Kohler C3-130 User manual

Installation Guide
安装说明
静安
：
：
English page 2-8
中 文 页 码 9-15
Smart Seat
清舒宝智能便盖
C3-130
K-4107T-HC-0
1334325-T01-D

Thank You For Choosing Kohler Company
Thank you for choosing a Kohler product. Kohler craftsmanship offers you
a rare combination of proven performance and graceful sophistication that will
satisfy you for years to come. The dependability and beauty of your Kohler
product will surpass your highest expectations. We are very proud of our products
here at Kohler and we know you will be too.
Please take a few minutes to study this Homeowners Guide. Pay special attention
to the care and cleaning instructions.
All information in this manual is based upon the latest product information
available at the time of publication. At Kohler, we constantly strive to improve the
quality of our products. We reserve the right to make changes in product
characteristics, packaging or availability at any time without notice.
1334325-T01-D
2
Kohler Co.

□Warning: risk of electric shock, fire or personal injury. This product must be
installed safely. Connect only to dedicated 220V~, 50Hz, 10A circuit protected
by Ground-Fault Circuit-Interrupters (GFCI’s) or Earth-Leakage Circuit-Breakers
(ELCB’s)．
□Risk of electric shock or product damage. Do not immerse the product into water.
□ Risk of product damage. Do not plug in before completing all other installation steps.
□
Risk of product damage. Do not install at a place where it may be splashed by water.
□Observe all local plumbing and building codes.
□Do not use an extension cord with the product.
□Risk of product damage. Do not install the product at a place with excessive
humidity, where moisture may condense at the surface of the product. Please
maintain that the usage environment is under adequate ventilation, so as to
prevent damage to electronic components.
□Risk of product damage or property loss. Water leakage may happen if the water
pipe connector is pulled or pressed with excessive force.
□Risk of product damage. The product may be damaged if the nozzle is applied
with excessive force.
□Risk of product damage. Align threads when connecting water inlet, otherwise
the damaged thread might cause water leak.
□Min water pressure 0.07Mpa (dynamic pressure)
Max water pressure 0.74Mpa.
□Only connect to tap water.
□ Unplug and discharge water inside if the product is going to be idle for a long time.
□When install the product in the room, a stop valve shall be installed in a close
proximity. For emergency circumstances, the water inlet valve shall be stopped
without using any tools; otherwise unexpected failure may cause the loss to the
customer.
Note:
Warning:
Tape Rag
Tools and Materials
Adjustable Wrench Blade Screwdriver
Before You Begin
Kohler Co.
3
1334325-T01-D

1. Match toilet roughing-in requirements and installation tips
2. Install an Electrical Outlet
It is recommended to use water-resistant socket. Do not use an
extension cord with the product.
WARNING: Risk of electric shock, fire, or personal injury.
This product must be grounded. Connect only to a
dedicated 220V~, 50Hz ,10A circuit protected by Ground-Fault
Circuit-Interrupter (GFCI) or Earth-Leakage Circuit-Breaker (ELCB).
NOTE: Follow local codes when determining the electrical outlet location.
Route the electrical and install to a 220V~, 50Hz, 10A GFCI- or ELCB-
protected receptacle.
3. Preparation
Turn off the water supply to the toilet.
Flush the toilet to relieve any pressure from the water supply hoses.
Position a container under the fill valve to catch any excess water.
Disconnect the water supply hose from the toilet fill valve.
Remove the existing toilet seat.
1. Distance between installation holes: 136 - 210mm.
2. Distance between installation holes and tank front rim:>20mm.
3. Distance between installation holes and bowl inner rim:<70mm.
4. Distance between installation holes and tank top rim: 460 - 490mm.
5. Bowl inner diameter: 370 - 390mm.
6. The distance between the seat and the plug should be maximum 1 meter.
1334325-T01-D
4
Kohler Co.

4. Install the Mounting Plate
For All Other Installations:
Position the mounting plate over the toilet mounting holes.
Insert a bolt through the mounting plate and the toilet mounting holes.
Position the washers so they rest in the grooves of the mounting plate.
Thread a nut onto each of the bolts. Handtighten the nut.
For Toilets with Threaded Inserts:
Loosely thread the bolts into the inserts. Do not overtighten for further
adjustment.
NOTE: Select the appropriate mounting plate according to the instruction for
mounting distance on the mounting plate.
Place the mounting plate in the mounting hole above the toilet.
Screws should be inserted respectively into the washers.
NOTE: Some toilets come with threaded inserts pre-installed in the mounting
holes. For toilets with threaded inserts, the nut is not required.
Insert a bolt through the mounting plate and position the washers so they
rest in the grooves of the mounting plates. Please pay attention to washer
direction. The bending part of washer should be placed upwards.
Slide a washer onto each of the bolts. Please pay attention to washer
direction. The bending part of washer should be placed upwards.
Kohler Co.
5
1334325-T01-D

5. Install the Seat
For All Other Installations:
No need to remove the seat for seat position adjustment. Adjust the position
seat and mounting plate only by loosening nuts and tighten nuts when they
are adjusted to properly align with the seat.
Tilt toilet 15°-25°, align toilet cover with mounting board, snap in and release
toilet. The click sound indicates the installation completed.
To adjust the seat position, remove the seat and reposition the mounting
plate as needed.
Once the seat is positioned as desired, remove the seat and securely tighten
down the mounting plate.
Reinstall the seat.
NOTE: The mounting plate may need to be adjusted to properly align with the
seat.
For Toilets with Threaded Inserts:
1334325-T01-D
6
Kohler Co.

6. Connect the Water Supply
Connect the T-valve directly to the toilet fill valve.
NOTE! For those newly installed plumbing pipes, (before the inlet hose is
connected to the T-valve,) must flush for several seconds to clean the inner
side of the pipe in order to remove the dirt and debris, etc.
Connect the T-valve to the toilet seat with the supplied hose.
NOTE：Please use new hose enclosed with tools. Please do not reuse the
old hose.
Connect T-valve to water supply system (valve shall be purchased by
customer).
Turn on the water supply.
NOTE：Flush the water supply pipes thoroughly to remove debris. The
product is designed for tap water. Make sure not to use industrial water/grey
water/black water/sea water for the water supply.
Check all connections for leaks and make any adjustments as needed.
IMPORTANT! Risk of product damage. Take care to face right in position to
the inlet pipe thread and seat thread. Take care not to crossthread or overtighten
connections. Hand tighten plus one-quarter turn is sufficient for tightening.
IMPORTANT! Risk of product damage. Use care not to scratch the product
surfaces.
Supply Stop
T-Valve
Kohler Co.
7
1334325-T01-D

7. Installation Checkout
Toilet makes one short beep once it is plugged in. The nozzle
stretches out and draws back once. Backlight on the side keyboard
lights up and the night light flashes. All the actions last until the
initialization process completes.
Attach the clips evenly along the hose and power cord.
The seat is activated by skin-to-seat contact. Unless otherwise
stated, the seat must be occupied to activate the functions. To
activate the seat controls for testing purposes, when facing the toilet,
place your hand or a damp wash cloth on the right side of the seat
approximately 1/3 from the front of the seat (sensor area).
Proceed to the “Operation” section of the Homeowners Guide to test
the various seat functions.
Ensure if water inlet valve is OPEN.
Wrap the toilet seat with plastic wrap to prevent water from spraying
from the toilet during testing.
1334325-T01-D
8
Kohler Co.

谢谢您选择科勒公司
谢谢您选择科勒。科勒技术提供了可靠性能和优雅生活的结合，满足了
您未来几年的需求。科勒产品的美观和可靠性将满足您最挑剔的眼光。
我们为我们科勒的产品感到非常地自豪，相信您也会。
请花几分钟阅读一下这本用户手册，特别注意维护和清洗说明。
这本说明书中所有的信息基于最新公开的产品信息。在科勒，我们一贯
坚持改善我们产品的质量。我们保留在任何时候不通知的情况下改变产
品特性，包装或实用性的权利。
Kohler Co.
9
1334325-T01-D

安装之前
工具和材料
□触电，火灾或人身伤害的危险。本产品必须安全接地。只能连接到专
用的220V~, 50Hz, 10A带接地故障断路器或接地漏电保护器的电路中。
□触电或产品损伤的危险。不要把产品浸入水中。
□产品损伤的危险。在所有其他安装步骤结束之前不要插电源线插头。
□产品损伤的危险。不要把产品安装在水可能溅到的地方。
□ 遵守所有当地的管道和建筑标准。
□ 不要使用延长电线连接产品。
□产品损伤的危险。不要把产品安装在过分潮湿的地方，在这种地方，水
汽可能凝聚在产品表面。请始终保持使用环境有足够的通风，以防止电
子组件的损坏。
□产品损坏或财产损失的危险。硬推、硬拉水管接头可能造成水渗漏。
□产品损坏的危险。不要在喷嘴上施加过大的力，否则产品可能损坏。
□产品损坏的危险。连接本产品进水管时要小心对正螺蚊，否则会损坏产
品进水口螺纹，造成漏水。
□最小进水压力0.07Mpa（动压）
最大进水压力0.74Mpa。
□ 只能连接到自来水的水源。
□ 如果产品长时间不用，请拔下插头并排干本机里的水。
□ 在安装本产品的同一房间中，需要在触手可及的位置安装一个止水阀，
用于紧急情况下，无需借助工具即可切断本产品的进水水路；否则本
产品的意外故障可能会导致用户损失。
擦布
注意：
警告:
1334325-T01-D
10
Kohler Co.