Kohler Rada Intelligent Care MX1 20 User manual

11367863-W2-E
Please leave these instructions with the user
Installation Guide
Intelligent Care
MX1 Basin Mounted Tap

2
1367863-W2-E
General
Shut o󰀨 the main water and electrical supply.
Observe all local plumbing and building codes.
The Rada MX1 is a type 1, electronic, electrically operated, independently mounted valve. It is
intended for surface mounting and is for connection to the mains water supply.
Inlet Unit. Comprising of Filter / Flow Regulator / Check valve / Isolation is an integral component
of the tap, failing to install will invalidate the product’s warranty.
The Rada MX1 must only be supplied from the power adaptor provided.
The power adaptor must be connected to the xed wiring of the electrical supply via a switched
3A fused spur.
If the power adaptor supply cord is damaged the power adapter must be replaced by a competent
person.
The Rada MX1 has been certied for use in UK Healthcare premises as a TMV3 approved valve,
the approved designations of use are HP-WE.
For Healthcare installations refer to the TMV3 Requirements Manual which is available to view
or download from our website www.radacontrols.com.
Where chlorine disinfection is practised, DO NOT exceed a chlorine concentration of 50 mg/l (ppm)
in water, per one hour dwell time. Such procedures must be conducted strictly in accordance
with the information supplied with the disinfectant and with all relevant Guidelines/Approved
Codes of Practice.
The use of the word ‘failsafe’ to describe the function of any thermostatic mixing valve is both
incorrect and misleading. In keeping with every other mechanism it cannot be considered as
being functionally infallible.
Malfunction of thermostatic mixing valves can be detected by the use of proper temperature
checking and maintenance routines.
Certain types of system can result in the thermostatic mixing valve having excessive ‘dead-legs’
of pipework. Such systems can disguise the onset of thermostatic mixing valve malfunction.
Ultimately, the user must exercise due diligence to ensure that the delivery of warm water is at
a stable, safe temperature.
Make sure that the water delivery does not cause splashing or overow.
Allow su󰀩cient projection into the basin by ensuring the tap is mounted close enough to the vessel.
Important Safety Information
Make sure that the Rada MX1 is installed by a competent installer.
The product commissioning, clock (date/time) and tap set up can only be done in conjunction
with the “RADA AP1” available from the Apple APP store. Time and date setting is critical to
ensure data reporting is correct.
Note: Clock settings are lost after a period of 24hrs without mains power. When power is
restored clock settings return to factory default (1st February 2016) and will need to be reset
via the APP. Minimum charge time required for settings to be successfully set is 1 hour.

31367863-W2-E
Hereby, Kohler Mira Ltd. declares that the radio equipment type MX1 is in compliance with
Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following
internet address: www.mirashowers.co.uk.
The MX1 operates in the Frequency band 2402 MHz-2480 MHz with a maximum power of 0 dBm.
Specication
Electrical PSU Valve
Supply Voltage 100 - 240 V 50/60 Hz 12 V DC
Rated Input Current 1 A 2.0 A
Standby Current 0.16 A 0.16 A
Water Ingress Protection IP X4 IP X4
Protection Against Electric Shock Class II (double insulated) Class III (SELV)
Pollution Degree 2 2
Rated Impulse Voltage 2.5 kV 18 V
Performance
Factory pre-set temperature 39°C
Factory pre-set temperature range 37°C - 41°C
Programmable temperature range 33°C - 45°C (Full cold can be selected during
programming)
General PSU Valve
Maximum Ambient Temperature 50°C 40°C
Minimum Ambient Temperature 1°C 1°C
Maximum Humidity 95% rH 95% rH
Water Supply
Minimum dynamic pressure 100 kPa (1.0 bar)
Maximum dynamic pressure 500 kPa (5.0 bar)
Maximum static pressure 1000 kPa (10.0 bar)
Supply pressure di󰀨erential Equal pressure recommended - inlet pressures
must be stable for optimum performance.
Minimum recommended di󰀨erential
between hot supply and outlet temp
(consistent with HSE Guidelines)
7°C
Hot supply temp 55°C - 65°C (60°C - 65°C Recommended)
Cold supply temp 1°C - 25°C
Maximum disinfection temperature 85°C
For Type 3 installations, the supply conditions specied in the TMV3 Requirements manual take
precedence over the operating parameters which follow.

4
1367863-W2-E
Factory Default Settings
RADA App Tile / Section Adjustable
Temperature
Varient
Fixed
Temperature
Varient
Range
Units
Min Value Max Value
1. Valve Setup / 4. Installation Setup
1. Setup Advice Info Field
2. Valve Identity Editable Text Field
3. Outlet Type and Sub Type Info Field
4. Unit Address 17 17 1 31
5. Valve Date and Time 24 Hr Clock DD/MM/YYYY
6. Last Service and Time Info Field
7. Flow Calibration
8. Minimum Flow Limit 5 5 1100
9. Maximum Flow Limit 13 13 1 100
10. Valve DOB Info Field
11. Calibration N/A Set to max 300, 300
12. IR Calibration Factory Programmed - typical Range 180 - 220
13. Pin 0001 - 9999 Permisable. Re-entry of 5945 Not Permitted
14. Tap Interface Info Field
15. Operational State Enable Enable Enable, Disable
16. Tasks Apply Changes to Valve / Undo Changes
1. Valve Setup / 5. Outlet Setup
1. Type Info Field
2. Sub Type On/O󰀨 On/O󰀨 (On/O󰀨), Timed
Blocking N/A
3. Outlet Selection Info Field
4. Full Cold Mode Disabled Disabled
Start Cold
Enabled
Disabled
Start Cold
Enabled
Disabled
5. Minimum Temperature 37 N/A 33 45 0.5 deg C
6. Default Temperature 39 38 33 45
7. Maximum Temperature 41 N/A 33 45 0.5 deg C
8. Flow Rate Setup N/A
9. Default Flow Rate 50 50 10 100 %
10. Outlet Timeout 5 Min 5 Min 0s 30 Min Seconds / min
11. Run on Time 5 S 5 S 160 Seconds
12. Temperature Memory 40 S N/A 0 5 Min Seconds / min
13. Blocking Time 1 1 1 25 Min Seconds / min
14. Temperature Scale 9 Increments N/A 9, 5 Increments)
15. Tasks Apply Changes to Valve / Undo Changes
1. Valve Setup / 6. Duty Flush Setup
1. Activation Manual Manual Manual, Automatic

51367863-W2-E
* Flow rates are limited by the supply regulation of 2 L/min hot and cold 4 L/min.
2. Type
Standard Standard Disabled,
Standard,
Standard
oscillation
Disabled, Standard,
Standard oscillation
2. Type
Standard Standard Disabled,
Standard,
Standard
Oscillation, Smart,
Smart Oscillation
Disabled,
Standard, Standard
Oscillation, Smart,
Smart Oscillation
3. Activation Time 02:00 Hrs 02:00 Hrs Time 24 Hr
Clock
4. Duration 1 Min 1 Min 1 S 25 min Seconds / Min
5. Frequency 1 Per 3 Days 1 Per 3 Days 1 Hr 1 Week Hrs / day / 1
Week
6. Schedule Auto Populated Field
7. Temperature 39 39 37 41 deg C
8. Flow Rate 100 100 10 100 %
9. Warm Up Time 1 Min 1 Min 1 S 25 Min Seconds / Min
10. Post Cold Flush 00 0 10 Seconds / min
11. Tasks Apply Changes to Valve / Undo Changes
1.Valve Setup / 7. Cold Flush
Setup
1. Activation Manual Manual Manual, Automatic
2. Type Disabled Disabled Disabled, Standard
3. Activation Time 04:00 Hrs 04:00 Hrs Time 24 Hr
Clock
4. Duration 2 Mins 2 Mins 5 S 10 Mins Seconds / Min
5. Frequency 1 Per 3 Days 1 Per 3 Days 1 Hr 1 Week Hrs/Day/1Week
6. Schedule Auto Populated Field
7. Cool Down Temperature 19 19 15 <= Maintain Temperature deg C
8. Maintain Temperature 20 20 15 30 deg C
9. Cool Down Timeout 2 Mins 2 Mins 5 S 10 Mins Seconds / Min
10. Flow Test Start / Stop
11. Flow Rate 100 100 10 100 %
12. Task Apply Changes to Valve / Undo Changes
1. Valve Set Up / 8. Thermal
Disinfection Setup
1. Activation Manual Manual
2. Type Disabled Disabled Disabled, Standard, Exponential,
Standard Cold, Exponential Cold
3. Duration 20 20 130 Mins
4. Minimum Temperature 60 60 60 <=Upper deg C
5. Upper Temperature 60 60 >=Lower 80 deg C
6. Flow Rate 10 10 10 100 %
7. Warm Up Time 5 5 120 Mins
8. Timeout 30 30 159 Mins

6
1367863-W2-E
20 - 38 mm 0 - 20 mm
1 x Tap q
1 x Power Supply q
4 x Compression Nuts
(15 mm) q
4 x Olives (15 mm) q
1 x Flush Pipe q
2 x Fixing
Screws q
2 x Inlet Unit
Assemblies q
Pack Contents
2 x Fixing
Screws q
2 x Rigid Pipes q
1 x Tap Fixing Kit q
2 x Flexible Tails q
OR
2 x Reducers q
2 x Washers q

71367863-W2-E
Inlet Unit - Important
Failing to install the inlet units will cause product damage, invalidate the product’s
warranty and the product will no longer be TMV3 compliant.
The inlet unit is an integral component of the product consisting of a Filter / Flow
Regulator/ Check valve / Isolator.
The units are specic to hot and cold supplies, identied by a red / blue indices.
Flow direction is critical and is identied by the arrow on the unit’s body.
Filter contained in the unit is a ne 150 micron stainless steel mesh.
The ow regulators are included to the ensure the tap delivers a uniform ow and must
remain in situ for correct performance.
Separate Flow Regulator and
Check Valve for Hot Supply
Combined Flow Regulator and
Check Valve for Cold Supply
Filter
Filter
Housing
Check Valve
Housing
Isolator
Inlet Unit

8
1367863-W2-E
62 mm
155 mm
175 mm
110 mm
100 mm
300 mm
30°
320 mm
16 mm
55 mm
100 mm
44 mm
Dimensions
MX1 20

91367863-W2-E
221 mm
150 mm
30°
195 mm 63 mm
140 mm
320 mm
16 mm
55 mm
100 mm
44 mm
MX1 40

10
1367863-W2-E
PSU Mains Cable
2 m
PSU
TAP
PSU 12V Cable Extension Cable
Total Cable Run: 1.09 m
Total Cable Run with Extension Cable: 3.59 m
Product Tail
1.0 m 2.5 m 0.09 m
Power Supply Unit (PSU)
Disposal and Recycling
Make sure that you install the PSU in an area that you can access easily for servicing
and maintenance purposes.
Ensure plugs and sockets are completely dry before making any connection, including
any accidental water contact.
Ensure connections are not in an area exposed to excessive moisture or condensation.
DO NOT exceed the maximum cable run of 3.59m, doing so would invalidate electrical
approval.
End of Product Life
Electrical and electronic devices contain a range of materials that can be separated
for recycling and used in new products.
This product should not be disposed of with your general household waste.
When this product has reached the end of its serviceable life, please remove
any batteries and take it to a recognised WEEE (Waste Electrical and
Electronic Equipment) collection facility such as your local civic amenity
site for recycling.
Your local authority or retailer will be able to advise you of your nearest recycling facility.