Kogan KAHUDA5CARA User manual

CAR HEAD UP DISPLAY
KAHUDA5CARA

Head up display (HUD)
Charging cable
Non-slip mat
Reflective film
User guide
COMPONENTS

Display (as viewed on windscreen)
1. Buzzer
2. Setting
3. Compass
4. Satellite
5. Speed
6. Light sensor
7. Speed unit (MPH/ Km/h)
OVERVIEW
Input
button

Before First Use
1. Place the non-slip mat on the driver’s side corner of the dashboard and then place
the head up display (HUD) on it.
2. Connect charger to vehicle’s 12V socket.
3. Connect the cable to the OBDII input on the unit.
4. Start the engine and the HUD will power on.
5. The RED satellite icon will flash when charged and begin searching for a satellite
connection. When the satellite indicator turns GREEN, the HUD is ready for use.
Reflective Film
The HUD projects information up onto the windscreen. Due to the construction of your
windscreen, the HUD may create a double reflection on the windscreen, which will make it
difficult to read. If this occurs, install the reflective film.
1. Spray some water onto the inside of your windscreen above where the HUD is
installed. Clean the area with a dry cloth.
2. Remove the backside (marked 1) of the film and apply to the windscreen.
3. Ensure the film is installed in the correct location and adjust if necessary.
4. Use a flat plastic object (credit card) to squeeze out any water or bubbles from
behind the reflective film.
5. Remove the protective film (marked 2).
6. If the reflective film isn’t positioned to display all the vehicle information, adjust the
position of the HUD and non-slip mat until it is correctly aligned.
INSTALLATION

Input button:
The Input button is a three-way button used to navigate the HUD’s menu and adjust the
settings.
• Up: push the button towards the windscreen
• Ok: press the button inwards
• Down: pull the button towards the driver
Using the input button
Press and hold the input button for 5 seconds to enter the menu. When finished adjusting
the settings, press and hold the input button for 5 seconds to save changes and exit.
• Up: increases setting value
• Down: decrease setting value
• Down and hold: turn alarm tone on or off
• Ok: short press to change menu selection
Factory Reset
Long pull up and hold. When all LEDs are illuminated, the HUD has been restored to
factory settings.
OPERATION
Up
Down
Ok

Settings menu
Since the HUD receives data from satellites, the data will vary slightly from the information
displayed on the vehicle dashboard. If you find the value on your dashboard is different to
the value displayed by the HUD, you can change it through the following procedure.
Menu
Parameter
Adjustment
range
Explanation
Default
Display
1
Speed
80-120
Up or down to adjust
107
2
Over-speed
alarm
10-180
Sounds alarm when
speed is exceeded
117
3
Brightness
0-5
1 (darkest) – 5 (brightest)
0 = Automatic
100
4
Speed unit
0-1
0= Km/h
1= MPH
50
5
Power on/off
voltage
100-150
Change to 13.2V-14V if
HUD does not turn off
automatically
45
6
Display mode
0-1
0 = reflect on windshield
1 = HUD screen
0

Working voltage
DC8-18V
Current
Working: 40mA
Standby: 15mA
Speed range
0-400km
Satellite positioning time
Cold start: 4 mins
Hot start: 45 seconds
Compass precision
±1°
12V car charger
1000mA
Weight
40g
Dimensions
90x54x12mm
SPECIFICATIONS

Issue
Solution
HUD has no display/power
• Ensure the power cable is properly connected
• Press the input button down multiple times
• Connect the HUD to a different 12V socket or
another vehicle to ensure the 12V is functioning
correctly
Inaccurate speed
• Ensure the speed unit is correct (MPH/Km/h)
• Adjust the speed value in the settings menu
HUD is not visible in sunlight
• Ensure the reflective film is installed
• Adjust the brightness in the settings menu
TROUBLESHOOTING

NOTES