Korenix JetNet 6059G User manual

1
JetNet 6059G Series
9-Port Gigabit Managed Ethernet Switch
User’s Manual
V1.2, 21-Sep-2012
Firmware v1.2
www.korenix.com

2
JetNet 6059G Series
Industrial Managed Gigabit Ethernet Switch
User’s Manual
Copyright Notice
Copyright 2011 Korenix Technology Co., Ltd.
All rights reserved.
Reproduction in any form or by any means without permission is prohibited.

3
Declaration of CE
This product has passed the CE certification for environmental
specifications. Test conditions for passing included the equipment being
operated within an industrial enclosure. In order to protect the product
from being damaged by ESD (Electrostatic Discharge) and EMI leakage,
we strongly recommend the use of CE-compliant industrial enclosure
products.
Federal Communications Commission (FCC) Statement
This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instruction manual,
may cause harmful interference to radio communications. Operation of
this equipment in a residential area is likely to cause harmful interference
in which case the user will be required to correct the interference at his
expense.
The user is cautioned that changes and modifications made to the
equipment without approval of the manufacturer could void the user's
authority to operate this equipment.

Index
1 Introduction........................................................................................................................... 1
1.1 Overview ....................................................................................................................1
1.2 Major Features...........................................................................................................2
1.3 Package List ..............................................................................................................3
2 Hardware Installation........................................................................................................... 4
2.1 Hardware Introduction ...............................................................................................5
2.2 Wiring the Power Inputs ............................................................................................8
2.3 Wiring Digital Input ..................................................................................................10
2.4 Wiring Digital Output................................................................................................10
2.5 Wiring Earth Ground................................................................................................11
2.6 Wiring Gigabit Ethernet RJ-45 Ports ......................................................................12
2.7 Wiring Combo Ports –SFP.....................................................................................13
2.8 Wiring RS-232 Console Cable................................................................................13
2.9 DIN-Rail Mounting Installation ................................................................................14
2.10 Wall-Mounting Installation .......................................................................................15
3 Preparation for Management............................................................................................ 17
3.1 Preparation for Serial Console................................................................................18
3.2 Preparation for Web Interface.................................................................................19
3.3 Preparation for Telnet Console ...............................................................................22
4 Feature Configuration ....................................................................................................... 25
4.1 Command Line Interface Introduction ....................................................................26
4.2 Basic Setting............................................................................................................31
4.3 Port Configuration....................................................................................................52
4.4 Network Redundancy ..............................................................................................62
4.5 VLAN........................................................................................................................82
4.6 Private VLAN ...........................................................................................................92
4.7 Traffic Prioritization ..................................................................................................98
4.8 Multicast Filtering...................................................................................................103
4.9 SNMP.....................................................................................................................109
4.10 Security ..................................................................................................................113
4.11 Warning..................................................................................................................120
4.12 Monitor and Diag ...................................................................................................129
4.12 Device Front Panel................................................................................................137
4.13 Save to Flash.........................................................................................................138
4.14 Logout ....................................................................................................................139
5 Appendix ........................................................................................................................... 140
5.1 Product Specifications...........................................................................................140
5.2 Korenix SFP family ................................................................................................146
5.3 Korenix Private MIB...............................................................................................147
5.4 Modbus TCP protocol............................................................................................148
5.5 Revision History.....................................................................................................160
5.6 About Korenix ........................................................................................................161

1
1 Introduction
Welcome to Industrial 9-port Managed Gigabit Ethernet Switch User
Manual. Following topics are covered in this chapter:
1.1 Overview
1.2 Major Features
1.3 Package Checklist
1.1 Overview
The Industrial 9-port Managed Gigabit Ethernet Switches, have 4
10/100/1000Base-TX ports and 5 combo ports, respectively 10/100/1000
RJ-45 / 100-FX / Gigabit SX/LX. The Switch is especially designed to
operate under harsh environmental conditions. The switches provide solid
foundation for a highly fault-tolerant and easily-managed network. It can be
remotely configured by Telnet, Web browser, JetView and managed by
Simple Network Management Protocol (SNMP) and Remote Monitoring
(RMON). You can also connect the attached RS232 console cable to
manage the switch by Command Line Interface (CLI). CLI commands are
Cisco-Like commands, your engineers who are familiar with Cisco products
don’t need to learn new rules for CLI commands.
Security is enhanced with advanced features such as 802.1Q VLAN and
Port/IP security. Performance is optimized by QoS and IGMP
Snooping/Query. Korenix 3nd generation Ring technology, Multiple Super
Ring, enables superb self-healing capability for network failure. The fastest
failover time is enhanced from 300ms to 5ms for 10/100TX RJ-45 ports,
and 30ms for 100FX and Gigabit Fiber. This is Korenix patented ring
technology, which is registered in most countries. For interoperability with
your existed network, the Switch also comes with an advanced redundant
network solution, Ring Coupling and Rapid Dual Homing technology. With
Ring Coupling and Rapid Dual Homing technology, Ethernet Ring can be
extended more easily. No matter with Korenix switch or other managed
switches.
The IP31-design aluminum case further strengthens Switch's withstand
ability in harsh industrial environment. The event warning is notified to the
network administrator via e-mail, system log, or to field engineers by relay
output. The Industrial Managed Gigabit Ethernet Switch has also passed
CE/ FCC certifications to help ensure safe and reliable data transmission

2
for industrial applications. It will be your best choice for highly-managed
industrial network.
1.2 Major Features
The Switch has the following features:
4 Gigabit copper ports, 5 Gigabit copper/SFP combo ports to extend
Giga Copper/Fiber uplink or Giga Copper/Fiber Ring connection
SFP support 100/1000 Fiber with Digital Diagnostic Monitoring (DDM)
for transmission quality monitoring
Independent 100Mbps / 1000Mbps SFP speed indication
32Gbps switch Fabric, 8K MAC address to ensure High Quality Data
transmission
Isolated out-band management interface for negative power system.
Korenix patented MSR® pattern aggregates up to 4 x 1000M Rings for
critical data stream redundancy
IEEE 802.1AB LLDP and optional JetView Pro i2NMS software for
auto-topology and group management
Advanced management by LACP/ 256 VLANs/ GVRP/ QoS/ IGMP
Snooping/Rate Control/ Online Multi-Port Mirroring/DHCP option 82
Advanced Security system by Port Security, Access IP list, SSH
(Secure Shell) for Telenet security and Hypertext Transfer Protocol
Secure (HTTPS) with SSL protocol for Web Browsering Security
Event Notification through E-mail, SNMP trap and SysLog
Cisco-Like CLI, Web, SNMP/RMON for network Management
Compliant with NEMA -TS2 /Marintime/ Railway EMC inquires
Dual redundant 10.5~60VDC power inputs for system reliability
AC 1.5KV Hi-pot isolation and -25~70℃operating temperature for
harsh environments. -40~75℃: -w model ; UL 60950-1 enviroment:
-25~60°C or -40~60°C.
The detail specifications is listed in Appendix- 5.1
Note-1: those certifications are pending for special project request, please
contacts your sales contact window.

3
1.3 Package List
The Switch is shipped with following items:
Ethernet Switch x1
One DIN-Rail clip (attached to the switch)
One wall mounting plate
One RS-232 DB-9 to RJ-45 console cable
CD User manual x 1
Quick Installation Guide (QIG)
If any of the above items is missing or damaged, please contact your local
sales representative.
QIG
CD User
Manual
DB-9 to RJ-45
Cable
JetNet 6059G

4
2 Hardware Installation
This chapter includes hardware introduction, installation and
configuration information. Following topics are covered in this chapter:
2.1 Hardware Introduction
Dimension
Panel Layout
Bottom View
2.2 Wiring Power Inputs
2.3 Wiring Digital Input
2.4 Wiring Relay Output
2.5 Wiring Ethernet Ports
2.6 Wiring Combo Ports
2.7 Wiring RS-232 console cable
2.8 DIN-Rail Mounting Installation
2.9 Wall-Mounting Installation

5
2.1 Hardware Introduction
Dimension
The industrial 9-port Gigabit managed Switch dimension is: 95mm x
167.65mm x 127.2mm (W x H x D), w/o DIN Rail
95mm x 167.65mm x 146.9mm (W x H x D), w/o DIN Rail Clip

6
Front Panel Layout
The front panel includes 10/100/1000Mbps Gigabit Ethernet ports, SFP slot, RS232 console
port, Reset button and LEDs for system and port indication.
The LED function is decribed as following table:
LED
Function
Behaviors
Power 1,2
Indicates the power input status
On: the input connector is on applying
power.
SYS
Indicates the system operating
status
Green On: System is ready to operating
D.I.
Indicates the digital input status
On: High level signal is applied
D.O.
Indicates the digital output (Relay
output) status
On: the output is formed close circuit
R.S.
Indicates the ring operating status.
Ring Status: Green on (Ring normal)
/Blinking (Ring with wrong port); Yellow
on (Ring abnormal) / Blinking (device's
ring port failed)
Link/Active
Indicates the traffic status and link
status
Green On: port is linked with partner.
Blinking: the traffic is active.
Speed
Indicates the copper port link speed
Yellow On: port is link at 1000Mbps.
Yellow Off: port is link at 100Mbps or
10Mbps.
1000M
SFP transceiver speed indication
On: the SFP transceiver supports
1000Mbps

7
Bottom View
The bottom view of the the Industrial 9-port Gigabit Managed Switch consists of two terminal
block connectors with two DC power inputs, one Digital Input (DI), one Relay Output (DO)
and one Chassis Grounding screw.
Note: The unit intended to use vertical direction, with
DIN-rail or wall-mount only.

8
2.2 Wiring the Power Inputs
Follow below steps to wire the Switch’s redundant DC power inputs.
1. Insert positive and negative wires into V+ and V- contacts respectively of the terminal
block connector
2. Tighten the wire-clamp screws to prevent DC wires from being loosened.
3. Power 1 and Power 2 support power redundancy and polarity reverse protect function.
That means with wrong polarity, the system won’t work.
4. Positive and negative power system inputs are both accepted, but Power 1 and Power 2
must apply with same mode as following figures.
Note 1: It is a good practice to turn off input and load power, and to unplug power terminal
block before making wire connections. Otherwise, your screwdriver blade can inadvertently
short your terminal connections to the grounded enclosure.
Note 2: The range of the suitable electric wire is from 12 to 24 AWG.

9
Note 3: If the 2 power inputs are connected, the Switch will be powered from the highest
connected voltage. The unit will alarm for loss of power, either PWR1 or PWR2.
Note 4: To use the UL Listed LPS Power supply with output Rating 10.5-60 Vdc, minimum
2 A. Here, we recommended use DC 24V as the operating voltage.
Note 5: Both of power inputs should apply with same electrical power system; mixing
positive and negative electrical power system will make system damage.
Note 6: Once power on the device, the system LED will activate by the sequence as table
following:
Indicators
Stage 1
Stage 2
Stage 3
Stage 4
Stage 5
Stage 6
Power LED
On
On
On
On
On
On
DI
Off
On
Off
Off
Off
Off
DO
Off
Off
On
Off
Off
Off
R.S.
Off
Off
Off
On
Off
Off
SYS
Off
Off
Off
Off
Off
On
Description
Power on
Ex. Booter
Ld. firmware
Ex. firmware
System booting
System Ready
(Ex: executes; Ld: Load)
By those LED indicators, we can know the exactly stage is performed by system during the
power on.

10
2.3 Wiring Digital Input
The Switch provides one digital input. It allows users to connect the termination units’
digital output and manage/monitor the status of the connected unit. The Digital Input pin
can be pulled high or low; thus the connected equipments can actively drive these pins
high or low. The embedded software UI allows you to read and set the value to the
connected device.
The power input voltage of logic low is DC 0~10V. Logic high is DC 11~30V.
.
2.4 Wiring Digital Output
The Switch provides one digital output, also known as Dry Relay Output. The relay
contacts are energized (open) for normal operation and will close for fault conditions. The
fault conditions include power failure, Ethernet port link break or other pre-defined events
which can be configured in Switch’s UI.

11
2.5 Wiring Earth Ground
To ensure the system will not be damaged by noise or any electrical shock, we suggest
you to make exact connection between the Switch and Earth Grounding system.
On the bottom side of the Switch, there is one earth ground screw. Loosen the earth
ground screw by screw drive; then tighten the screw after earth ground wire is well
connected.

12
2.6 Wiring Gigabit Ethernet RJ-45 Ports
The Ethernet Switch adopts 9 ports RJ-45 connectors which support 10/100Mbps
Half/Full duplex, 1000Mbps full duplex with auto MDI/MDI-X functions and auto
negotiation; there are 5 in 9 ports RJ-45 are combo with SFP socket which supports
optical fiber communication that can support 100Mbps and 1000Mbps SFP Transceiver
with Digital Diagnostic Monitor (DDM) feature to achieves fiber signal quality control.
All the RJ-45 ports will auto-detect the signal from connected devices to negotiate the link
speed and duplex mode. Auto MDI/MDIX allows users to connect another switch, hub or
workstation without changing straight through or crossover cable.
Note: that crossover cables simply cross-connect the transmit lines at each end to the
received lines at the opposite end.
Connect one side of an Ethernet cable into any switch port and connect the other side to
your attached device. The LNK LED will light up when the cable is correctly connected.
Refer to the LED Indicators section for descriptions of each LED indicator. Always make
sure that the cables between the switches and attached devices (e.g. switch, hub, or
workstation) are less than 100 meters (328 feet).
The supports cable types are as below.
1000 Base-TX: 4-pair UTP/STP Cat. 5e cable, EIA/TIA-568B 100-ohm (100 meters)
10/100Base-TX: 4-pair UTP/STP Cat. 5 Cable, EIA/TIA-568B 100-ohm (100 meters)

13
2.7 Wiring Combo Ports –SFP
The Switch includes 5 RJ-45/ SFP socket combo ports. The speed of the gigabit Ethernet
RJ-45 port supports 10Base-T, 100Base-TX and 1000Base-T. It also equips 5 gigabit
SFP ports combo with gigabit Ethernet RJ-45 ports. The speed of the SFP port supports
100Base-FX and 1000Base-SX/LX and accepts standard MINI GBIC SFP transceiver.
For the system reliability, Korenix recommends using the Korenix certificated Gigabit SFP
Transceiver, especially the DDM function. Korenix‘s DDM type of SFP transceiver have
modified with higher accuracy. With the non-certified DDM SFP transceiver, the DDM
features will be disabled.
To keep best performance, the SFP fiber ports will not support Fiber Link First function
anymore after firmware version v1.1; Since, the SFP fiber transceiver vendor have applied
energy saving technology and changed the circuit design that will cause SFP transceiver
can’t offer energy of fiber link signature to switches the connection from RJ-45 to fiber,
even the SFP fiber transceiver already link up.
To fix that issue, new firmware have applied plug-in and switch to fiber mode feature. It
forced the connection change from RJ-45 to SFP immediately, once the SFP transceiver
inserted and detected by CPU.
Note: The Ethernet Switch has to use UL recognized fiber transceiver with Class 1
Laser/LED Diode.
Note: It is recommended don’t plug-in SFP fiber transceiver and link up RJ-45 port at
same time, it might cause the connection does not work properly.
2.8 Wiring RS-232 Console Cable
There is one RS-232 DB-9 to RJ-45 cable shipped with the box. Connects the DB-9
connector to the COM port of your PC, open Terminal tool and configure the serial
communication parameter to 9600, N, 8, 1. (Baud Rate: 9600bps / Parity: None / Data
length: 8bits / Stop Bit: 1) Then you can access CLI interface by console cable.
The RS-232 interface is uses isolated design and the RJ-45 shield is connects to chassis
grounding. Be sure the console cable you connected is not shielded when it connects to
DTE (desktop PC) which uses different electrical power system.
Note: If you lost the cable, please contact with your sales or follow the pin assignment to
buy a new one. The Pin assignment spec is listed following.
RJ-45 Pin
DB-9 Pin
Description
1
8
N/A
2
9
N/A
3
2
TxD
4
1
N/A
5
5
GND
6
3
RxD
7
4
N/A
8
7
N/A
(Updated pin assignment)
DB-9 Female Connector

14
2.9 DIN-Rail Mounting Installation
The DIN-Rail clip is already screwed tighten on the rear side of Switch when shipping. If
the DIN-Rail clip is not screwed on the Ethernet-Switch, contact your sales respresentive.
The DIN rail clip supports EN50022 standard. In the diagram following includes the
dimension of EN50022 DI rail for your refer.
Follow the steps below to mount the Switch to the DIN-Rail track:
1. First, insert the DIN-Rail track upper side into the upper end of DIN-Rail clip.
2. Lightly push the bottom of DIN-Rail clip into the track.
3. Check if DIN-Rail clip is tightly attached on the track.
4. To remove Switch from the track, reverse the steps above.
Notes: The DIN Rail should compliance with DIN EN50022 standard. Using wrong DIN rail may
cause system install unsafe.
1. Use the screws to attach DIN-Rail clip to the real panel of JetNet 6059G.
2. To remove DIN-Rail clip, reverse step 1.

15
2.10 Wall-Mounting Installation
Follow the steps below to install the Switch with the wall mounting plate.
1. To remove DIN-Rail clip from Switch, loosen the screws from DIN-Rail clip.
2. Place the wall mounting plate on the rear panel of Switch.
3. Uses the screws loosed from the DIN rail to screw tighten the mounting plate onto the
Switch.
4. Use the hook holes at the corners of the wall mounting plate to hang or screw on
JetNet Switch onto the wall. Following screw specifications are for different mounting
ways.
Screw and hang on the wall (8.4mm hang-hole): uses M3 screw with screw nut
diameter between 5mm to 8.4mm).
Directly screw on the wall (4.2mm screw-hole): uses M3 screw with nut diameter
over 5mm.
5. To remove the wall mounting plate, reverse the steps above.
Note: To avoid damage the internal circuit, be sure use the screw included in the package to

16
screw and tight the wall-mount kit onto the rear side of the Switch. The specification of screw
is M3 in 6 mm length.