Korenix JetNet 5310G User manual

JetNet 5310G User Manual
1
Korenix JetNet 5310G
Industrial 8-Port PoE + 2 Gigabit TX/ SFP
Managed Ethernet Switch
User Manual
Ver. 06, July-2013
Firmware V1.2a
www.korenix.com

JetNet 5310G User Manual
2
Korenix JetNet 5310G
Industrial 8 Port PoE + 2 Gigabit TX /SFP
Managed Ethernet Switch
User’s Manual
Copyright Notice
Copyright 2012 Korenix Technology Co., Ltd.
All rights reserved.
Reproduction in any form or by any means without permission is prohibited.

Federal Communications Commission (FCC) Statement
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference
in which case the user will be required to correct the interference at his expense.
The user is cautioned that changes and modifications made to the equipment without
approval of the manufacturer could void the user's authority to operate this equipment.

JetNet 5310G User Manual
1
Index
1 Introduction........................................................................................................................2
1.1 Overview...............................................................................................................................2
1.2 Major Features .....................................................................................................................5
1.3 Package List.........................................................................................................................7
2 Hardware Installation.........................................................................................................8
2.1 Hardware Introduction ..........................................................................................................9
2.2 Wiring Power Inputs ...........................................................................................................13
2.3 Wiring the Relay Output (DO).............................................................................................14
2.4 Wiring the Digital Input (DI).................................................................................................15
2.5 Connecting the Surge /Lighting protection..........................................................................16
2.6 Wiring Fast Ethernet PoE Ports..........................................................................................16
2.7 DIN Rail mounting Installation ............................................................................................18
3 Preparation for Management ...........................................................................................20
3.1 Preparation for Serial Console............................................................................................20
3.2 Preparation for Web Interface.............................................................................................21
3.3 Preparation for Telnet Console ...........................................................................................24
4 Feature Configuration...................................................................................................... 27
4.1 Command Line Interface Introduction.................................................................................28
4.2 Basic Setting.......................................................................................................................35
4.3 Port Configuration...............................................................................................................54
4.4 Power over Ethernet...........................................................................................................63
4.5 Network Redundancy .........................................................................................................72
4.6 VLAN ..................................................................................................................................92
4.7 Private VLAN....................................................................................................................101
4.8 Traffic Prioritization ...........................................................................................................107
4.9 Multicast Filtering..............................................................................................................113
4.10 SNMP ...............................................................................................................................118
4.11 Security.............................................................................................................................122
4.12 Warning ............................................................................................................................129
4.13 Monitor and Diag ..............................................................................................................137
4.14 Device Front Panel ...........................................................................................................144
4.15 Save to Flash....................................................................................................................145
4.16 Logout ..............................................................................................................................146
5 Appendix........................................................................................................................ 147
5.1 JetNet 5310G Product Specifications ...............................................................................147
5.2 Pin assignment of RS-232 serial console cable................................................................151
5.3 Korenix Private MIB..........................................................................................................152
5.4 Revision History................................................................................................................153
5.5 About Korenix...................................................................................................................154

JetNet 5310G User Manual
2
1 Introduction
Welcome to Korenix JetNet 5310G Series Industrial 8-Port PoE + 2Gigabit Copper /
SFP Managed Ethernet Switch User Manual. Following topics are covered in this
chapter:
1.1 Overview
1.2 Major Features
1.3 Package Checklist
1.1 Overview
Korenix JetNet 5310G, the revolutionary DIN Rail type industrial Gigabit managed Power
over Ethernet Switch is designed with eight 10/100TX PoE injector ports and two Gigabit
RJ-45 / SFP combo ports for highly critical PoE applications such as real time IP video
surveillance, WiMAX systems and Wireless APs. All of the 8 ports of the switch are
compliant with both IEEE 802.3af PoE and IEEE 802.3at high power PoE standards and
can deliver up to 15.4W and 30W power per port to enable the high-power requiring
devices, such as Wireless APs, PTZ and dome network cameras, etc.
The two Gigabit Ethernet combo ports provide high speed uplink to connect with higher
level backbone switches with Korenix MSRTM network redundancy technology, while
ensuring the reliability of video transfer through the exclusive 5ms recovery time. By
supporting various connection types, including 10/100/1000Mbps RJ-45 copper or
100Mbps, 1000Mbps Fiber, the Gigabit uplink ports further enlarge the ring
infrastructure.
With IEC 61000-6-2 / 61000-6-4 Heavy Industrial EMC certified design, including robust
enclosure and -40~75°C wide operating temperature range, JetNet 5310G ensures high
performance of the surveillance network under vibrating and shock environments in
rolling stocks, traffic control systems and other harsh surveillance applications.
Driving the IP Surveillance Market
Since the ratification of the Power over Ethernet standard in 2003, the PoE technology
becomes a trend; more devices adopt PD function to obtain power through Ethernet
cable eliminating the need of running separate power wirings to a remote device. The
JetNet 5310G is equipped with the new PSE solution, compliant with IEEE 802.3af,
IEEE 802.3at 2-event or IEEE 802.3at 2-event plus LLDP standards, as well as forced

JetNet 5310G User Manual
3
mode powering mode for legacy Power over Ethernet cable devices. The 8 PoE ports
support LLDP power negotiation function or 2-Event classification of IEEE 802.3at PoE
plus, and can therefore deliver up to 30W power per port and 120W per unit at 75°C
operating temperature, to drive the IP cameras for cross-street monitoring or WiMAX
systems for internet accesses at train stations, airports or Hot-spots.
100/1000Mbps DDM SFP transceiver for High Quality Monitoring
The SFP sockets of the JetNet 5310G supports 100Mbps and 1000Mbps SFP type fiber
transceiver with speed detection and independent indication. Moreover, it supports DDM
(Digital Diagnostic Monitoring) type SFP transceivers allowing users to diagnose optical
cable transmission problem through maintenance and debugging of the optical signal
quality by DDM without the need of an extra optical cable analyzer, as a result greatly
saving time and system costs.
Rapid Super Ring (RSRTM) Technology
The JetNet 5310G supports Rapid Super Ring technology, which is the 2nd generation of
Korenix Ring Redundancy technology. The recovery time is greatly improved from 30ms
to few ms for both copper and fiber ring. The Ring master can be auto-selected by RSR
engine. The 1st ring port of the R.M. is the primary path while the 2nd ring port of the
R.M. is the block path. Once the primary path fails, the 2nd path will be recovered within
few ms. Besides, the restoration time is also shortened to zero in the R.M. auto-selection
mode.
Comprehensive Redundant Solutions –Multiple Super Ring ( MSRTM)
JetNet 5310G also supports advanced Ring technology –M.S.R. (Multiple Super Ring)
which includes various new technologies for different network redundancy applications
and structures. The supported MSR allows JetNet 5310G aggregating up to 5 Rapid
Super rings includes 4 Fast Ethernet plus 1 Gigabit Ethernet rings into one switch. With
the MSRTM technology, a node can be configured to multiple rings with the failover time.
In addition, users can extend the ring topology by adding hundreds of JetNet managed
switches to meet the large-scale network needs without compromising the network
speed. The MSRTM also allows JetNet 5310G managed switch to easily connect with
core management switches via standard Rapid Spanning Tree Protocol (RSTP) or
through multiple paths or nodes to increase the reliability by RDHTM (Rapid Dual Homing)
technology. By integrating MSRTM and LACP (Link Aggregation Control Protocol), the
JetNet series can enhance the link ability and increase the overall link capacity. Two or
more Fast Ethernet connections are combined in order to increase the bandwidth and to
create a resilient and redundant link.

JetNet 5310G User Manual
4
Seamless Ring Port Restoration TM
Seamless restoration is a new Korenix patented technology which can restore a failed
ring without causing any loop problem, topology change and packet loss. With a 0
second restoration time, this mechanism eliminates any unstable status and guarantees
the applications running non-stop.
Rapid Dual Homing (RDHTM) Technology
Rapid Dual Homing is also the important feature of Korenix new generation Ring
technology. It supports ring coupling with other vendors and with easy configuration and
multiple redundancies, the failover time is much faster and the restoration time is zero
ms. Uplinks can be auto detected and gathered into groups. In each group, uplinks are
sorted into primary, secondary and standbys by their link speed. The uplink with the
highest speed is more likely to be active path for data transmission. Link aggregation is
also integrated into RDHTM. An uplink connection can be a single link or several links
aggregated as a trunk, which provides better redundancy and link capacity.
TrunkRingTM
TrunkRing is a new feature in MSRTM which merges the two technologies of RSRTM and
link aggregation. It takes advantages of aggregation to enhance the link redundancy,
while increase the link speed. The ring will open only if all the aggregated links are
broken. Link aggregation can be achieved by either, static trunk or LACP. Not all the link
sections in a TrunkRing need to be the same. Ring links can be either symmetric or
asymmetric. Some are a single path, and the others are aggregated by links where the
number of links in a trunk group can be different. Users can enhance the link redundancy
at different locations in accordance to the need. And the link with less speed is more
likely to be used as the backup path for restoring the network to full play capacity.
Link Aggregation Control Protocol
Link Aggregation Control Protocol allows you grouping multiple Ethernet ports in parallel
to increase the link bandwidth. The aggregated ports can be viewed as one physical port,
so that the bandwidth is higher than just one single Ethernet port. The member ports of
the same trunk group can balance the loading and backup with each other. The LACP
feature is usually used when you need higher bandwidth for the backbone network. This
is a cost-effective way for you to transfer much more data.
Multi Powering Mechanism- User Manual, Forced and IEEE 802.3at LLDP Power
over Ethernet

JetNet 5310G User Manual
5
Some of Legacy PD devices also feature user defined manual mode and forced
powering mode to support non-standard PD devices without the PoE signature resistor
for some WiMax systems, which are non-compliant with IEEE 802.3at LLDP Power over
Ethernet.
For the new PoE standard –IEEE 802.3at, JetNet Switch implements Link Layer
Discovery Protocol (LLDP) into the system for allowing power budget negotiation
between PD devices while providing smart power budget control behavior.
Auto Topology Discovery & Efficient Management through LLDP and JetView Pro
i2NMS
JetNet 5310G supports topology discovery or LLDP (IEEE 802.1AB Link Layer
Discovery Protocol) function that can help users to discover multi-vendor’s network
devices on the same segment by an NMS system which supports LLDP function. With
LLDP function, NMS can easily maintain the topology map, display port ID, port
description, system description, VLAN ID and so on. Once a link failure happens, the
topology changed events are updated to the NMS to help users easily maintain the
network system. Like as the JetView Pro, not only supports topology discovery, it also
delivers group IP assignment, firmware upgrade, configuration files backup/
restore ,SNMP MIB Browser /compile, MSRTM group management and also allows user
to export topology map to drawing file-JPEG, BMP, PNG or PDF for other application.
Outstanding Management and Enhanced Security
The JetNet 5310G provides various network control and security features to ensure the
reliable and secure network connection. To optimize industrial network environment the
switch supports advanced network features, such as Tag VLAN, IGMP Snooping, Quality
of Service (QoS), Link Aggregation Control Protocol (LACP), Rate Control, etc. The PoE
switch can be smartly configured through JetView, JetView Pro (Korenix’s advanced
management utility), Web Browser, SNMP, Telnet and RS-232 local console with its
command like interface. The failure notifications are sent through e-mail, SNMP trap,
Local/Remote system log, Multiple event alarm relay.
To avoid hacker’s attacks and ensure the secure data transmission, JetNet 5310G series
features DHCP client, DHCP server with IP and MAC binding, 802.1X Access Control,
SSH for Telnet security, IP Access table, port security and many other security features.
1.2 Major Features
Korenix JetNet 5310G Switch have following features:

JetNet 5310G User Manual
6
8 10/100 Base TX PoE ports and 2 Gigabit RJ/ SFP combo ports
IEEE 802.3af 15.4W / IEEE 802.3at 30W High Power PoE
120W total power budget for High-power PoE camera
SFP ports support 100/1000 Mbps with Digital Diagnostic Monitoring (DDM) to
monitor long distance fiber quality
All ports support Korenix patented RSR with 5ms recovery time, and MSR for up
to 4 x 100M Rings plus 1 Gigabit Ring
Advanced management by LACP/VLAN/Q-in-Q/Private VLAN/ GVRP/ QoS/ IGMP
Snooping/Rate Control/ Online Multi-Port Mirroring/ Advanced DHCP server,
Client
Advanced Security system by Port Security, Access IP list, SSH and HTTPS
Login
Event Notification through E-mail, SNMP trap and SysLog
IEEE 802.1AB LLDP and optional JetView Pro i2NMS software for auto-topology
and group management
Cisco-Like CLI, Web, SNMP/RMON for network Management
Multiple event relay output for enhanced device alarm control
Hi-Pot Isolation Protection for ports and power
Industrial Heat dispersing design, -40~75˚C wide operating temperature
Note: The detail spec is listed in Appendix 5.1

JetNet 5310G User Manual
7
1.3 Package List
Korenix JetNet 5310G is shipped with following items:
JetNet 5310G
One DIN-Rail clip (attached to the switch)
One RS-232 DB-9 to RJ-45 console cable
CD User manual x 1
Quick Installation Guide (QIG)
If any of the above items is missing or damaged, please contact your local sales
representative.
DB-9 to RJ-45
Cable
CD User
Manual
QIG
JetNet 5310G

JetNet 5310G User Manual
8
2 Hardware Installation
This chapter includes hardware introduction, installation and
configuration information.
Following topics are covered in this chapter:
2.1Hardware Introduction
Dimension
Panel Layout
Bottom View
Rear Side
2.2Wiring Power Inputs
2.3Wiring the Relay Output (DO)
2.4Wiring the Digital Input (DI)
2.5Connecting the Surge/ Lighting Protection
2.6Wiring Ethernet Ports
2.7Wall-mounting Installation

JetNet 5310G User Manual
9
2.1 Hardware Introduction
Dimension –
JetNet 5310G w/o DIN Rail mounting kit: 95(W) x 127 (D)x 160(H)
JetNet 5310G w/ DIN Rail mounting kit: 95(W) x 136.2 (D)x 160(H)

JetNet 5310G User Manual
10
Panel Layout
The front panel includes 8 x 10/100Mbps RJ-45 PoE ports, 2 x Gigabit
Ethernet RJ-45/SFP socket ports, 1 RJ-45 for RS232 console, System
diagnostic LEDs, Port LEDs, PoE status LEDs.
Bottom view
The bottom side includes 2 4-pin terminal block connectors and 1 chassis
grounding screw. One of 4-pin terminal block connectors is for power inputs,
and the rest is for alarm relay output and digital input.

JetNet 5310G User Manual
11
Rear Side
The rear side back panel attached DIN rail clip and one lighting screw to
make connection with chassis ground and Switch inner lighting protection
circuit.
The product label is also sticked on the bottom side of DIN rail clip, in case if it is
missed, please contact with your sales representive for product change.

JetNet 5310G User Manual
12
This label indicates that the type of
PoE is Type-2 high power PSE and
performs PoE powering by
Alternative-A mode (1,2,3,6)
PoE 15W x8 / 75°C

JetNet 5310G User Manual
13
2.2 Wiring Power Inputs
The Power input port is located at the bottom side, and provides 2 power input
connections in one 4-pin removable terminal block. The power port support
polarity reverse protection; the Switch won’t start if wrong polarity applied. The
wiring architecture please refers to below figure.
Wiring the Power Inputs
1. Insert the positive and negative wires into the V+ and V- contact on the
terminal block connector.
2. Tighten the wire-clamp screws to prevent the power wires from being
loosened.
3. Connect the power wires to suitable AC/DC Switching type power supply.
The JetNet 5310G provides Power over Ethernet function and is compliant
with IEEE802.3af/ IEEE802.3at standards; therefore, the input DC voltage
should be in the range of DC 46V to DC 57V.
For the safety issue, turn off AC power input source before connecting the
AC/DC Power supply module and the terminal block connectors. Besides, don’t
turn-on the source of AC/DC power module and make sure all connections were
well done then power on the AC source to powering the Switch device.
Otherwise, your screwdriver blade may inadvertently short your terminal
connections to the grounded enclosure and cause damage.
Notes: Use the UL Listed LPS Power supply with output Rating 46~57V Vdc,
minimum 2.5A currents. Here, we recommended using DC 48V as the operating
voltage. It is recommended to use 48vdc power supply.

JetNet 5310G User Manual
14
2.3 Wiring the Relay Output (DO)
The relay output contacts are in the bottom side as shown on below figure. The
relay output (DO) is controlled by the pre-defined operating rules. To activate
relay output function, please refer to the CD User’s Manual for more Relay
Output management information.
Note: The relay contact only supports 0.5 A current, DC 24V. It is not recommended to apply
voltage and current higher than the specifications.

JetNet 5310G User Manual
15
2.4 Wiring the Digital Input (DI)
The Digital Input (D.I.) contacts are in the bottom side of the device as shown in
below figure.
It accepts one external DC type signal input and can be configured to send alert
message through Ethernet when the signal is changed. The signal may trigger
and generated by external power switch, like as door open trigger switch for
control cabinet.
Note: the DI accepts DC type signal and supports isolated input circuit with Digital High
Level input DC 11V~30V and Digital Low Level input DC 0V~10V. Do not apply voltage that
higher than the specification; it may cause internal circuit damage or a wrong action of DI.

JetNet 5310G User Manual
16
2.5 Connecting the Surge /Lighting protection
There is one screw fixed on the rear side for lighting /surge protection; tighten
and wire to chassis grounding to obtain better surge/ lighting immunity. But, do
remember remove the surge grounding screw before to insulation/Hi-pot testing.
In case you do not, the protectors may damage during the testing, and the
lighting protection will malfunction.
Never install or work on/with the equipment or the cabling during the
period of its lightning activity.
2.6 Wiring Fast Ethernet PoE Ports
The JetNet PoE Switch support 8 10/100Mbps Fast Ethernet ports with power
over Ethernet (PoE) PSE function, and 2 Gigabit 10/100/1000Mbps RJ-45/SFP
combo ports. Both of Gigabit combo ports provide SFP transceiver plug-in with
first priority function.
Fast Ethernet Ports
The Fast Ethenert ports (1~8) comply with IEEE 802.3af / IEEE802.3at function
with 120watts system power budget control function ( enabled from firmware
v1.2a); the PoE ports support alternative-A type powering method, and forward
power through the RJ-45 conductors 1, 2, 3 and 6. If the power device (PD) is not
fully compliant with IEEE 802.3af / IEEE 802.3at, then it will not be powering. So,
Note: 1. Ensure the Surge/Lighting is well connecting with Chassis Grounding
2. Remove the Surge /Lighting Screw, before performing Insulation /
Hi-pot Testing.

JetNet 5310G User Manual
17
before connecting the PD device, please ensure the PD you have bought is
compliant with PoE standard. The RJ-45 plug’s conductor pin assignment shows
as following table for your reference.
RJ-45 conductor
Type of Signal
Polarity of power
Note
1
RxD +
V -
Alternative-A
2
RxD -
V -
Alternative-A
3
TxD +
V+
Alternative-A
6
TxD -
V+
Alternative-A
Note: The PD device should accept power from either 1,2,3,6 (data pairs) or
4,5,7,8 (spare pairs); for the detail information, please refer to IEEE 802.3at / IEEE
802.3af Power over Ethernet standard.
Gigabit Ethernet /SFP combo port
The JetNet 5310G provides 2 Gigabit RJ-45/ SFP combo ports that with different
link speed –10Mbps, 100Mbps, 1000Mbps, and compliant with the standards of
IEEE 802.3 10Base-T, IEEE 82.3u 100Base-TX, IEEE 8023.u 100Base-FX, IEEE
802.3ab 1000Base-T, and IEEE 802.3z Gigabit fiber.
The combo prots support SFP transceiver plug-in high priority function; thus, don’t
connect Ethernet RJ-45 and insert SFP transceiver at the same time; it will cause
the port being activated in wrong status.
The SFP ports also provide Digital Diagnostic Monitoring function, it can assist
user to monitor the quality of optical signal, and diagnose the transmission of fiber.
This function is only available for Korenix certified DDM SFP transceiver, and does
not support third party transceiver that may not fully comply with MSA SFP
transceiver standard.
By the DDM function, user can get real information including the strength of
received optical signal, launched optical signal and current operating temperature
of SFP transceiver, and the specification of transceiver.
The following diagram shows the information captured from WEB user interface.
Range: the specification of Korenix defined.
Current: actual value read from SFP transceiver.
Tx Power (dBm): optical strength of received.
Rx Power (dBm): optical strength of launched.
Note: The Ethernet Switch has to use UL recognized fiber transceiver with Class 1
Laser/LED Diode.