Konica Minolta BIZHUB 250/350 Instruction and safety manual

V1.2
The Konica Minolta Guide to LDAP
This guide details how to set up the:
Bizhub 250/350, 420/500, 361/421/501, 600/750
Bizhub C250, C252, C300, C351, C352, C450
Bizhub C203
,
253
,
451
,
,
550
,
650
Created by Hotline Suppor
t
Konica Minolta Hotline Support (UK)

LDAP, Lightweight Directory Access Protocol, is an Internet protocol that
Konica Minolta machines can use to look up E-Mail
Addresses from a server running Active Directory with LDAP Service*
*Server 2008, LDAP is installed separately to Active Directory*
To set up LDAP on the Konica Minolta Bizhub machines, please follow the instructions
below: NB: this is a guide only and is not indicative of actual settings for your
network or machine as the LDAP structure varies from Network to Network and
machine.
It is advisable for the Network Administrator to configure settings as a knowledge of
the Network is required.
C250, 252, C300, C351, C352, C450, BH420/BH500, BH600/BH750
Setting up via the Control Panel –
1) Press on Utility/Counter
2) Press on Administrator Setting and enter the Admin code of 12345678
3) Press on Network Setting
4) Press on LDAP Setting
5) Press on ‘Enabling LDAP Function’ and select ‘ON’. Press ‘OK’
6) The machine will then take you out of Network Settings and you will have to follow
steps 3 & 4 again
7) Press on ‘Setting Up LDAP’ and the following screen will appear
8) Enter the IP address of the server where LDAP is configured
9) Enter in the ‘Search Base’ of the domain.

As a rough guide you can find the domain by right clicking ‘My Computer’ and going
in to the Properties. Under the ‘Computer Name’ tab it will say ‘Domain’ as below.
The basic rule for the Search Base is if the customer has a separate container of
employee e-mail addresses that are outside of the root of the domain this must also
be specified. If they do not, you only need to input the root.
For example, the customer has a container called Sales, and his domain is
mydomain.co.uk. The search base would be: ou=Sales,dc=mydomain,dc=co,dc=uk
Without the Sales container, it would be dc=mydomain,dc=co,dc=uk(Searches entire
domain)
My Computer Properties
10) Press the ‘FWD’ button to progress to the next screen
11) These next settings are very much dependent on the customer’s server and how
it has been set up. For example, the Hotline in Basildon runs on a different network
to the LDAP server. On our machines, we have to set the ‘General Settings’ to
‘Simple’ but on the next screen we have to force the domain within the User Name.
On other machines in the building that are on the same network as the server,
‘General Settings’ are set to GSS-SPNEG0 and the domain does not need to forced.

12) Press the ‘FWD’ button to progress to the next screen
13) Enter the ‘Login Name’ and ‘Password’ of an account that is set up on the server.
14) Enter in the ‘Domain Name’ as discovered in Step 9.
15) Press the ‘FWD’ button to progress to the next screen
16) Set as required
Set up of LDAP is now complete.
T
his is us
forcin
g
the
domain
On the machine, a ‘Check Connection’ button will appear here. Once you
have entered the settin
g
s, press on this button to ensure the machine can
see the LDAP server

You can also set this up via a web browser.
To do this, follow the instructions below:
1) Enter the IP address of the Konica Minolta machine into Internet Explorer and
press Go
2) Log into the web page using the Admin code for the machine. Depending on
which machine you have, this will either be 8 x 0’s (00000000) or 12345678.
3) Click on the Network tab at the top of the screen
4) Then click on LDAP
5) Once you have input the settings, be sure to click on ‘Check LDAP Setting’

Bizhub 250/350
Setting up via the Web Browser-
It is easier to configure the Bizhub 250/350 via the web interface.
1) Log into Admin Mode using the code of 8 x 0’s (00000000) and click on
the Network tab. Make sure you enable LDAP under the ‘LDAP’ heading
before you go into ‘LDAP Server Setting’
2) Select any available set of 3 dashes(allowed up to 5 servers) we will
assume Hot2003 does not exist
3) The LDAP Server screen opens as below, you may need to force the domain as
shown. Search base will be your FQDN in dc=, format. Domain Name would be
your normal domain logon name.
Forcing the
Domain

Bizhub C203 – 650 (Bizhub 361-501 is similar)
Setting up via the Control Panel –
At Machine:
1. Press Utility/Counter
2. Press “Administrator Settings”
3. Enter the Administrator Password, default = 12345678 and press “OK”
4. Press “Fax Settings”

5. Press “Function Settings”
6. Press “Forward TX Setting”
7. Press all as arrowed then “Select from Address Book”

8. Here you have a couple of options, you can select “Index” and search for a
recipient or select “Destination Type” and “E-Mail” then select the recipient.
The latter is shown below
8. Press “OK” you will then be returned to the screen as in 7 only this time
you will see your selected recipient in the Forward Dest. Dialogue box.
9. Press “OK” then “Close” until back to main screen
Setting up via the Web Interface-

1. Enter the IP address of the Konica Minolta machine into Internet Explorer
and press Go
2. Log into the web page using the Admin code for the machine.
Default = 12345678.
3. Click on the Network tab at the top of the screen
4. Then click on LDAP Setting and set to Enable
4) Select “Setting Up LDAP” and select any available radio button. we will
assume Hot2003 does not exist.
5. Select “Edit”
6. Enter you network settings in the dialogue box’s including password. The copier will
use the Admin credentials to interrogate LDAP (none of this is seen by end user)