Kohler K-15635 User manual

Installation Guide
Centerset Lavatory Faucet
K-15635, K-15636
Mproduct numbers are for Mexico (i.e. K-12345M)
Los números de productos seguidos de
Mcorresponden a México (Ej.
K-12345M)
Français, page “Français-1”
Español, página “Español-1”
1031177-2-B

Thank You For Choosing Kohler Company
We appreciate your commitment to Kohler quality. Please take a few
minutes to review this manual before you start installation. If you
encounter any installation or performance problems, please don’t
hesitate to contact us. Our phone numbers and website are listed on
the back cover. Thanks again for choosing Kohler Company.
Tools and Materials
Before You Begin
Observe all local plumbing and building codes.
Shut off the main water supply.
Carefully inspect the waste and supply tubing for any sign of
damage.
For new installations, install the faucet and drain to the lavatory
before installing the lavatory.
Kohler Co. reserves the right to make revisions in the design of
faucets without notice, as specified in the Price Book.
Plumbers
Putty Thread
Sealant Pliers Adjustable
Wrench
Pipe Sealant
1031177-2-B 2 Kohler Co.

1. Faucet Installation
Clean the lavatory surface to remove any grease, oil, or debris.
Apply a ring of plumbers putty or other sealant around the
underside edge of the faucet body according to the putty
manufacturer’s instructions.
Insert the faucet through the lavatory holes.
Check the faucet alignment.
Thread the nuts onto the faucet shank and securely hand-tighten.
Wipe away any excess sealant.
Apply plumbers
putty.
Shank
Nut
Kohler Co. 3 1031177-2-B

2. Pop-Up Drain Installation
Remove the protective cover from the flange.
Apply a ring of plumbers putty or other sealant to the underside
of the flange according to the putty manufacturer’s instructions.
Assemble the nut, flat washer, and tapered gasket (tapered side
up) fully onto the body.
From the underside of the fixture, insert the drain body up into
the drain hole.
From the top of the fixture, securely hand tighten the flange onto
the drain body.
Make sure the drain body seal hole is facing the back of the
fixture, and securely tighten the nut.
Remove any excess putty or sealant.
Apply plumbers putty.
Flange
Tapered Gasket
Flat Washer
Nut
Drain Body
Fixture
1031177-2-B 4 Kohler Co.

3. Complete Pop-Up Drain Installation
IMPORTANT! If the tailpiece has been removed, double check that
the plastic washer is installed inside the flange body or the drain
will leak.
Connect the P-trap to the tailpiece.
Press the seal into the lift rod hole on the body.
Insert the stopper into the flange.
For regular installations, insert the short end of the rod into the
lift rod hole and under the stopper rod. For vandal-resistant
installations, fit the rod through the hole in the stopper rod.
Hand tighten the rod nut.
Remove and adjust the stopper as needed so it lifts about 3/8″(1
cm) when opened. To adjust, rotate the threaded stopper rod in or
out as needed. Retighten the stopper nut.
Slide one end of the clip onto the rod. Slide the link onto the lift
rod with the thumbscrew facing the back of the fixture.
Squeeze the other end of the clip, aligning the hole with the rod.
Move the link to the proper position by squeezing the clip and
sliding it along the rod.
Insert the lift rod into the hole in the body and then into the hole
in the link.
Tighten the thumbscrew onto the link so the lift rod knob extends
1/2″(1.3 cm) above the lift rod hole.
Check for leaks.
Body
Clip
Stopper
Flange
Seal
Rod Nut
Tailpiece
Thumb
Screw
Stopper
Rod
Plastic
Washer
Link
Rod
Kohler Co. 5 1031177-2-B

4. Grid Drain Installation
If present, remove the protective plastic cap from the drain and
discard.
Remove the nut, washer, and gasket from the drain body.
Apply a bead of plumbers putty or other sealant around the
underside of the flange according to the sealant manufacturer’s
instructions.
For drains with metal stoppers (K-7124 and K-7127): Close the
drain and rotate the drain body until the logo is positioned
horizontally (as illustrated).
Insert the drain into the drain hole and press into place.
Slide the gasket (tapered side up) onto the drain body.
Side the washer over the threads on the drain body.
Thread the nut up the drain body until snug against the
underside of the lavatory. Use care not to rotate the drain while
tightening the nut.
Using a wrench, tighten the nut.
Remove any excess putty or sealant.
Connect the P-trap to the drain body.
Gasket
Washer
Flange
Drain Body
Nut
With the drain
closed, position
so the logo is
horizontal.
Metal Stoppers Only
1031177-2-B 6 Kohler Co.

5. Supply Connections
If the lavatory is not installed, install it at this time according to
the lavatory manufacturer’s instructions.
Allow enough space for penetration of supply tubes into the
supply stops. Cut the supply tubes if necessary.
Connect the supply hoses to the supply stops. (Left is hot - right
is cold).
Tighten all connections.
6. Installation Checkout
Connect the P-trap.
Make sure all connections are tight.
Remove the aerator by turning it counterclockwise.
Open the drain.
Turn on the main water supply and check for leaks. Make any
adjustments as needed.
Turn on the faucet and run water through the spout for about a
minute to remove any debris. Check for leaks.
Turn off the faucet. Make any adjustments as needed.
Rinse any debris from the aerator and reinstall.
Nut
Compression
Union
HOT
COLD
Spout
Aerator
Kohler Co. 7 1031177-2-B

Guide d’installation
Robinet de lavabo à petit entraxe
Outils et matériels
Merci d’avoir choisi la compagnie Kohler
Nous apprécions votre engagement envers la qualité Kohler. Veuillez
prendre s’il vous plaît quelques minutes pour lire ce manuel avant de
commencer l’installation. Ne pas hésiter à nous contacter en cas de
problème d’installation ou de performance. Nos numéros de téléphone
et notre adresse du site internet sont au verso. Merci encore d’avoir
choisi la compagnie Kohler.
Avant de commencer
Respecter tous les codes de plomberie et de bâtiment locaux.
Couper l’alimentation d’eau principale.
Vérifier avec soin si les tubes d’évacuation ou d’alimentation
d’eau sont endommagés.
Pour de nouvelles installations, installer le robinet et le drain au
lavabo avant d’installer celui-ci.
Kohler Co. se réserve le droit d’apporter toutes modifications au
design des robinets et ceci sans préavis, comme spécifié dans le
catalogue des prix.
Mastic
d'étanchéité Ruban
d'étanchéité
pour filets
Pinces Clé à
molette
Mastic de canalisation
Kohler Co. Français-1 1031177-2-B

1. Installation du robinet
Nettoyer la surface du lavabo pour éliminer toute graisse, huile
ou débris.
Appliquer du mastic d’étanchéité sur le dessous du rebord du
corps de robinet selon les instructions du fabricant.
Insérer le robinet à travers les orifices du lavabo.
Vérifier l’alignement du robinet.
Visser les écrous sur le manche du robinet et sécuriser à la main.
Essuyer tout excès de mastic.
Appliquer du
mastic de
plomberie.
Manche
Écrou
Kohler Co. Français-2 1031177-2-B

2. Installation du drain escamotable
Retirer la pellicule protectrice de la bride.
Appliquer un anneau de mastic d’étanchéité ou un produit
semblable sur le dessous de la bride selon les instructions du
fabricant du mastic.
Assembler l’écrou, la rondelle plate et la bague d’étanchéité
biseautée (biseau vers le haut) sur le corps.
Introduire le corps du drain dans l’appareil, insérer le corps du
drain dans l’orifice du drain.
Du dessus de l’appareil, serrer délicatement à la main la bride sur
le corps du drain.
S’assurer que l’orifice d’étanchéité du corps du drain fasse face à
l’appareil et serrer délicatement l’écrou.
Retirer tout excédent de mastic d’étanchéité.
Appliquer du mastic
de plomberie.
Bride
Joint d'étanchéité conique
Rondelle plate
Écrou
Corps du drain
Appareil sanitaire
1031177-2-B Français-3 Kohler Co.