Kohler Command Pro CH245 User manual

17 590 23 Rev. -- KohlerEngines.com
CH245, CH255, CH260, CH270, CH270TF,
CH395, CH395TF, CH440, CH440TF
Owner's Manual
IMPORTANT:
Read all safety precautions and instructions carefully before operating
equipment. Refer to operating instruction of equipment that this engine powers.
Ensure engine is stopped and level before performing any maintenance or
service.
Warranty coverage as outlined in the warranty card and on KohlerEngines.
com. Please review carefully as it provides your specifi c rights and obligations.
To maintain compliance with applicable emission regulations, exhaust system
backpressure may not exceed limits which can be found on KohlerEngines.
com. Search by Model No., then select Specs tab.
Kohler Engines has published CO2 values on KohlerEngines.com website.
Record engine information to reference when ordering parts or obtaining warranty coverage.
Engine Model
Specifi cation
Serial Number
Purchase Date
EN
DA
DE
ESE
ESS
FRC
FRF
HR
ID
IT
KO
NL
PL
PT
RO
RU
SL
ZH

2 17 590 23 Rev. --KohlerEngines.com
WARNING
Explosive Fuel
can cause fi res
and severe
burns.
Do not fi ll fuel
tank while
engine is hot or
running.
Gasoline is extremely
fl ammable and its vapors
can explode if ignited.
Store gasoline only in
approved containers, in
well ventilated, unoccupied
buildings, away from sparks
or fl ames. Spilled fuel
could ignite if it comes in
contact with hot parts or
sparks from ignition. Never
use gasoline as a cleaning
agent.
WARNING
Hot Parts can
cause severe
burns.
Do not touch
engine while
operating or just
after stopping.
Never operate engine with
heat shields or guards
removed.
WARNING
Rotating Parts
can cause
severe injury.
Stay away while
engine is in
operation.
Keep hands, feet, hair,
and clothing away from all
moving parts to prevent
injury. Never operate engine
with covers, shrouds, or
guards removed.
WARNING
Accidental
Starts can cause
severe injury or
death.
Disconnect and
ground spark
plug lead(s)
before servicing.
Before working on engine or
equipment, disable engine
as follows: 1) Disconnect
spark plug lead(s). 2)
Disconnect negative (–)
battery cable from battery.
WARNING
Carbon
Monoxide can
cause severe
nausea, fainting
or death.
Avoid inhaling
exhaust fumes.
Never run
engine indoors
or in enclosed
spaces.
Engine exhaust gases
contain poisonous carbon
monoxide. Carbon
monoxide is odorless,
colorless, and can cause
death if inhaled.
Safety Precautions
WARNING: A hazard that could result in death, serious injury, or substantial property damage.
CAUTION: A hazard that could result in minor personal injury or property damage.
NOTE: is used to notify people of important installation, operation, or maintenance information.
CAUTION
Electrical Shock
can cause injury.
Do not touch
wires while
engine is
running.
Symbols
Fuel Off On Choke Fast Slow
WARNING: This product can expose you to chemicals
including carbon monoxide and benzene, which are known
to the State of California to cause cancer and birth defects
or other reproductive harm. For more information go to
www.P65Warnings.ca.gov.

3
17 590 23 Rev. -- KohlerEngines.com
EN
E
D
H
F
K
L
J
I
A
B
M
OR
P
Q
C
G
N
AAir Cleaner
Cover BBail CFuel Cap DFuel Tank
EThrottle Lever FOn/Off Switch
(if equipped) GDipstick/Oil Fill Plug HOil Drain Plug
IRetractable
Starter JStarter Handle KFuel Shut-Off
(and Ignition, if
equipped) LChoke Lever
M
2:1 with Clutch
Reduction
System
(CH245,
CH255, CH270,
CH395, CH440)
NDrain Plug OGear Box
Dipstick P
6:1 Reduction
System
(CH245,
CH255, CH270)
QOil Level/Drain
Plug ROil Fill Plug
See next page for exploded view of air cleaner systems.
Visit KohlerEngines.com for service parts information and purchasing options.

4 17 590 23 Rev. --KohlerEngines.com
H
I
B
F
G
F
E
D
B
C
C
A
J
P
O
L
Q
F
B
C
K
K
M
M
N
P
O
L
Q
F
B
C
K
K
M
M
S
R
AQuad-Clean™
Air Cleaner B Air Cleaner Cover CBail DPrecleaner
EPaper Element FAir Cleaner
Base GLow-Profi le Air Cleaner HScrew
IFoam Element JCH270 Oil Bath
Air Cleaner KO-Ring LFoam Filter Cover
MFoam Filter
Support Plate NFoam Filter OOil Retainer Ring POil Reservoir Cup
QOil Level Mark RCH395/CH440 Oil Bath Air
Cleaner SFoam Element
Kit
Pre-Start Checklist
1. Check oil level. Add oil if low. Do not overfi ll.
2. Check fuel level. Add fuel if low. Check fuel system components and lines for leaks.
3. Check and clean cooling areas, air intake areas and external surfaces of engine (particularly
after storage).
4. Check that air cleaner components and all shrouds, equipment covers, and guards are in place
and securely fastened.
5. Check spark arrestor (if equipped).
6. If equipped with oil bath air cleaner, check oil level in oil reservoir cup; add oil if below oil level
mark; do not overfi ll; inspect for leaks. See Oil Bath Air Cleaner.

5
17 590 23 Rev. -- KohlerEngines.com
EN
Starting
WARNING
Carbon Monoxide can cause
severe nausea, fainting or death.
Avoid inhaling exhaust fumes.
Never run engine indoors or in
enclosed spaces.
Engine exhaust gases contain poisonous
carbon monoxide. Carbon monoxide is
odorless, colorless, and can cause death if
inhaled.
WARNING
Rotating Parts can cause severe
injury.
Stay away while engine is in
operation.
Keep hands, feet, hair, and clothing away
from all moving parts to prevent injury. Never
operate engine with covers, shrouds, or
guards removed.
NOTE: Choke position for starting may vary
depending upon temperature and other
factors. Once engine is running and
warm, turn choke to OFF position.
NOTE: Extend starter cord periodically to
check its condition. If cord is frayed
have it replaced immediately by a
Kohler authorized dealer.
NOTE: Do not crank engine continuously for
more than 10 seconds. Allow a 60
second cool down period between
starting attempts. Failure to follow
these guidelines can burn out starter
motor.
NOTE: If engine develops suffi cient speed to
disengage starter but does not keep
running (a false start), engine rotation
must be allowed to come to a complete
stop before attempting to restart
engine. If starter is engaged while
fl ywheel is rotating, starter pinion and
fl ywheel ring gear may clash, resulting
in damage to starter.
1. Turn fuel shut-off valve to ON position (if
equipped).
2. Turn engine on/off switch to ON position (if
equipped).
3. Start engine as follows:
Cold engine: Place throttle control midway
between SLOW and FAST positions. Place
choke control into ON position.
Warm engine: Place throttle control midway
between SLOW and FAST positions. Return
choke to OFF position as soon as engine
starts. A warm engine usually does not
require choke on.
4. Retractable Start: Slowly pull starter handle
until just past compression-STOP! Return
starter handle; fi rmly pull straight out to avoid
excessive rope wear from starter rope guide.
Electric Start: Activate starter switch.
Release switch as soon as engine starts. If
starter does not turn engine over, shut off
starter immediately. Do not make further
attempts to start engine until condition is
corrected. Do not jump start. See your Kohler
authorized dealer for trouble analysis.
5. Gradually return choke control to OFF
position after engine starts and warms up.
Engine/equipment may be operated during
warm up period, but it may be necessary to
leave choke partially on until engine warms
up.
Cold Weather Starting Hints
1. Use proper oil for temperature expected.
2. Disengage all possible external loads.
3. Use fresh winter grade fuel. Winter grade
fuel has higher volatility to improve starting.
Stopping
1. If possible, remove load by disengaging all
PTO driven attachments.
2. If equipped, move throttle control to slow or
idle position; stop engine.
3. If equipped, close fuel shut-off valve.
Angle of Operation
Refer to operating instructions of equipment
this engine powers. Do not operate this engine
exceeding maximum angle of operation; see
specifi cation table. Engine damage could result
from insuffi cient lubrication.
Engine Speed
NOTE: Do not tamper with governor setting to
increase maximum engine speed.
Overspeed is hazardous and will void
warranty.
High Altitude Operation
If this engine is operated at an altitude of 4000
ft. (1219 meters) or above, a high altitude
carburetor kit is required. To obtain high altitude
carburetor kit information or to fi nd a Kohler
authorized dealer, visit KohlerEngines.com or
call 1-800-544-2444 (U.S. and Canada).
This engine should be operated in its original
confi guration below 4000 ft. (1219 meters).
Operating this engine with the wrong engine
confi guration at a given altitude may increase
its emissions, decrease fuel effi ciency and
performance, and result in damage to the
engine.

6 17 590 23 Rev. --KohlerEngines.com
Carburetor Icing
NOTE: Running engine with cover positioned for cold weather operation in normal conditions can
damage engine.
Carburetor icing can take place when certain combinations of temperature and humidity exist.
Result of carburetor icing is rough running at idle or low speed as well as black or white smoke.
To reduce likelihood of carburetor icing, air cleaner cover can be rotated to draw warmer air from
muffl er side. For cold weather operation, position air cleaner cover with snowfl ake decal out.
For normal operation, position air cleaner cover with sun decal out.
Maintenance Instructions
WARNING Before working on engine or equipment, disable
engine as follows: 1) Disconnect spark plug
lead(s). 2) Disconnect negative (–) battery cable
from battery.
Accidental Starts can cause
severe injury or death.
Disconnect and ground spark
plug lead(s) before servicing.
Normal maintenance, replacement or repair of emission control devices and systems may be
performed by any repair establishment or individual; however, warranty repairs must be performed
by a Kohler authorized dealer found at KohlerEngines.com or 1-800-544-2444 (U.S. and Canada).
Maintenance Schedule
After fi rst 5 Hours
● Change engine oil.
Every 8 Hours
● Check oil bath air cleaner oil level in oil reservoir cup (if equipped).
Every 50 Hours
● Change oil in 2:1 with Clutch Reduction System (CH245, CH255, CH270, CH395, CH440).
Every 50 Hours¹
● Service/replace oil bath air cleaner foam fi lter or foam elements (if equipped).
Every 50 Hours or Annually (whichever comes fi rst)
● Service/replace Quad-Clean™ precleaner.
Every 100 Hours or Annually¹ (whichever comes first)
● Clean low-profi le air cleaner element.
● Change engine oil.
● Clean cooling areas.
Every 200 Hours
● Replace Quad-Clean™ air cleaner element.
Every 300 Hours
● Replace low-profi le air cleaner element.
● Check fuel fi lters (tank outlet fi lter and in-line fi lter) and clean or replace if needed (if equipped).
● Change oil in 6:1 Reduction System (CH245, CH255, CH270).
Every 300 Hours²
● Check and adjust valve clearance when engine is cold.
Every 500 Hours or Annually¹ (whichever comes first)
● Replace spark plug and set gap.
1 Perform these procedures more frequently under severe, dusty, dirty conditions.
2 Have a Kohler authorized dealer perform this service.

7
17 590 23 Rev. -- KohlerEngines.com
EN
Oil Recommendations
We recommend use of Kohler oils for best
performance. Other high-quality detergent
oils (including synthetic) of API (American
Petroleum Institute) service class SJ or higher
are acceptable. Select viscosity based on air
temperature at time of operation as shown in
table below.
°F -20 020324060
50 80 100
°C -30 -20 -10 0 10 20 30 40
5W-30
10W-30
SAE 30
Check Oil Level
NOTE: To prevent extensive engine wear or
damage, never run engine with oil level
below or above operating range
indicator on dipstick.
Ensure engine is cool and level. Clean oil fi ll/
dipstick areas of any debris.
1. Remove dipstick; wipe oil off .
2. Reinsert dipstick into tube; rest on oil fi ll
neck; turn counterclockwise until cap drops
down to lowest point of thread leads; do not
thread cap onto tube.
a. Remove dipstick; check oil level.
For CH260/CH270 engines, oil level
should be at middle of indicator on
dipstick.
For all other models, oil level should be
at top of indicator on dipstick.
or
b. Remove oil fi ll plug.
For CH260/CH270 engines, oil level
should be to middle of fi ller neck threads.
For all other models, oil level should be
up to point of overfl owing fi ller neck.
3. If oil is low, add oil to specifi ed level on
dipstick or fi ller neck threads for engine being
serviced. See step 2.
4. Reinstall dipstick or oil fi ll plug and tighten
securely.
Change Oil
Change oil while engine is warm.
1. Clean area around oil fi ll cap/dipstick and
drain plug.
2. Remove drain plug and oil fi ll cap/dipstick.
Drain oil completely.
3. Reinstall drain plug. Torque to 13 ft. lb.
(17.6 N·m).
4. Fill crankcase with new oil to specifi ed level
on dipstick or fi ller neck threads for engine
being serviced. See Check Oil Level.
5. Reinstall oil fi ll cap/dipstick and tighten
securely.
6. Dispose of used oil in accordance with local
ordinances.
Oil Sentry™ (if equipped)
This switch is designed to prevent engine
from starting in a low oil or no oil condition. Oil
Sentry™ may not shut down a running engine
before damage occurs. In some applications
this switch may activate a warning signal. Read
your equipment manuals for more information.
Reduction Systems (if equipped)
Some engines are equipped with a gear
reduction system. Follow maintenance and oil
change information specifi ed in this section and
maintenance schedule.
2:1 Reduction System (CH270)
This reduction system is lubricated by engine
crankcase oil. No special maintenance or
service is necessary. Check and maintain
engine oil level as outlined in Check Oil Level.
2:1 with Clutch Reduction System (CH245,
CH255, CH270, CH395, CH440)
NOTE: Engines with this reduction system
must be operated at 2400 RPM or
higher under load, when full gear box
engagement occurs. Operating engine
under heavy loads below 2400 RPM,
could result in clutch/gear box failure
from disc slippage/overheating and
insuffi cient engine cooling, not covered
under normal warranty.
This reduction system uses a clutch assembly
and chain and sprocket drive system,
independent of, and separated from main
crankcase lubrication. Check and maintain oil
level using dipstick in gear box case. Change
reduction system oil at interval in maintenance
schedule. Use 20W-40 or 20W-50 oil in this
gear box case. Oil capacity of this gear box is
0.5 L (0.52 U.S. qt.).
1. Drain old oil out through oil drain plug of gear
box cover, tip engine as required. Reinstall
drain plug and tighten securely.
2. Engine must be level. Add new 20W-40 or
20W-50 oil through oil dipstick hole on top of
gear box case until oil level is up to bottom of
the mark on the oil dipstick in gear box case.
Reinstall dipstick securely into gear box
cover.

8 17 590 23 Rev. --KohlerEngines.com
Add Fuel
WARNING
Explosive Fuel can cause fi res
and severe burns.
Do not fi ll fuel tank while engine is
hot or running.
Gasoline is extremely fl ammable and
its vapors can explode if ignited. Store
gasoline only in approved containers, in
well ventilated, unoccupied buildings, away
from sparks or fl ames. Spilled fuel could
ignite if it comes in contact with hot parts or
sparks from ignition. Never use gasoline as a
cleaning agent.
Ensure engine is cool.
1. Clean area around fuel cap.
2. Remove fuel cap. Fill to base of fi ller neck.
Do not overfi ll fuel tank. Leave room for fuel
to expand.
3. Reinstall fuel cap and tighten securely.
Fuel Line
Low permeation fuel line must be installed on
carbureted Kohler Co. engines to maintain EPA
and CARB regulatory compliance.
Fuel Valve
Engines are equipped with a fuel valve
and integral screen fi lter located at inlet of
carburetor. It controls and fi lters fuel fl ow from
tank to carburetor. Clean fuel valve cup of
debris.
1. Remove two nuts, two screws, and
carburetor cover panel.
2. Turn fuel valve lever to OFF position.
3. Remove fuel valve cup. Remove O-ring and
fi lter screen.
4. Clean screen and fuel valve cup with solvent
and wipe it off .
5. Check screen and O-ring, replace if
damaged.
6. Reinstall O-ring followed by fuel valve cup.
Rotate fuel valve cup until it is fi nger tight.
Turn with a wrench 1/2 to 3/4 full turn.
7. Turn fuel valve to ON position and check for
leaks. If fuel valve leaks repeat steps 5 & 6.
8. Tighten fuel cap securely.
9. Reinstall carburetor cover panel securing
with hardware removed in step 1.
6:1 Reduction System (CH245, CH255,
CH270)
This reduction system uses an internal pinion
and ring gear system, independent of, and
separated from main crankcase lubrication.
Check and maintain oil level using oil level/
drain plug hole in gear box case. Change
reduction system oil at interval in maintenance
schedule. Oil capacity of this gear box is 0.12 L
(0.13 U.S. qt.).
1. Drain old oil out through oil level/drain plug,
tip engine as required.
2. Engine must be level. Add new oil through oil
fi ll plug hole on top until oil level is up to
bottom of oil level/drain plug hole. Reinstall
both plugs and tighten securely.
6:1 Reduction System (CH395, CH440)
This reduction system is lubricated by engine
crankcase oil. No special maintenance or
service is necessary. Check and maintain
engine oil level as outlined in Check Oil Level.
Fuel Recommendations
WARNING
Explosive Fuel can cause fi res
and severe burns.
Do not fi ll fuel tank while engine is
hot or running.
Gasoline is extremely fl ammable and
its vapors can explode if ignited. Store
gasoline only in approved containers, in
well ventilated, unoccupied buildings, away
from sparks or fl ames. Spilled fuel could
ignite if it comes in contact with hot parts or
sparks from ignition. Never use gasoline as a
cleaning agent.
NOTE: E15, E20 and E85 are NOT approved
and should NOT be used; eff ects of
old, stale or contaminated fuel are not
warrantable.
Fuel must meet these requirements:
● Clean, fresh, unleaded gasoline.
● Octane rating of 87 (R+M)/2 or higher.
● Research Octane Number (RON) 90 octane
minimum.
● Gasoline up to 10% ethyl alcohol, 90%
unleaded is acceptable.
● Methyl Tertiary Butyl Ether (MTBE) and
unleaded gasoline blend (max 15% MTBE by
volume) are approved.
● Do not add oil to gasoline.
● Do not overfi ll fuel tank.
● Do not use gasoline older than 30 days.

9
17 590 23 Rev. -- KohlerEngines.com
EN
Spark Plugs
CAUTION
Electrical Shock can cause injury.
Do not touch wires while engine
is running.
Clean out spark plug recess. Remove plug and
replace.
1. Check gap using wire feeler gauge. Adjust
gap, see specifi cation table for adjustment.
2. Install plug into cylinder head.
3. Torque plug to 20 ft. lb. (27 N·m).
Air Cleaner
NOTE: Running engine with cover positioned
for cold weather operation in normal
conditions can damage engine.
NOTE: Operating engine with loose or
damaged air cleaner components
could cause premature wear and
failure. Replace all bent or damaged
components.
NOTE: Paper element cannot be blown out
with compressed air.
Quad-Clean™
Move bails on air cleaner cover down; remove
latches from under tabs on base; remove cover.
or
Turn air cleaner cover (counterclockwise) to
release tabs inside cover from base; remove
cover.
Precleaner:
1. Remove precleaner from paper element.
2. Replace or wash precleaner in warm water
with detergent. Rinse and allow to air dry.
3. Lightly oil precleaner with new engine oil;
squeeze out excess oil.
4. Reinstall precleaner over paper element.
Paper Element:
1. Separate precleaner from element; service
precleaner and replace paper element.
2. Install new paper element on base; install
precleaner over paper element.
Position air cleaner cover for normal operation
(sun decal out) or cold weather operation
(snowfl ake decal out).
Place latches under tabs on base; lift up bails to
secure cover.
or
Turn air cleaner cover (clockwise) to secure
tabs inside cover in base.
Low-Profi le
1. Remove screw and air cleaner cover.
2. Remove foam element from base.
3. Wash foam element in warm water with
detergent. Rinse and allow to air dry.
4. Lightly oil foam element with new engine oil;
squeeze out excess oil.
5. Reinstall foam element into base.
6. Reinstall cover and secure with screw.
Oil Bath
Some engines are equipped with an oil bath
air cleaner. Follow maintenance and oil change
information specifi ed in this section and in
Maintenance Schedule.
Move bails on air cleaner cover down; remove
latches from under tabs on base; remove cover.
1. Remove foam fi lter cover from oil reservoir
cup. Remove foam fi lter support plate and
foam fi lter or foam elements.
2. CH270 engines: Replace or wash foam fi lter
in warm water with detergent. Rinse and
allow to air dry.
CH395/CH440 engines: Replace or wash
foam elements in warm water with detergent.
Rinse and allow to air dry.
3. Lightly oil foam fi lter or foam elements with
new engine oil; squeeze out excess oil.
4. Remove foam fi lter support plate and oil
retainer ring from oil reservoir cup.
5. Remove oil reservoir cup from base. Empty
oil from cup and wash cup in warm water
with detergent. Rinse and dry cup.
6. Make sure O-ring is in place on air cleaner
base. Set oil reservoir cup on base.
7. Fill oil reservoir cup up to oil level mark with
same grade of oil as in crankcase. See Oil
Recommendations.
8. Reinstall oil retainer ring and foam fi lter
support plate in oil reservoir cup.

10 17 590 23 Rev. --KohlerEngines.com
9. CH270 engines: Reinstall foam fi lter on oil
reservoir cup. Place foam fi lter support plate
on fi lter. Reinstall foam fi lter cover. Make
sure O-ring is in place on top of fi lter cover.
CH395/CH440 engines: Reinstall taller foam
element fi rst, then shorter foam element on
oil reservoir cup. Place foam fi lter support
plate on elements. Reinstall foam fi lter cover.
Make sure O-ring is in place on top of fi lter
cover.
Position air cleaner cover for normal operation
(sun decal out) or cold weather operation
(snowfl ake decal out). Place latches under tabs
on base; lift up bails to secure cover.
Breather Tube
Ensure both ends of breather tube are properly
connected.
Air Cooling
WARNING
Hot Parts can cause severe
burns.
Do not touch engine while
operating or just after stopping.
Never operate engine with heat shields or
guards removed.
Proper cooling is essential. To prevent over
heating, clean screens, cooling fi ns, and other
external surfaces of engine. Avoid spraying
water at wiring harness or any electrical
components. See Maintenance Schedule.
Repairs/Service Parts
We recommend that you use a Kohler
authorized dealer for all maintenance,
service, and replacement parts for engine.
To fi nd a Kohler authorized dealer visit
KohlerEngines.com or call 1-800-544-2444
(U.S. and Canada).
Storage
If engine will be out of service for 2 months or
more follow procedure below.
1. Add Kohler PRO Series fuel treatment or
equivalent to fuel tank. Run engine 2-3
minutes to get stabilized fuel into fuel system
(failures due to untreated fuel are not
warrantable).
2. Change oil while engine is still warm from
operation. Remove spark plug(s) and pour
about 1 oz. of engine oil into cylinder(s).
Replace spark plug(s) and crank engine
slowly to distribute oil.
3. If engine is equipped with oil bath air cleaner,
clean and oil foam fi lter or foam elements
and replace oil in oil reservoir cup. See Oil
Bath Air Cleaner.
4. Disconnect negative (-) battery cable.
5. Store engine in a clean, dry place.

11
17 590 23 Rev. -- KohlerEngines.com
EN
Engine Specifi cations
Model Bore Stroke Displacement Oil Capacity
(Refi ll) Spark Plug
Gap
Maximum Angle
of Operation
(@ full oil level)*
CH245 2.7 in.
(68 mm) 1.9 in. (49 mm) 10.8 cu. in. (177 cc)
0.63 U.S. qt.
(0.60 L)
0.030 in.
(0.76 mm) 25°
CH255
CH260 2.8 in.
(70 mm) 2.1 in. (54 mm) 12.7 cu. in. (208 cc)
CH270
CH270TF
CH395
CH395TF
3.1 in.
(78 mm) 2.3 in. (58 mm) 16.9 cu. in. (277 cc) 1.16 U.S. qt.
(1.1 L)
CH440
CH440TF
3.5 in.
(89 mm) 2.7 in. (69 mm) 26.2 cu. in. (429 cc)
*Exceeding maximum angle of operation may cause engine damage from insuffi cient lubrication.
Additional specifi cation information can be found in service manual at KohlerEngines.com.
Any and all horsepower (hp) references by Kohler are Certifi ed Power Ratings and per SAE J1940
& J1995 hp standards. Details on Certifi ed Power Ratings can be found at KohlerEngines.com.
Emission Control System
Exhaust Emission Control System for models CH245, CH255, CH260, CH270, CH270TF, CH395,
CH395TF, CH440, CH440TF is EM for U.S. EPA, California, and Europe. This engine is certifi ed to
operate on gasoline.
NOTE: Tampering with the engine and its emission control system voids the EPA Certifi cate of
Conformity, ARB Executive Order, and EU type-approval.
Possible Cause
Problem No
Fuel Improper Fuel
Dirt In
Fuel
Line
Dirty
Debris
Screen Incorrect Oil Level Engine Overloaded Dirty Air Cleaner
Faulty
Spark
Plug
Will Not Start ●●● ● ● ● ●
Hard Starting ●● ●●●●
Stops Suddenly ● ●●●●●●
Lacks Power ●●●● ● ● ●
Operates Erratically ●●● ● ● ●
Knocks or Pings ●● ● ●
Skips or Misfi res ●●● ● ●
Backfi res ●● ● ● ●
Overheats ●●●● ● ●
High Fuel
Consumption ●●●
Troubleshooting
Do not attempt to service or replace major engine components, or any items that require special
timing or adjustment procedures. This work should be performed by a Kohler authorized dealer.