Kohler MODULO 99960T-4V User manual

1228791-2A-A 1
BEFORE YOU BEGIN
All information is based on the latest product information available at the time of publication. Kohler Co. reserves
the right to make changes in product characteristics, packaging, or availability at any time without notice.
Please leave these instructions for the consumer. They contain important information.
NOTES:
1. Flush the water supply pipes thoroughly to remove debris.
2. Inspect the supply tubing for damage and leakage. Replace and maintain as necessary.
3. Observe local plumbing codes. Shut off the main water supply.
4. Check for leaks before covering the pipes, repair as needed.
5. Please ensure only apply water pressure test on the product, and empty the air in pipe and faucet thoroughly
before the test. Please ensure test pressure below 0.8MPa(8bar) and test duration within 30 minutes.
1228791-2A-A 4
INSTALLATION INSTRUCTIONS
99960T-4V 99962T-4 99964T-4A Recessed Bath Shower Trim And Valve
99961T-4V 99963T-4 99965T-4A Recessed Shower Only Trim And Valve
99960T-4V 99962T-4 99964T-4A Recessed Bath Shower Trim And Valve
99961T-4V 99963T-4 99965T-4A Recessed Shower Only Trim And Valve
MODULOMODULO
ROUGH-IN DIMENSIONS
SERVICE PARTS
**Color code must be specified when ordering.
180
17
84~114
65
81
17
87~117
65
70
140
180
140
180
140
180
140
99961T-4V99960T-4V
99962T-4 99963T-4
81
17
87~117
70
17
84~114
833730
99960T/99962T/99964T:1228789**
99961T/99963T/99965T:1228790**
3006927**
99960T/99961T:1233962**
833438
1032012**
99962T/99963T:1233963**
99964T/99965T:1233961**
36449
1031751**
42160
1030996**
99960T/99962T/
99964T:3015582**
871363
871363
3006991
3006991
3006930
3006930
870667
3016134
870667
3016134
99960T/99962T/
99964T:3007134
99961T/99963T/
99965T:3007136
3010602
3010602
The finished wall The finished wall
The finished wall
The finished wall

1228791-2A-A 2 1228791-2A-A 3
INSTALLATION CHECKOUT
CLEANING INSTRUCTIONS
All Finishes: Clean the finish with mild soap and warm water. Wipe entire surface completely dry with clean soft
cloth. Many cleaners may contain chemicals, such as ammonia, chlorine, toilet cleaner etc, which could adversely
affect the finish and are not recommended for cleaning.
Do not use abrasive cleaners or solvents on Kohler faucets and fittings.
INSTALLATION
NOTE: Install mounting box
kit(1) according to the rough-in
dimensions of 98699T-NA.
Cut the protrudent part of the
mounting box kit out of the
finished wall. Unscrew the
screw(2), remove the protect
cover kit(3).
Remove the protection(5) on the
valve kit(4). NOTE: Don’t drop the
o-rings(6). The holes on the bottom
of the valve kit should be aligned
with the holes in the mounting box.
Install the valve kit into the mounting
box kit, tighten the screws(7).
Slide the cover kit(8) onto the valve
with the plugs(9) facing outside
(NOTE: Don’t squeeze out the rings
10,11). Push it against the wall.
Secure it with the screws(12).
Slide the faceplate(13) onto the valve
with slots(14) downwards. Push it
against the wall.
Screw the bonnet(15) on the valve.
Install the handle(16) on the valve
stem. Tighten the screw(18) with hex
wrench(17). Press plug button(19) to
the hole.
The illustration shown is the correct position of the handle in the closed position.
Ensure that all coupling nuts are tight.
Ensure that the handle is in the off position.
Turn on the main water supply, and check for leaks. Repair as needed.
1
2
3
4
5
6
7
8
9
10
12
11
4
The finished wall The finished wall
99964T-4A 99965T-4A
180
17
83~113
65
70
140
180
17
83~113
70
140
13
14
15
16
1819
17
99961T-4V99960T-4V 99962T-4 99963T-4
99964T-4A 99965T-4A