Kohler K-19896 Operation manual

1102602-A2-A
Installation & User Guide
Dual-Flush Toilet
K-3735 K-3736
K-19896 K-4346

1102602-A2-A 2 Kohler Co.
Thank You For Choosing Kohler Company
We appreciate your commitment to Kohler quality. Please take a few
minutes to review this manual before you start installation. If you
encounter any installation or performance problems, please don’t hesitate
to contact us. Our phone numbers are listed on the back cover. Thanks
again for choosing Kohler Company.
Observe all local plumbing and building codes.
Carefully inspect the new toilet for damage.
If the existing toilet does not have a supply shut-off valve below the
cistern, install one before installing the new toilet.
Before You Begin
Tools and Materials
CAUTION: Risk of personal injury or product damage. Handle
with care. Vitreous china can break or chip if the product is handled
carelessly.

Kohler Co. 3 1102602-A2-A
1 Remove the existing toilet: Turn off the water supply and flush the toilet, then
sponge out all remaining water from the cistern. Disconnect the supply shut-off
valve (if present), and remove the old pan and cistern.
CAUTION: Risk of hazardous gases. If the new toilet is not installed immediately,
temporarity stuff a rag in the closet flange.
Installation
2 Define the position of connector: Place the connector onto the pan, position between
outlet and waste pipe.
3 Position the template on the floor to ensure the rear pan against the wall. Mark the
mounting hole centerline on the floor.
Connector to Wall Connector to Floor
Case 1 Case 2
Finished
Wall
Finished
Wall
Connector
Connector
Waste Pipe Waste Pipe
min. 90 mm.
max. 150 mm.
180 mm.
For this model, there are two types of connector. You can choose one
of the above pictures which is most suitable to your local plumbing
and building codes.

1102602-A2-A 4 Kohler Co.
Installation
4 Drill 3/8” (10 mm) mounting hole
between the mark locations on the
floor and insert the anchor.
5 Install the washer and insert the hexagon
screw into the bracket then tighten the
screw.
Anchor
Hexagon
Lag Screw
Bracket
Washer
Anchor
6 Install the sleeves,
tighten the screw
and attach the
caps.
7 Position the cistern on the pan by centering the gasget
on the pan inlet. Assemble the retaining washer and
sealing washer to the screw. Securely tighten the
screws so the cistern is level.
Screw
Sleeve
Hole
Cap
Gasket
Screw
Retaining
Washer Plan
Washer
Fiber
Washer
Sealing
Washer
Screw

Kohler Co. 5 1102602-A2-A
Installation
8 Connect the supply shut-off valve to the supply hose and connect supply hose to
toilet supply shank.
9 In cistern.
Water
Supply
Hose
Water
Supply
Hose
Rear Inlet TypeBottom Inlet Type
Rear Water Inlet
K-19896
Rear Water Inlet
K-3735, K-4346
Bottom Water Inlet
K-3736
Bottom Water Inlet
Optional 148794A-NA
Stop Valve
Tank Hose

1102602-A2-A 6 Kohler Co.
Install the Push Buttons
1 Remove the tape and protective pad. 2 Press down on the large button.
3 Pull out and remove the small button. 4 Pull out and remove the large button.
5 Press the large button on to the black
rod.
6 Press the small button on to the green
rod.
Black Rod
Large Button
Green Rod
Small Button
7 Insert the rod into the holes in the push
button housing.
8 Press down on the push buttons until
they click into place.
Tank Cover
protective pad.

Kohler Co. 7 1102602-A2-A
Install Flush Valve
1 Release flush valve by turn right and pull straight up on the canister.
2 Assembly flush valve by push straight down into the canister and turn left.
1
2
1
2

New Zealand
Kohler New Zealand Ltd.
Phone: [phone] Fax: [phone]
Australia
Kohler Co.
Phone: [phone] Fax: [phone]
©
2008 Kohler Co.
1102602-A2-A