Kohler Memoirs Stately 3 Hole Basin Mixer User manual

P3907005
MemoirsStately3HoleBasin
Mixer
Installation and User Guide
MODEL NUMBERS
454W–3S 454W–4S 454W-4V
Important :- Please quote the above model number(s) when ordering spares.
IMPORTANT!
Installer: This manual is the property of the customer and must
be retained with the product for maintenance and operational
purposes.

CONTENTS
DESCRIPTION ......................................................................... 3
SAFETY : WARNINGS ............................................................. 3
DIMENSIONS ........................................................................... 4
SPECIFICATION ...................................................................... 5
Pressures ......................................................................... 5
Plumbing Connections ..................................................... 5
INSTALLATION ......................................................................... 6
Before You Begin ............................................................. 6
Install the Mixer ................................................................ 7
Installing the Drain ........................................................... 13
Install the Link for Drain ................................................... 14
Finish The Installation ...................................................... 16
USER MAINTENANCE ............................................................ 17
Cleaning ........................................................................... 17
Ceramic Valve Replacement ............................................ 18
SPARE PARTS ......................................................................... 19
NOTES ..................................................................................... 23
CUSTOMER SERVICE ............................................................ 24
Guarantee of Quality ........................................................ 24
1023012-W2-B
2

DESCRIPTION
The Memoirs Stately 3 Hole Basin Mixer is a mixer for basins with mixer
holes between 200mm and 410mm centres. It has either cross handles or
lever handles, and has a pop-up drain with a lift rod and tailpiece.
SAFETY : WARNINGS
Kohler products are precision-engineered and should give continued
superior and safe performance, provided:
1. They are installed, commissioned, operated and maintained in
accordance with the recommendations given in this Manual.
2. Periodic attention is given, as necessary, to maintain the product in
good functional order. Recommended guidelines are given in the
MAINTENANCE section.
Carefully inspect the new fixture for any signs of damage.
When installing Kohler Products, manufacturers guidelines for power tool
safety should be followed.
1023012-W2-B
3

DIMENSIONS
P3907010/1
410mm MAX.
200mm MIN.
44mm
MAX.
29mm DIA.
46mm
STATELY
CROSS
HANDLE
STATELY
DECO
HANDLE
48mm
64mm
87mm
STATELY
LEVER
HANDLE
48mm
62mm
89mm
48mm
17mm
14mm
24mm
32mm
114mm
81mm
102mm
Pop-Up Drain
1-1/4" O.DIA.
102mm
67mm
54mm
48mm
64mm
83mm
1023012-W2-B
4

SPECIFICATION
Pressures
The minimum recommended operating pressure is 0.5 bar.
For optimum performance, a minimum operating pressure of 1.0 bar is
recommended.
Plumbing Connections
Hot (H) and Cold (C) inlets must be connected to the correct inlet supplies.
1023012-W2-B
5

INSTALLATION
Before You Begin
1. Turn off the water supply.
2. The plumbing installation must comply with Water Supply
Regulations/Bye-laws (Scotland), Building Regulations or any
particular regulations and practices, specified by the local water
company or water undertakers. The installation should be carried out
by a plumber or contractor who is registered with, or is a member
of an association such as:
Institute of Plumbing (IOP), throughout the UK.
National Association of Plumbing, Heating and Mechanical Services
Contractors (NAPH & MSC), England and Wales.
Scottish and Northern Ireland Plumbing Employers’ Federation
(SNIPEF), Scotland and Northern Ireland.
3. Install the mixer before installing the basin.
4. Before installation carefully inspect the new fixture for any signs of
damage.
1023012-W2-B
6

Install the Mixer
P3907020
Apply Sealant
Metal Washer
Nut
1. Apply a ring of sealant to the underside of the spout in accordance
with the manufacturer’s instructions.
2. Fit the spout through the top of the basin.
3. Install the washer and the nut. Use a spanner to tighten the nut.
1023012-W2-B
7

P3907100
Concealing Plate
Fibre Washer
Locknut
4. Thread the locknuts half way down the valve bodies.
5. Slide the fibre washers over the valve bodies.
6. Insert the valve bodies into the mounting holes from the bottom of the
basin. Make sure that the valve body marked ‘COLD’ is installed in the
right hand hole (as viewed from the front of the basin).
7. Apply a ring of sealant to the underside of the concealing plate in
accordance with the manufacturer’s instructions.
8. Thread the concealing plate onto the valve body.
1023012-W2-B
8

P3907030
Valve Body
Skirt
9. Align the handle splines onto the valve splines and thread the handle
skirt onto the concealing plate.
10. Loosely secure the valve bodies into position with the locknuts, but do
not tighten.
1023012-W2-B
9

P3902160
Valve
Outlet
Body
VALVE ALIGNMENT
200mm (centre to centre)
VALVE ALIGNMENT
410mm (centre to centre)
Valve
Outlet
Body
Valve
Outlet
Body
Valve
Outlet
Body
Spout Spout
11. Position the valve bodies in their correct orientation, usually facing
towards the spout for maximum valve centres, and facing outwards
for minimum centres. Adjust the position to suit your installation.
Note! Make sure there is sufficient clearance to thread the water supply
hoses and water supply pipe coupling nuts onto the valve body outlets.
12. Close the valves using the mixer handles.
13. Temporarily remove the handles, and re-attach them onto the valve
splines so that the handles point away from the mixer spout when the
valves are in the closed position.
14. Attach the O-ring onto the concealing plate and re-thread the handle
skirt onto the concealing plate.
15. Use a spanner to tighten the valve locknuts.
16. Screw the hoses onto the valve bodies. Use a spanner to tighten the
nuts, but do not over tighten.
1023012-W2-B
10

P3907040/1
Flexible Hose
Plastic
Gasket
Supply Tee Threaded Bushing
Rubber
Washer
Rubber Washer
17. Remove and retain the guide tube nut and O-ring from the supply tee
sleeve.
18. Insert the plastic gasket and rubber washer into the tee. Screw the tee
onto the spout until hand tight.
19. Align the supply arms to the sides. Slip the O-ring over the guide tube,
and use a spanner to tighten the guide tube nut to the sleeve.
20. Hold the spout in position, and tighten the tee securely. Do not
overtighten.
21. Connect the hoses to the tee inlets and the valve bodies. Do not use
thread sealant. Avoid kinking the hoses. Do not over tighten.
1023012-W2-B
11

P3902190
Valve Body
Supply Hose
Water Supply
Inlet
Spanner
22. Connect the water supply hoses to the valve inlets. Do not use thread
sealant. Do not over tighten.
23. Connect the water supply hoses to the water supplies. Avoid kinking
the hoses. Do not use thread sealant. Do not over tighten.
1023012-W2-B
12

Installing the Drain
Flange
Gasket
Apply Silicone Sealant
Washer
Nut
Drain Body
Seal Hole
P3907115
Fixture
1. Remove the protective cover from the flange.
2. Apply sealant around the underside of the waste in accordance with
the manufacturer’s instructions.
3. Assemble the nut, flat washer and tapered gasket (tapered side up)
fully onto the body.
4. From the underside of the fixture, insert the drain body up into the drain
hole.
5. From the top of the fixture, securely hand tighten the flange onto the
drain body.
6. Make sure that the drain body seal is facing the back of the fixture and
securely tighten the nut.
7. Remove any excess sealant.
1023012-W2-B
13

Install the Link for Drain
P3923110
Thumb
Screw
Clip
Rod
Link
1. Slide the clip and the link onto the rod with the thumbscrew facing
towards the rear of the basin.
2. Move the link to the desired position by squeezing the clip and sliding
it along the rod.
3. Push the rod down (open position).
1023012-W2-B
14

P3907050
Link
Thumb
Screw
Lift Rod
Handle
4. Slide the lift rod through the hole in the spout and through the hole in
the link.
5. Tighten the thumbscrew on the link so that the lift rod knob is touching
the spout.
6. Install the basin in accordance with its instructions.
1023012-W2-B
15

Finish The Installation
P3907090
Aerator
1. Make sure that both of the tap handles are turned off (HOT= clockwise,
COLD = anti-clockwise).
2. Turn on the main water supply and check for leaks.
3. Remove the aerator from the spout. Turn on both hot and cold valves
and run water through the spout for one minute to remove any debris.
Check for leaks.
4. Turn off the hot and cold valves.
5. Re-install the aerator.
1023012-W2-B
16

USER MAINTENANCE
Cleaning
Caution! Risk of product damage. Many cleaners contain abrasive and
chemical substances, and should not be used for cleaning stainless steel,
enamel, plated or plastic fittings. These finishes should be cleaned using
a mild washing up detergent or soap solution, rinsed and then wiped dry
with a soft clean cloth.
1023012-W2-B
17

Ceramic Valve Replacement
P3902200
REMOVE INSTALL
Ceramic
Valve Unit
1. Turn off the water supply and relieve pressure through the tap.
2. Remove the lever assembly from the valve by unscrewing the handle
skirt.
3. Removetheexistingvalve.
4. Thread the new ceramic valve into the valve body until hand tight.
Caution! Risk of product damage. Make sure the ceramic cartridge
is not over tightened. This may damage the ceramic valve and result in
internal leakage.
5. Tighten the ceramic cartridge using a suitable spanner.
6. Replace the handle assembly as shown in the installation section of
this manual.
7. Turn on the water supply and check for leaks.
1023012-W2-B
18

SPARE PARTS
454W-3S 454W-4S
454W-4V
P3907080/1
1023012-W2-B
19

1000283**
Handle
1000282**
Handle
Stem
Concealing
Plate
78125
Spline Adapter
Trim Ring
Skirt
88490
Grub Screw
87536
Screw
88490
Grub Screw
Washer
O-Ring
P3907060/2
1025208**
Handle
Washer
Lock Nut
460.63 (pair)
1/2" Valve Assembly
86189
Hose
3005837
Hose
A
Fibre Washer (x 3)
** Variation and/or finish/colour code may be required when ordering.
1023012-W2-B
20