Kohler REVIVAL K-1375-RV User manual

Features
•Acrylic
•Variable speed pump with 1.5 kW heater, back-lit
user keypad and remote control
•6 FlexjetsTM
•Ten color-matched sequencing BodyssageTM backjets
•8 effervescent ports
•4 chromatherapy lights
•240 V, 20 A electrical service
•Drilled for required grab bars
•Coordinating Revival
®
Suite
•72″(1829 mm) x 42″(1067 mm) x 22″(559 mm)
Codes/Standards Applicable
Specified model meets or exceeds the following:
•ASME A112.19.7
•ASTM E662
•ASTM E162
•UL 1795
•CSA B45.5/IAPMO Z124
6’ EXPERIENCE BATH WHIRLPOOL
WITH SPA/MASSAGE PACKAGE
K-1375-LV
ALSO K-1375-RV
Colors/Finishes
•0: White
•Other: Refer to Price Book for additional colors/finishes
Accessories
•CP: Polished Chrome
•PB: Vibrant
®
Polished Brass
Specified Model
Model Description Colors/Finishes
K-1375-LV Bath whirlpool with Spa/Massage Package – pump on left ❑0❑Other_____
K-1375-RV Bath whirlpool with Spa/Massage Package – pump on right ❑0❑Other_____
Required Accessories
K-9653 Grab bars (pair) ❑CP ❑PB ❑Other_____
Recommended Accessories
K-7161-AF Adjustable pop-up drain ❑CP ❑PB ❑Other_____
Product Specification
The acrylic bath whirlpool shall be 72″(1829 mm) in length, 42″(1067 mm) in width, and 22″(559 mm) in height. Product shall
have 6 Flexjets, 8 effervescence ports, and 4 chromatherapy lights. Product shall have a variable speed pump, 1.5 kW heater,
back-lit user keypad and remote control. Product shall have 10 color-matched sequencing Bodyssage backjets and 2 pulsating
neckjets with pillow. Product shall be drilled for K-9653 grab bars (required) and UL listed. Product shall coordinate with Revival
®
Suite. Bath whirlpool shall be Kohler Model K-1375-_______-_______.
REVIVAL
®
Page 1 of 2
1023248-4-E
USA/Canada: 1-800-4KOHLER
(1-800-456-4537)
www.kohler.com

Technical Information
Fixture*:
Basin area:
Bathing area, bottom 40″(1270 mm) x 27″(686 mm)
Bathing area, top 61″(1549 mm) x 32″(813 mm)
Weight 165 lbs (75 kg)
To overflow:
Water depth 16″(406 mm)
Capacity 90 gal (341 L)
* Approximate measurements for comparison only.
Pump: kW V Hz A
1.5 240 50/60 15
Cut-out template 113311-7
Required Electrical Service
Dedicated circuit required, protected with Class A
Ground-Fault Circuit-Interrupter (GFCI) or Residual
Current Device (RCD):
Pump/control 220-240 V, 20 A, 50/60 Hz
Installation Notes
Install this product according to the installation guide.
Pump/piping protrudes beyond rim (see below).
Maximum deck thickness should not exceed 2″(50 mm).
Floor support under whirlpool must provide for a minimum of
44 lbs/square foot (214 kg/square meter) loading.
Hot water supply should be 70% of capacity or greater.
Installations will vary.
If installing a rim-mount faucet, make sure there is no
interference with drain overflow and circulating system before
drilling any holes. Consult local and national codes for
minimum air gap requirements if installing a spout on the
faucet deck.
1-1/2" OD
42"
(1067 mm)
6-1/2"
(165 mm)
2-7/8"
(73 mm)
3"
(76 mm)
3" (76 mm) x 24" (610 mm)
Flat Faucet Deck
2-1/4"
(57 mm)
36"
(914 mm)
72" (1829 mm)
Note: Pump/piping protrudes beyond rim.
Pump/Control Access
34" (864 mm) W x
15" (381 mm) H Min
22"
(559 mm)
3-1/2" (89 mm)
13-1/2"
(343 mm)
1" (25 mm) Max
4" (102 mm) Max
Recommended faucet area.
No change in measurements with drain
shown. (K-7167-AF)
Product Diagram
REVIVAL
®
REVIVAL
®
6’ EXPERIENCE BATH WHIRLPOOL WITH SPA/MASSAGE PACKAGE
Page2of2
1023248-4-E