Wipe the surface with a damp cloth.
The maximum capacity of this kettle is 1.7 litres.
Using Kettle to Boil Water
1. Place the kettle and power base on a flat surface.
2. To fill the kettle, remove it from the power base and open the lid by pressing down
lid release button, then fill the kettle with the desired amount of water and close
the lid. The water level must be within the Min and the Max level. Too little water
will cause the kettle switching off before the water has boiled.
3. Plug into the power outlet, the light bar blinks.
4. Position the kettle on the power base, the light bar, and the 100°C button indicator
light is turned on.
5. If you do not want to select a pre-set temperature, you can press power button
directly, then the kettle starts heating and it will boil the water to 100°C. During the
heating process, the indicator lights of the 100°C button, the power button and the
light bar is turned on.
6. After heating, a beep can be heard. The kettle will stop working automatically.
Boiling Tips
•You can press the power button to stop the kettle during heating process.
•The kettle will enter sleep mode if you remove the kettle from the power base or no
operation for more than 3 minutes during heating process. Replace the kettle on
the power base and press any button, then the kettle will enter standby mode.
Note:
Do not fill the water over the ‘maximum’ line, as water may spill out of the spout
when boiling. Ensure that the lid is firmly in place before plugging the power
outlet.

Using Kettle with Pre-set Temperature
You can select a pre-set temperature using the temperature buttons. There are “70°C” or
“80°C” and “90°C” for selection.
1. Select a pre-set temperature, its corresponding indicator light is turned on.
2. Press the power button, the kettle starts heating.
3. When boiling the water to the pre-set temperature, a beep can be heard. The
kettle will stop heating and enter keep-warm mode automatically.
4. The kettle will keep the water warm for 30 minutes. The indicator lights of the
selected temperature button, the keep warm button and light bar are turned on
during this process.
5. After this process, all the indicator lights are turned off and the kettle enters sleep
mode. Press any button to make the kettle enter standby mode.
6. Lift the kettle from the power base and then pour the water.
Pre-set Temperature Tips
•The kettle will reheat the water to the pre-set temperature and then stop heating if
the water temperature is 5°C lower than the pre-set temperature during keeping
warm process. For example, if the pre-set temperature is 70°C, the kettle will reheat
the water to 70°C and then stop heating if the water temperature is lower than
65°C during keeping warm process.
•You can press the power button or keep warm button to stop the kettle from
keeping the water warm during keeping warm process.
•Under keeping warm condition, remove the kettle from the power base for more
than 3 minutes, then replace the kettle on the power base, the kettle will continue
to keep the water warm based on the pre-set temperature.
General Tips
•Hold and press the power button for 2 seconds, the kettle will enter sleep mode.
Press any button to make the kettle enter standby mode.
•The kettle may be stored on the power base when not in use.
•Always disconnect the power supply when not use.
Note:
Operate carefully when pouring the water from your kettle as boiling water may
result in scalding. Do not open the lid while the water in the kettle is hot.

Always disconnect the kettle from the power outlet and cool it down completely before
cleaning.
1. Never immerse/submerge the kettle, power cord or power base in water or allow
moisture to contact with these parts.
2. Wipe the appearance of body with a damp cloth or cleaner, never use a poisonous
cleaner.
3. Remember to clean the filter at intervals. For easier cleaning, detach the filter by
pressing down the tab of filter inside the kettle and then replace it after cleaning.
CAUTION: Do not use chemical, steel, wooden or abrasive cleaners to clean the
outside of the kettle to prevent the gloss loss.
Boil-Dry Protection
If you accidently let the kettle operate without water, when temperature sensor detects
temperature exceeding 105°C the kettle will stop heating. All of indicator lights will blink for
warning, if this occurs, allow the kettle to cool prior to filling with cold water before re-boiling.
Removal of Mineral Deposits
Your kettle should be periodically descaled as the mineral deposits in tap water may form
scale on the bottom of kettle, leading to less efficient operation. You can use a commercially
available descaler and follow the instructions on the package of descaler.
Alternatively, you may follow below instructions using white vinegar:
1. Fill the kettle with 3 cups of white vinegar, then adding water to the amount to
cover the bottom of kettle completely.
2. Leave the solution in the kettle overnight, then discard the solution.
3. Fill the kettle with clean water to the maximum position, run to boil, and then
discard the water.
4. Repeat step 3 several times until the odour of vinegar has been flushed away. Any
stains remaining inside the spout can be removed by rubbing with a damp cloth.
Disposal
This marking indicates that this appliance should not be disposed with other
house-hold wastes. To prevent possible harm to the environment or human
health from uncontrolled waste disposal, recycle it responsibly to promote
the sustainable reuse of material resources.
CLEANING & CARE

NOTES

Need more information?
We hope that this user guide has given you
the assistance needed for a simple set-up.
For the most up-to-date guide for your product,
as well as any additional assistance you may require,
head online to help.kogan.com