Install The Faucet
To perform installation, installer must
provide G1/2˝ female supply fittings (1),
space 150mm apart, level and not
extend beyond finished wall surface.
Flush the water supply pipes thoroughly
to remove debris.
Install the two offset connectors (2) into
the HOT and COLD supply pipes. Use
appropriate thread sealants on pipe
threads. Adjust the center-to-center
distance between the connectors to
150mm and level. They should extend
40~45mm beyond the finished wall.
Thread the escutcheons (3) onto the
connectors so that the escutcheons
contact the finished wall.
Put washers (8) into supply nuts of the
faucet. Thread the faucet supply nuts (7)
onto the connectors and tighten.
NOTE: When tighten the nut, use strap
wrench or soft cloth between product
and regular wrench to protect the finish.
Put the check valve (11) into the hand-
spray(4) inlet. Put the restrictor (10) into
the handspray inlet if needed.
NOTE: Keep the O-ring of the check
valve outward.
Put the washer (6) between hose (5) and
shower outlet (9). Provide washer
between the hose and handspray.
Tighten all the connections.
การติดตั้ง INSTALLATION
2
3
17
16
การติดตั้งกอกนํ้า
1
2
Cold
Hot
150 mm/
ขอสังเกต
ทดสอบการติดตั้ง
กอกผสมลงอางอาบนํ้าและยืนอาบ
แบบติดผนังพรอมฝกบัวสายออน
ขอสังเกต:
กอกผสมยืนอาบแบบติดผนัง
พรอมฝกบัวสายออน
4
5
6
7
8
2
9
4
11
10
ขอสังเกต:
837363-X2-E 2
837363-X2-E 3
CARE AND CLEANING
การดูแลรักษาและทําความสะอาด
วิธีการติดตั้งขอแขวนฝกบัว How to Install the Shower
Bracket
Determine a suitable location on the
finished wall to install the bracket. Mark
bracket base mounting hole locations
on the wall according to the dimension.
Drill two holes on the finished wall, the
holes should match the anchors(12).
Install the anchors.
Tighten screws(13) to secure bracket
base(14, flat side upward). Put the
bracket(15) onto the bracket base and
lock by stopper.
27
13
15
14
12
For best results, keep the following in mind when
caring for your product:
•Always test your cleaning solution on an
inconspicuous area before applying to the entire
surface.
•Wipe surfaces clean and rinse completely with
water immediately after applying cleaner. Rinse
and dry any overspray that lands on nearby
surfaces.
•Do not allow cleaners to soak on surfaces.
•Use a soft, dampened sponge or cloth. Never
use an abrasive material such as a brush or
scouring pad to clean surfaces.
• The ideal cleaning technique is to rinse
thoroughly and blot dry any water from the
surface after each use.
•
•
•
•
•
INSTALLATION CHECKOUT
Ensure that all coupling nuts are tight.
Ensure that the handle is in the off
position.
Turn on the main water supply, and
check for leaks. Repair as needed.
Bath & Shower Faucet:
Remove the handspray and remove the
aerator (16) by key (17). Run hot and
cold water through the faucet for about
a minute to remove any debris. Check
for leaks. Remove any debris from the
aerator assembly. Shut the faucet off,
and reinstall the aerator assembly and
handspray.
NOTE: The minimum inlet water
pressure for the diverter is 0.05MPa
(0.5bar).
Shower Faucet:
Remove the handspray. Run hot and
cold water through the faucet for about
one minute to remove any debris.
Check for leaks. Shut the faucet off,
and reinstall the handspray.
Replace bracket cover onto bracket
base. Hang the handspray on the shower
bracket.