Kohler MEMOIRS K-1418-H2 User manual

Features
•Acrylic
•Variable speed pump with 1.5 kW heater and back-lit
user keypad
•8 FlexjetTM whirlpool jets
•Less all trim
•72″(1829 mm) x 42″(1067 mm) x 22″(559 mm)
Codes/Standards Applicable
Specified model meets or exceeds the following:
•ASME A112.19.7
•UL 1795
•CSA B45.5/IAPMO Z124
•ASTM E162
•ASTM E662
6’ BATH WHIRLPOOL
K-1418-H2
Colors/Finishes
•0: White
•Other: Refer to Price Book for additional colors/finishes
Accessories
•0: White
•CP: Polished Chrome
•PB: Vibrant
®
Polished Brass
•NA: None applicable
•Other: Refer to Price Book for additional colors/finishes
Specified Model
Model Description Colors/Finishes
K-1418-H2 6’ bath whirlpool ❑0❑Other_____
Required Accessories
K-9698 Jet trim kit ❑CP ❑PB ❑Other_____
Recommended Accessories
K-7161-AF Pop-up bath drain ❑CP ❑PB ❑Other_____
Optional Accessories
K-1491 Pillow ❑0❑Other_____
K-1601 Footstop ❑0❑Other_____
K-1703 Remote control ❑NA
Product Specification
The acrylic bath whirlpool shall be 72″(1829 mm) in length, 42″(1067 mm) in width, and 22″(559 mm) in height. Product shall
have 8 FlexjetsTM, a variable-speed pump with 1.5 kW heater, and back-lit user keypad. Bath whirlpool shall be less all trim. Bath
whirlpool shall be Kohler Model K-1418-H2-______.
MEMOIRS
®
Page 1 of 2
1022383-4-D
USA/Canada: 1-800-4KOHLER
(1-800-456-4537)
www.kohler.com

Technical Information
Fixture*:
Basin area:
Bathing well 48″(1219 mm) x 27″(686 mm)
Top area 60″(1524 mm) x 30″(762 mm)
Weight 140 lbs (63.5 kg)
To overflow:
Water depth 16″(406 mm)
Capacity 94 gal (355.8 L)
* Approximate measurements for comparison only.
Drop-in
cut-out
70-1/2″(1791 mm) x 40-1/2″(1029 mm)
Pump: kW V Hz A
Variable-
speed:
1.5 240 50/60 11
Required Electrical Service
Dedicated circuit required, protected with Class A
Ground-Fault Circuit-Interrupter (GFCI) or Residual
Current Device (RCD):
Pump/control 220/240 V, 20 A, 50/60 Hz
Installation Notes
Install this product according to the installation guide.
Floor support under whirlpool must provide for a minimum of
43 lbs/square foot (209 kg/square meter) loading.
Hot water supply should be 70% of capacity or greater.
Installations will vary.
If installing a rim-mount faucet, make sure there is no
interference with drain overflow and circulating system before
drilling any holes. Consult local and national codes for
minimum air gap requirements if installing a spout on the
faucet deck.
This whirlpool is designed for drop-in installation only. It is not
suited for use in a three-wall alcove with an overhead shower.
No change in measurements if connected with drain
illustrated. (K-7161-AF or K-7161M-AF)
Pump/Control
34" (864 mm) W x 15" (381 mm) H
1-1/16" (27 mm)
1-1/2" OD
11-3/4"
(298 mm)
42" (1067 mm)
5-1/4" (133 mm)
36" (914 mm)
72" (1829 mm)
2-7/8" (73 mm)
3" (76 mm)
20-1/8"
(511 mm)
3" (76 mm)
22"
(559 mm)
Product Diagram
MEMOIRS
®
MEMOIRS
®
6’ BATH WHIRLPOOL
Page2of2
1022383-4-D