Kohler 99721T-4 User manual

1226010-2A-B 1
BEFORE YOU BEGIN
All information is based on the latest product information available at the time of publication. Kohler Co. reserves
the right to make changes in product characteristics, packaging, or availability at any time without notice.
Please leave these instructions for the consumer. They contain important information.
NOTES:
1. Flush the water supply pipes thoroughly to remove debris.
2. Inspect the supply tubing for damage and leakage. Replace and maintain as necessary.
3. Observe local plumbing codes. Shut off the main water supply.
4. Check for leaks before covering the pipes, repair as needed.
5. Please ensure only apply water pressure test on the product, and empty the air in pipe and faucet thoroughly
before the test. Please ensure test pressure below 0.8MPa(8bar) and test duration within 30 minutes.
STANDARD APPLICABLE
Special model meets or exceeds the following at date of manufacture: TIS
1226010-2A-B 4
INSTALLATION INSTRUCTIONS
99721T-4 99723T-4 99725T-4 Recessed Bath Shower Trim And Valve
99722T-4 99724T-4 99726T-4 Recessed Shower Only Trim And Valve
MODULO
99721T-4 99723T-4 99725T-4 Recessed Bath Shower Trim And Valve
99722T-4 99724T-4 99726T-4 Recessed Shower Only Trim And Valve
MODULO
ROUGH-IN DIMENSIONS
SERVICE PARTS
**Color code must be specified when ordering.
99722T-499721T-4
99723T-4 99724T-4
Ø180
14
68~98
65
91.7
The finished wall The finished wall
The finished wall The finished wall
180
15
66~96
65
85
140
14
68~98
Ø180
91.7
15
66~96
180
85
140
833730
99721T-4/99723T-4/
99725T-4:3015582**
871363
871363
3006991
3006991
3006930
3006930
870667
3016134
870667
3016134
99721T-4/99723T-4/
99725T-4:3007134
99722T-4/99724T-4/
99726T-4:3007136
3010602
3010602
99721T-4:1226005**
99722T-4:1226008**
3016037**(Only for CP)
1233958**(Except CP)
99721T-4/99722T-4:1223615**
99723T-4/99725T-4:1226013**
99724T-4/99726T-4:1226015**
99725T-4/99726T-4:1223611**
99725T-4/99726T-4:1223611**
833438
3008523
3006927**
3006927**
99723T-4/99724T-4:1223612**
99723T-4/99724T-4:1223612**

1226010-2A-B 2 1226010-2A-B 3
INSTALLATION CHECKOUT
CLEANING INSTRUCTIONS
All Finishes: Clean the finish with mild soap and warm water. Wipe entire surface completely dry with clean soft
cloth. Many cleaners may contain chemicals, such as ammonia, chlorine, toilet cleaner etc, which could adversely
affect the finish and are not recommended for cleaning.
Do not use abrasive cleaners or solvents on Kohler faucets and fittings.
INSTALLATION
NOTE: Install mounting box
kit(1) according to the rough-in
dimensions of 98699T-NA.
Cut the protrudent part of the
mounting box kit out of the
finished wall. Unscrew the
screw(2), remove the protect
cover kit(3).
Remove the protection(5) on the
valve kit(4). NOTE: Don’t drop the
o-rings(6). The holes on the bottom
of the valve kit should be aligned
with the holes in the mounting box.
Install the valve kit into the mounting
box kit, tighten the screws(7).
Slide the cover kit(8) onto the valve
with the plugs(9) facing outside
(NOTE: Don’t squeeze out the rings
10,11). Push it against the wall.
Secure it with the screws(12).
Slide the faceplate(13) onto the valve
with slots(14) downwards. Push it
against the wall.
Screw the bonnet(15) on the valve.
Install the handle(16) on the valve
stem. Tighten the screw(18) with hex
wrench(17). Press plug button(19) to
the hole.
The illustration shown is the correct position of the handle in the closed position.
Ensure that all coupling nuts are tight.
Ensure that the handle is in the off position.
Turn on the main water supply, and check for leaks. Repair as needed.
1
2
3
4
5
6
7
8
9
10
12
11
4
19
13
14
15
17 18
16
99721T-4 99722T-4
99725T-4 99726T-499723T-4 99724T-4
99725T-4 99726T-4
180
15
66~96
6580
140
The finished wall The finished wall
15
66~96
180
80
140