Kohler KUMIN 18655T-CP User manual

18655T-CP
18656T-CP
18656T-S3-CP
18656T-S5-CP
18657T-CP
18658T-CP
18658T-S3-CP
18658T-S5-CP
安装之前
1
所有的资料是按最新出版的产品资料编写而成。
科勒公司保留任何时候不经通知即可改变产品特
性、包装或产品可供类型的权利。
说明书包括重要的安装、保养及清洁方面的内容，
请把这些资料交给用户阅读。
注意事项:
1. 一定要先彻底冲洗供水管以清除管道中的杂质,
使用水源为自来水或可供饮用水。
2. 请勿将强力及冲击施于产品，以免造成故障，
引起漏水。
3. 安装、清洁龙头时，切勿损伤感应窗口表面，
以免造成故障。
4. 如果是安装新的洗面盆，可将水龙头和排水组
件先安装好到面盆上。
5. 对于直流龙头，安装时注意电池的正负极不能
装反，电池盒盖要拧紧，防止电池受潮。
6. 对于交流龙头，安装时务必按照说明书的要求
正确连接导线，龙头安装完毕后才可向电源盒供
电。
7. 一个交流电源盒最多可供两个感应龙头。
8. 交流电的总电源必须有合适熔断丝加以保护。
9. 请勿使产品感应窗口靠近强紫外线或电磁场。
All information is based on the latest product information
available at the time of publication, Kohler Co. reserves the
right to make changes to product characteristics, packaging,
or availability at any time without notice. Please deliver these
instructions for the consumer. They contain important
installation, maintenance and cleaning information.
NOTES:
1. Flush the water supply pipes thoroughly to remove debris.
Faucet is designed for tap water or potable water.
2. Handle the faucet with care to avoid damaged.
3. Do not damage the surface of sensing window when
installing or cleaning the faucet.
4. For new installations, install the faucet and drain to the
lavatory before installing the lavatory.
5. As for DC type faucets, please pay special attention to
insert direction matches battery poles. Tighten the battery
cover completely to prevent its exposure to moisture.
6. For electric connection on AC faucets, carefully follow the
installation instructions provided. Only provide to the electric
power box after the installation is conpleted.
7. Only install a maximum of two faucets to one AC/DC
transformer.
8. Ensure electrical source is fitted with a suitable fuse to
protect AC/DC transformer unit from damage.
9. Do not put the faucet near strong ultraviolet or
electromagnetic field.
珂美
KUMIN
Kumin Sensor Faucet
珂美台盆感应龙头-交流电（单冷型不含电源盒）
珂美台盆感应龙头-直流电（单冷型）
珂美台盆感应龙头-直流电（单冷型 0.35GPM）
珂美台盆感应龙头-直流电（单冷型 0.26GPM）
珂美台盆感应龙头-交流电（冷热混合型不含电源盒）
珂美台盆感应龙头-直流电（冷热混合型）
珂美台盆感应龙头-直流电（冷热混合型 0.35GPM）
珂美台盆感应龙头-直流电（冷热混合型 0.26GPM）
BEFORE YOU BEGIN
1267716-T01-C
科勒（中国）投资有限公司
中国上海市闸北区江场三路158号邮编：200436
制造商：上海科勒电子科技有限公司
中国上海市宝山区丰翔路1955号邮编:200444

2 1267716-T01-C
使用说明
1. 手伸到出水口下方感应范围
内（感应距离随面盆、周围的情
况而自动调节），水龙头出水。
手离，0.5～1秒，水龙头自动止
水。
2. 冷热混水龙头水温调节：先
关闭热水角阀，再将冷水角阀旋
至冷水最大状态，再缓慢打开热
水角阀，以免烫伤。如冷水水压
大，打开全部热水角阀后，仍无
合适水温，请再缓慢减少冷水出
水量，直至水温使用舒适。
建议搭配脸盆
K-2297 凯瑟琳台下脸盆
K-2215T-M拉蒂纳台下脸盆
K-2949T 拂朗台下脸盆
K-2319 贝卡夫台下盆
K-2211T 卡斯登台下脸盆
K-2940T 温蒂斯台下脸盆
K-99184T 乔司 21''椭圆形台下盆
K-2883 维克圆形台下脸盆
K-2768T-1 皓台下盆
K-18572T-1 瑞琦一体化盆
K-18571T-1 瑞琦一体化盆
K-2264T 苔丝修边式台上盆
K-2749T 拂朗长方形一体化台盆
K-11479-VC1 拂朗半嵌入式脸盆
OPERATING INSTRUCTIONS
1. Place your hands under the faucet within the
sensor range ( the sensor range will auto-adjust
to its surroundings , the faucet should be on.)
The faucet will automatically turn off after 0.5~1
second after moving your hands away from the
sensor. The sensing distance will be adjusted
automatically per the condition of the lavatory
and surrounding environment.
2. Adjust the water temp for faucet with
temperature mixture: turn off hot water valve
first, and then turn on the water and adjust to full
cold, slowly turn on hot water valve to avoid
scalding. If cold water pressure is high and
unable to gain proper comfortable water temp
even hot water valve is fully open, turn down
cold water capacity slowly until water temp is
comfortable for use.
MATCHING LAVATORY RECOMMENDATIONS
K-2297 Kathryn®Undercounter Lavatory
K-2215T-M Ladena®Undercounter Lavatory
K-2949T Forefront™ Undercounter Lavatory
K-2319 Bancroft®Undercounter Lavatory
K-2211T Caxton®Undercounter Lavatory
K-2940T Vintage®Undercounter Lavatory
K-99184T Chalice™ Undercounter Lavatory
K-2883 Verticyl®Round Undercounter Lavatory
K-2768T-1 Karess Undercounter Lavatory
K-18572T-1 Reach™ Vanity Top
K-18571T-1 Reach™ Vanity Top
K-2264T Centerpiece™ Self-rimming Lavatory
K-2749T Forefront™ Vanity Top
K-11479-VC1 Forefront™ Semi-Recessed Lavatory
10. 为保证龙头正常工作，请务必安装连接组件。
11. 对于冷热混水龙头，先将连接热水的角阀关
闭，以免烫伤。
12. 修理面盆时，用黑色电工胶布粘住感应窗口。
13. 维修交流龙头时，必须断开交流电源并关闭
水源。
10.To ensure faucet proper operation, please install
connectors.
11.For faucet with temperature mixer, please turn off valve
before connecting to hot water to avoid scalding.
12.Cover the sensing window with black tape when repairing
lavatories.
13.Turn off the electrical source and shut down water
supply before servicing faucet.

128
101
128
101
建议搭配脸盆（续）
K-15095T-1-0 艾贝一体化盆
K-15096T-1-0 艾贝一体化盆
K-12629T-1-0 艾思格尔修边式台盆
K-2075T-1 史瑞夫台上脸盆
注意：
如果使用非推荐的脸盆，可能会产生溅
水在脸盆外面等情况。
安装尺寸(毫米)
18658T-CP
珂美台盆感应龙头-直流电（冷热混合型）
18658T-S3-CP
珂美台盆感应龙头-直流电（冷热混合型 0.35GPM）
RECOMMENDATION OF MATCHING
LAVATORY(Continued)
K-15095T-1-0 Urbanity™ Vanity Top
K-15096T-1-0 Urbanity™ Vanity Top
K-12629T-1-0 Escale®Self-rimming Lavatory
K-2075T-1 Serif®Self-rimming Lavatory
NOTE:
Use of a non-recommended lavatory may result in
water spillage outside of the lavatory.
ROUGH-IN DIMENSIONS（mm）
18656T-CP
珂美台盆感应龙头-直流电（单冷型）
18656T-S3-CP
珂美台盆感应龙头-直流电（单冷型 0.35GPM）
1267716-T01-C 3
18658T-S5-CP
珂美台盆感应龙头-直流电（冷热混合型 0.26GPM）18656T-S5-CP 珂美台盆感应龙头-直流电（单冷型 0.26GPM）
128
101 128
101

72
226
Drain
排水组件
φ54
φ41.2
φ66.5
φ31.75
AC/DC Transformer
(Not contained in 18655T-CP,18657T-CP, need purchasing )
交流电源盒
54
Output: DC6V
输出:
直流电压6V
Input: AC220V
输入:
交流电压220V
安装尺寸(毫米)(续） ROUGH-IN DIMENSIONS(mm)
(Continued)
AC/DC Transformer
交流电源盒 AC/DC Transformer
交流电源盒
18657T-CP
珂美台盆感应龙头-交流电（冷热混合型不含电源盒） 18655T-CP
珂美台盆感应龙头-交流电（单冷型不含电源盒）
128
101 128
101
4 1267716-T01-C

技术参数
电源：直流 4节5号碱性电池(LR06×4)
交流 电压220V,频率50/60Hz
检测时间：小于0.5秒
关阀延时：0.5～1秒
感应距离：自动调节
流量：水压为0.3MPa 时，流量不大于2.0L/min
超时用水控制：超时用水1分钟，自动止水。
环境温度：1～55 ℃
进水温度：0.5～71 ℃
适用水压：0.05～0.86MPa
安装步骤
如何安装水龙头
一龙头与面盆的安装固定
将固定螺杆(2)安装到水龙头(1)底部
处。再把垫片(3)套在固定螺杆上。并
嵌入水龙头底部的盘槽中。然后将电
源线(7)和进水软管(8)穿过安装孔，从
面盆下方将固定橡胶垫片(4)固定金属
垫片(5)和固定螺母(6)对齐固定螺杆向
上套入。调整水龙头电源线及进水软
管的位置。用扳手拧紧固定螺母以便
把水龙头固定在面盆上。
二安装控制组件
拧下控制盒盖(10)螺钉(11)，打开控制
盒(9)，根据安装尺寸图（图一）在墙
壁合适的位置钻孔，打入膨胀管
(12)，使控制盒紧贴墙面，再用螺钉
(13)将其固定在墙壁上。
注意：控制盒长边端需竖直放置，出
水口位置可根据需要左右调整。
将软管(16)一端与三通进水软管组件
(17)连接，另一端与控制组件(15)进水
口连接，再将出水口与龙头出水软管
(8)连接，三通进水软管组件另外两端
与角阀(18)连接。
对于单冷龙头，将软管一端与滤网接头
(19)相连，另一端与角阀连接即可。
9
11
10
图一
13
12
2
4
6
7
1
3
5
8
TECHNICAL SPECIFICATION
Power: DC 4 pieces of AA size alkaline batteries
AC 220V, 50/60Hz
Senser Duration: Less than 0.5s
Shut-off Delay: 0.5~1s
Sensing Distance: Automatic adjustment
Flow Rate: No more than 2.0L/min at 0.3MPa.
Overtime Flowing Control: Automatically stop flushing when
the faucet senses an object for more than 1 minute
continuously
Ambient Temperature: 1~55℃
Supply Water Temperature: 0.5~71℃
Supply Water Pressure: 0.05~0.86MPa
INSTALLATION
How to Install the Faucet
1.Secure faucet on lavatory
Install the stud (2) to the underside of the
faucet (1). Slide the gasket (3) over the
stud, and then seat the gasket in the groove
on the underside of the sprout. Cross power
cord (7) and water inlet hose (8) through
mounting hole, slide rubber washer (4),
metal washer (5) and nut (6) onto the stud
from under the sink. Adjust faucet power
cord and water inlet hose position, fasten nut
to secure faucet on lavatory mounting
surface by wrench.
2. Install Control Assy
Unscrew valve cover screw (11) with a
screwdriver and open valve cover (10).
Determine proper mounting location per
rough –in (Fig 1), then punch expansion
tube (12) in. Place valve box against the
wall and then secure control valve
assembly on the wall by bolts (13).
Note: Place the long end of control box
upright, water outlet position shall be
adjusted left/right based on requirements.
Connect hose (16) to Tee water inlet
hose assembly(17), and then connect
water outlet with faucet water outlet
hose (8). Connect Tee water inlet
hose other two ends with valve (18).
For cold water faucet, connect hose
to the cylinder(19) and then connect
with valve.
1267716-T01-C 5

17
6 1267716-T01-C
(20)
三安装电池组件
1.
(21)
4节5
注意：
2.
Apply plumbers putty
22
23
(25) (26)
25mm 55mm
adjust drain body position, otherwise
putty seal might be damaged.
Connect the tailpiece(25) to the
trap(26).The tailpiece should extend
25mmto 55mm into the trap.
Note:
1.Do not cofuse waterinlet with water outlet.
2.Ensure screen (18) andcylinder(19)install
on water inlet.
3.Ensure washer is in place (17) on on water
outlethose.
4.For 18656T-S5-CP、18658T-S5-CP must
be connect adapter assembly
16
15
18
混水(Mixer): 18657T-CP 18658T-CP ,
18658T-S3-CP 、18658T-S5-CP
14
Install battery assembly
1. Take battery box out, loose nscrews
(20), insert 4AA batteries per +/-
pole indication (21) on battery
box cover. Fasten battery box
cover with screws.
Note: no reversed battery
polarity. Do not mix new and used
batteries together.
2. Connect power cords with
corresponding color wires, then place
battery box assembly to empty space
within control assembly then fasten
control box by screws based on
installation direction. For AC faucet,
except corresponding cords connect to
AC/DC transformer output, other
installation methods are identical.
4How to Install the Drain
Unscrew the drain flange (22) from
drain assembly. Apply plumbers
putty around the bottom circle. Insert
drain body (23) into lavatory from the
underside.
Screw the drain flange (22) into drain
body (23). Tighten the locknut (24)
manually from the underside.
Note: Remove excessive putty. Note:
after tighten ing locknut (24), do not
四如何安装排水组件
(22）
(23)
(22)
(23)
(24)
(24)
注意：
仅用于（only for):18658T-S3-CP 、
18658T-S5-CP
19
单冷(Cold): 18655T-CP 18656T-CP ,
18656T-S3-CP 、18656T-S5-CP
20
21
注意：
1
2
3。
对于18656T-S5-CP、18658T-
S5-CP须在控制组件（15）出水口
节流器接头组件（14）。

AC/DC transformer
交流电源盒
Switch
开关
接220V交流电
Connect AC 220V
Wire Tube
穿线管
如何安装交流电源盒
(仅限于交流感应龙头)
Connect to
electrical Source
接交流电源
Connect to
Faucet
接感应龙头
Connect to
electrical Source
接交流电源
Connect to
Faucet
接感应龙头
AC/DC transformer
交流电源盒 接220V交流电
Connect AC 220V
Faucet
感应龙头 Faucet 感应龙头
Switch
开关 Wire Tube
穿线管
HOW TO INSTALL THE AC/DC
TRANSFORMER (FOR AC
TOUCHLESS FAUCET ONLY)
一个交流电源盒供一个感应龙头
One AC/DC transformer supply one touchless faucet
Faucet
感应龙头
一个交流电源盒供两个感应龙头
One AC/DC transformer supply two touchless faucets
注意：禁止将交流AC220V接入直流DC接线端。
Note: Do not connect AC 220V electrical source directly to DC connector.
注：18655T-CP、18657T-CP交流电源盒需另购。 Not contained in 18655T-CP、18657T-CP, need purchasing
1267716-T01-C 7

用户自备角阀 外螺纹
如何转换成混水感应龙头
若用户另购三通进水软管组
件）
( )
0.5mm2
0.3mm2
1.
2.
Then connect AC connector to AC connector within
FPC pipe, DC connect or (black-orange) onelectrical
boxto faucetpower cordconnector (wirefromvalve
box). FinallyturnonAC power source.Faucet will
commence auto-sense mode which will take 2minutes.
The faucet will notwork duringthis period.
( )
AC 2分钟
AC
DC
三通进水软管组件
Tee , Inlet Assy
HOW TO CHANGE TO AMIXING SENSOR
FAUCET (If customerpurchases tee inlet
8 1267716-T01-C
1.AC power unit (sticker on the back) should be
installed in adry place away from water. Customer
should prepare wire tube and wire according to their
requirement. Wire tube should be mounted into the
wall. Suggested wire: AC connection wire adopts wires
with protecting layer or sleeve and the section should
be ≥0.5mm2.The section of DC connection wire
should be ≥0.3mm2.The connection pattern must
follow the illustrations above.
2.After wirelayout finished,check and repairif needed.

如何转换成恒温阀感应龙头
(若用户另购恒温阀16294T-3-CP,
具体安装详见其说明书)
墙面
Wall
恒温阀
thermostatic valve
角阀
Stop Valve 角阀 Stop Valve
三通
Tee
三通
Tee
出水口
Outlet 三通
Tee
进热水
hot
进冷水
cold
墙面
Wall
注：三通、角阀请用户自备。
安装结果检查
检查并确保所有衔接处都已拧紧，打开排水系统
和主要供水源，检查并修理有漏水的接口。
清理说明
适用于所有加工处理过的表面，以中性肥皂水清
洗镀层表面，再以干净的软布彻底擦干整个表
面。许多清洁剂，比如氨水，去污粉及洁厕灵
等，会对电镀表面造成伤害，切忌使用。
有腐蚀性的清洁剂或溶剂不可使用于科勒的水龙
头及其配件上。
HOW TO CHANGE TO A THERMOSTATIC
SENSOR FAUCET (If users purchased the
thermostatic valve 16294T-3-CP, please refer to
the installation guide 16294T-3-CP)
接感应龙头
Connect Sensor Faucet
MIN 50mm
Note: Please prepare the tee and stop valve accordingly.
INSTALLATION CHECKLIST
Check and ensure that all connections are tight. Open the
drain. Turn on main water supply and check for leaks.
Repair leakage when necessary.
CLEANING INSTRUCTIONS
Applicable for all finishes: clean the finish with amild soap.
Wipe entire surface completely dry with aclean soft cloth.
Most cleaners may contain chemicals, such as ammonia,
chlorine, toilet cleaner etc. which could adversely affect the
finish and are not recommended for cleaning. Do not use
abrasive cleaners or solvents on Kohler faucets and
fittings.
用户须知
1. 感应指示灯的各种闪烁情况
感应指示灯是使用者了解感应龙头有效、唯一
的途径。所以明白了感应指示灯闪烁所代表的
含义，可以正确使用感应龙头，
1267716-T01-C
IMPORTANT CONSUMER INFORMATION
1. Light indicator Key
The indicator is the only and effective way to learn the
faucets working conditions. So the users can use the
sensor faucet correctly with knowing the meaning of the
sensor indicator's flashing.
9

连续在感应状态下使用约一分钟，龙头自动止水。
自动止水后，手或物体离开感应范围后，再次进
入感应范围内，龙头正常工作，否则无反应。
3. 清洗过滤系统
该感应龙头的控制组件内已包含了过
滤装置。如管内杂质过多或水质较
差，长期使用会引起出水情况不良。
请按以下步骤清洗过滤装置：
装入。
When the faucet flows continuously for 1minute, the
faucet will automatically stop.Objects must be removed
from the sensing range. Then the water will flow when
objects re-enter into the sensing range again. Otherwise,
the faucet will not work.
1. 关闭角阀。
2. 将控制组件进水口处软管拧下，取
出滤网组件，用水冲洗完毕后，重新
IMPORTANT CONSUMER INFORMATION
(Continued)
As shown:
(1) Quick flashing means the faucet is in the
period of adjusting sensing distance after power
on for 2 minutes. During these 2 minutes, please
do not disturb auto adjustment or place objects
within the sensing range.(2) The indicator flashes
every 6 seconds (DC type) indicates that the unit is
out of battery and has stopped working. Replease
指示灯 batteries.
Indicator Light (3) The indicator flashes every 2s: as for DC type
faucets, this indicates the unit is out of battery and
ceases working. Please replace batteries. For AC
faucet, it indicates two possibilities: one is that the
unit is out of battery; or poor DC terminal contact
under normal AC power supply.
(4) Under normal condition, the water will flow and
the indicator will flash once when objects are
detected. (The indicator does not flash when
faucet stops flowing.)
2. Timeout setting
1. Turn off stop valve.
2. Pull hose from control assembly water inlet,
take filter screen assembly out. Reinstall screen
after clean by water.
用户须知（续）
如图示:
(1) 快速闪烁，代表感应龙头正处于通电后
的两分钟自动调节阶段。期间，安装者、使
用者不得干扰其自动调节，感应范围内不要
放置物体。
(2) 间隔6秒钟闪烁一次（直流版本），表
示电池即将使用完，请更换电池。
(3) 间隔2秒钟连续闪烁：若直流感应龙头,
代表龙头电池耗尽，已停止工作，等待使
用者更换电池;若交流感应龙头，表示为两
种情况：一种为刚刚停电；另一种为在交
流供电正常的情况下，则电源盒直流接线
端接触不良。
(4) 在正常工作情况下，当有物体被感应
时，龙 头出水，感应指示灯闪烁一次。
(龙头关闭，感应指示灯不闪烁）
2. 超时出水控制
3.Clean the Filtration System
The touchless faucet control assembly include
filtration device. Poor water outflow shall be
滤网组件 caused by excessive impurities inside the hose
or poor water quality after long time use. Please
clean filtration device per following steps:
混水(Mixer): 18657T-CP 18658T-CP ,
18658T-S3-CP、18658T-S5-CP
滤网组件
单冷(Cold): 18655T-CP 18656T-CP ,
18656T-S3-CP、18656T-S5-CP
10 1267716-T01-C