Korenix JetWave 4020 Series User manual

Appearance
JetWave 4020/4020E Series
Industrial 802.11ac + 802.11n 2.4G WIFI AP, 2xGT + USB M12
Quick Installation Guide V1.0
R&TTE Directive 1999/5/EC Declaration
The product may be operated in all European Union countries. While you see the CE Marking
printed on our product, it indicates the product complies with the requirement of the R&TTE
(1995/5/EC) Directive. You can download the formal document of the product from our Web
site or send inquiry to our Sales/Technical people.
General Requirement
Only trained and qualified personnel should be allowed to install, replace, or service this
equipment. The device can only be operated according to the technical specification. Read the
installation instructions/user manual, including Power, Cable, Antenna, Warning info and well
Grounding is must before connecting the system to the power source.
DC Input
The device supports dual DC power input or Passive PoE input, the typical power source is DC
24V (±15%) or DC 110V depends on the model you purchase. For passive PoE input, please
purchase the injector from us, the device do NOT accept force mode from PSE switch.
Installation
The Korenix View Utility provides you convenient tool to scan the network and configure
the connected Korenix device.
Step 1: Open the Korenix View Utility. (Must later than V1.6.11)
Step 2: Select the correct NIC (Network Interface Card) from the NIC list.
Step 3: Click “Discovery”, and then the Nodes and its IP address can be found and listed in
Node list.
Step 4: After you scan the network, select the device
and click “Open Web GUI” to access the web
management interface. You can also modify the IP
address/Netmask directly on the selected entry and
then click “Change IP“ to change IP settings.
Note: Please check the User Manual to configure the
other software settings.
3 Years Warranty
Each of Korenix’s product is designed, produced, and tested with high industrial standard.
Korenix warrants that the product(s) shall be free from defects in materials and
workmanship for a period of three (3) years from the date of delivery provided that the
product was properly installed and used.
This warranty is voided if defects, malfunctions or failures of the warranted product are
caused by damage resulting from force measure (such as floods, fire, etc.), other external
forces such as power disturbances, over spec power input, or incorrect cabling; or the
warranted product is misused, abused, or operated, altered and repaired in an unauthorized
or improper way.
Attention! To avoid system damage caused by sparks, please DO NOT plug in power
connector when power is on.
The product is in compliance with Directive 2002/95/EC and 2011/65/EU of the
European Parliament and of the Council of 27 January 2003 on the restriction of the use of
certain hazardous substances in electrical and electronics equipment (RoHS Directives &
RoHS 2.0)
Korenix Customer Service
KoreCARE is Korenix Technology's global service center, where our professional staffs are
ready to solve your problems at any time.
Korenix global service center: [email protected].
Document download: http://www.korenix.com -> Download
Support
Korenix View Utility
The JetWave 4020 Series provides web management interface for basic and advanced settings.
Before configuration, please make sure your system meets the following requirements:

A computer coupled with 10/100/1000 Base-T(X) adapter.

Configure the computer with a static IP address of 192.168.10.X/192.168.1.X (X cannot
be 0, 1, nor 255).

The product works as Router mode in default. The GT2(LAN) default IP address is
“192.168.10.1”, and GT1 (WAN) default IP is “192.168.1.1”

The WIFI default setting of JetWave 4020 is AP mode, Radio1 SSID is “JetWave_1”,
operate in 2437MHz(channel 6).Radio2 SSID is “JetWave_2”, operate in 5180MHz(channel
36).

Open web browser (Ex: IE, Chrome, Firefox…) and enter the IP address of the product.
You will see the System Login page.

The default User Name is “admin”.

The default Password is “admin”.

Check User Manual for advanced settings.

If the web browser is not access, please check your firewall or contact your support
window for further help.
Note: If you forget the IP Address, you can use Korenix View Utility to search the device’s IP
address, it can be found at Download page of the Korenix web site: http://www.korenix.com
Web GUI
Model Name
Radio 1
Radio 2
Antenna
2x GT M12 X-code (GT1 accepts passive PoE input),
1x M12 A-code 24VDC, 1x M12 A-code USB/Console
JetWave 4020
802.11n 2.4GHz
802.11ac 5GHz
Embedded 9/10dBi
JetWave 4020E
802.11n 2.4GHz
802.11ac 5GHz
External N-Type
Connector
Radio Information
4
3
5
6
1
2
8
7
Ethernet
1 ----- 0P
2 ----- 0N
3 ----- 1P
4 ----- 1N
5 ----- 3P
6 ----- 3N
7 ----- 2N
8 ----- 2P
2
3
7
5
8
46
1
USB + Console
1 ----- TX
2 ----- RX
3 ----- GND
4 ----- GND
5 ----- USB DP
6 ----- USB DM
7 ----- USB +5V
8 ----- GND
1
43
2
Power Input
2:+ 1:+
3:- 4:-
Upper panelLower panel
Vent Ground
GT2 GT1
WLAN 1
(2.4G)
WLAN 2
(5G)
2x DC input
24V or 110V
USB+
Console
JetWave 4020
Embedded Ant.
(2.4G 9dBi +
5G 10dBi)
JetWave 4020E
4x N-Type Ant.
Grounding
RF
Cable
Lightening
Protection
Arrestor
Mounting method:
Step1: Assemble case plate with 4x screws to the
bottom of JetWave unit.(Toward A)
Step2: Assemble ①and ②, and lock up with ③
Step3: Assemble ④to ⑤if you need to use pole
mounting
4
2
1
3
Wall
Pole
Mount
A
A
A
A
5
wall plate
Case plate

JetWave 4020 equips with dual band 2.4G+5G embedded
antenna, it can provide 180owide range coverage.

JetWave 4020E equips with the external N-Type antennas for
short or long distance wireless communication. Choose the
suitable antenna you need.

Connect the Ethernet cable, power cable with M12 connector.

Well grounding the device before power on the system.

Connect Surge Protection Arrestor at Antenna socket is
important to protect your system on field.
M12 Connector
Mounting The Unit/Antenna and well Ground is MUST

R&TTE指令1999/5/EC宣告
该产品可在所有欧盟国家进行操作。当你看到印在我们的产品的CE标示，则表明产
品符合R＆TTE（1995/5 / EC）指令的要求。您可以从我们的网站下载该产品的正式
文件或发送请求到我们的销售/技术人员。
Radio信息
3 年质保
Korenix的产品，在设计，生产和测试过程都遵循高的工业标准。Korenix保证其产
品从交货起三年内无材料和工艺缺陷，但必须确保产品被正确地安装和使用。
质保产品由下情况造成的缺陷，失效或故障不在质保范围：由强制实施造成的（
如洪水，火灾等），其它外部力量，如电源干扰，过规格电源输入，或者接线错
误，或者产品被误用，滥用，或者由未授权或不当的方式运行，改造和维修。
注意! 为了避免火花损坏系统, 请不要在带电的情况下插入电源接头。
我们的产品符合欧洲2002/95/EC，2011/65/EU标准和理事会在2003年1月21日关于
限制电气和电子设备使用某些有害物质条例 (RoHS 条例 & RoHS 2.0) /。
Korenix 客户服务
KoreCARE是Korenix科技的全球服务中心，在那里我们的专业人员随时为你解决
问题。
Korenix 全球服务中心: [email protected].
文件下载: http://www.korenix.com -> Download
客户服务
外观说明
Patent No. (Taiwan):
Granted Invention: I 313547
Granted Invention: I 321415
Granted Invention: I 344766
Granted Invention: I 346480
Granted Invention: I 356616
Granted Invention: I 364684
Granted Invention: I 376118
Granted Invention: I 393317
Granted Invention: I 398066
Granted Invention: I 398125
Granted Invention: I 459757
Utility Model: M 339841
Utility Model: M 339840
DC 输入
该设备支持双直流电源输入或被动的PoE输入，典型的电源为DC 24V（±15％）或
DC 110V取决于你购买的型号。对于被动的PoE输入，请购买我们的馈电器，设备不
接受PSE交换机的强制模式。
新款的Korenix查看工具是理软件方便您搜寻网络地址与部分基本设定。
步骤 1：打开 Korenix View Utility管理软件 (必须是V1.6.11 版之后) 。
步骤 2：在网络卡列表中选取指定的网络卡或选All Interface(全部) 。
步骤 3：按下 “Discovery” (搜寻), 接着所有此网络的Korenix交换机/AP/网关和它们
的产品名称，IP地址，MAC地址，Netmask位址与软件版本…等讯息将可以被找到
，并显示在设备列表下。
步骤 4：在搜寻到设备后，选取指定设备按下鼠
标右键“Open Web GUI”即可允许您直接连上Web
设定接口，妳也可以于此直接修改IP/Netmask地
址后按下“Change IP“ 直接修改其设定。
备注: 其他进阶软件设定部分请参考用户使用手
册。
Korenix 查看工具
JetWave 4020系列提供网页管理接口来进行基本和高级设置。配置之前，请确保您的
系统满足以下要求：

一台具有10/100/1000 Base-T(X) 网络接口的计算机。

设定一组静态IP地址 192.168.10.X (X 不可为0、1或255) 到这台计算机。若是连接
在WAN接口，請设定一组静态IP地址 192.168.1.X 。

产品默认工作为路由模式。GT2是LAN端口，默认IP地址为“192.168.10.1” ，GT1
是WAN端口，默认IP地址为“192.168.1.1” 。

JetWave 4020 WIFI 默认设置为AP模式, Radio1 SSID 是“JetWave_1” ，工作在
2437MHz(channel 6); Radio2 SSID 是“JetWave_2” ，工作在5180MHz(channel 36)。
打开web浏览器 (Ex: IE, Chrome, Firefox…)，输入产品IP地址。您会进入系统登录页
面。

默认的用户名是“admin”。

默认的密码是 “admin”。

参阅用户手册进行高级配置。

如果Web浏览器无法访问, 请检查你的防火墙或者联系您的支持窗口寻求进一步
帮助。
注意: 如果你忘记了设备IP地址, 可以使用Korenix View工具来搜索设备IP地址，可以
通过Korenix网页的下载页面下载 ：http://www.korenix.com
Web 软件接口
概述 安装
Korenix Technology Co., Ltd.
(A Beijer Electronics Group Company)
Tel:[phone]
Fax:[phone]
Business service:[email protected]
Customer service:[email protected]
www.korenix.com
CPQ000W4020000
Model Name
Radio 1
Radio 2
Antenna
2x GT M12 X-code (GT1 accepts passive PoE input),
1x M12 A-code 24VDC, 1x M12 A-code USB/Console
JetWave 4020
802.11n 2.4GHz
802.11ac 5GHz
Embedded 9/10dBi
JetWave 4020E
802.11n 2.4GHz
802.11ac 5GHz
External N-Type
Connector
4
3
5
6
1
2
8
7
Ethernet
1 ----- 0P
2 ----- 0N
3 ----- 1P
4 ----- 1N
5 ----- 3P
6 ----- 3N
7 ----- 2N
8 ----- 2P
2
3
7
5
8
46
1
USB + Console
1 ----- TX
2 ----- RX
3 ----- GND
4 ----- GND
5 ----- USB DP
6 ----- USB DM
7 ----- USB +5V
8 ----- GND
1
43
2
Power Input
2:+ 1:+
3:- 4:-
Upper panelLower panel
Vent Ground
GT2 GT1
WLAN 1
(2.4G)
WLAN 2
(5G)
2x DC input
24V or 110V
USB+
Console
JetWave 4020
Embedded Ant.
(2.4G 9dBi +
5G 10dBi)
JetWave 4020E
4x N-Type Ant.
Grounding
RF
Cable
Lightening
Protection
Arrestor
只有经过培训的合格人员才能安装，更换或维修此设备。该设备只能按照技术规范
进行操作。系统上电之前请阅读安装说明/用户手册，检查包括电源，电缆，天线，
警示信息和良好的接地。
支架安装方式:
步骤一: 使用4颗螺丝, 将case plate锁在
JetWave设备底部的四个螺丝孔位
步骤二: 组装①跟②, 并使用③将其锁住
步骤三: 若需在柱杆上安装, 请将④穿进⑤
中, 并圈在柱杆上
4
2
1
3
Wall
Pole
Mount
A
A
A
A
5
wall plate
Case plate
安装设备/天线，良好接地是必须的

JetWave 4020 配备双频段2.4G+5G嵌入式天线, 它提供
180∘宽范围覆盖。

JetWave 4020E 配备外置N-Type天线来进行短距和长距
无线通信。 选择您所需的适合天线。

连接M12头的以太网电缆和电源电缆。

在通电之前系统必须良好接地。

在天线插座上连接浪涌保护避雷器是非常重要的来保
护您现在系统。
M12 接头