Korenix JetNet 6710G User manual

JetNet 6710G / 6810G Series
Industrial 8-Port PoE plus 2 Gigabit-TX
Managed Etherenet Switch
Quick Installation Guide
www.korenix.com
V1.0

1. Overview
The JetNet 6710G/6810G series are Managed Industrial Power over Ethernet Switches,
equipped with eight 10/100 TX ports with 15.4 watts PoE injector and dual 10/100/1000 TX
ports for uplink connection.
By software configuration or by LLDP auto detection, the eight 10/100 TX PoE injector ports
of JetNet 6710G series can deliver 15.4W by IEEE 802.3af or 30W by the latest High Power
PoE IEEE 802.3at standard for supporting High Power Requiring Devices (PD).
Besides, the eight IEEE 802.3af PoE injector ports of JetNet 6810G series are designed with
the Korenix patented Booster PoE technology, which allows the switches to adopt 24~57VDC
input and deliver 15.4W per port at 48V for applications where DC 48V power supply is not
available.
The 2 Gigabit Ethernet ports can provide high speed uplink connectivity to higher level
backbone switches with Korenix MSRTM network redundancy technology, which can recover
any failure in less than 5milliseconds. To work under vibration and shock environments, the
switches are designed with industrial D-coded M12 connectors or rugged RJ45 connectors to
ensure exceptional solid Ethernet and PoE connections.
1-1 Packing List Checking
The JetNet 6000G series is shipped with the following items. If any of these items is missing
or damaged, please contact your customer service representative for assistance.
JetNet 6710G Managed High Power
IEEE 802.3at PoE Switch (M12 / Rugged RJ)
JetNet 6810 Managed Booster PoE
Switch ( M12 / Rugged RJ)
M12 on DB9 Shielded Console Cable
Rugged M12 D-coded 4-pole
Field Assemble able Connecter
Rugged M12 A-coded 8-pole
Field Assemble able Connector
Rugged RJ45 Field Assemble
able Connecter
2 Wall-Mount kits & 8 Screws
Quick Installation Guide
Documentation and Software CD-ROM
JetNet
6710G-M12
JetNet
6710G-RJ
JetNet
6810G-M12
JetNet
6810G-M12
1
1
1
1
1
1
111 1
11
11
11
88
22
11
10 10
1
1

1-2 Introduction to the Manual
2. Appearances
The following manuals are included as PDF files on the CD-ROM:
4Quick Installation Guide: includes information on installing all versions of JetNet 6710G /
6810G series PoE Switch
4User manual – Configuration: applied to the managed versions of JetNet 6710G/
6810G series PoE Switch
3. Hardware Installation
3-1 Powering of the system
The Power input port is located at the top of the front panel and supports redundant input
function via a proprietary assembly capable IP-67 connector (CDG-L207SA) included in the
shipment. If you cannot find this power connector, please contact your local distributor. For
the available input power range and recommended cable size, please refer to the below
table.
Recommended
48
48
24
24
Maximum
60
60
60
60
Minimum
48
48
22
22
Redundant Input
V1, V2
V1, V2
V1, V2 bind together
V1, V2 bind together
AWG No. / Cable
Area (mm2)
AWG 14 / 2.0
AWG 14 / 2.0
AWG 14 / 2.0
AWG 14 / 2.0
JetNet 6710G-M12
JetNet 6710G-RJ
JetNet 6810G-M12
JetNet 6810G-RJ
Power Input (DC Voltage) Input Conductor Cable Size
Redundant
Power Input
Console
Port Alarm
Output
8x10/100 Base-TX PoE
M12 D-coding
2x1000 Base-T
M12 A-coding
LED: Power, PoE Status, Port Status,
Alarm, System Status, Ring Status
JetNet 6710G-M12 JetNet 6710G-RJ
Redundant
Power Input
Console
Port Alarm
Output
8x10/100 Base-TX PoE
M12 D-coding
2x1000 Base-T
M12 A-coding
LED: Power, PoE Status, Port Status,
Alarm, System Status, Ring Status

The JetNet 6810G only supports single power input that binds V1 and V2 together to obtain
higher current for the booster.
Use the UL listed Switching power supply to power the JetNet Switch. For the power wiring
method, please refer to the figures 3.1-1 and 3.1-2. For system safety and the anti-immunity
ability, the chassis ground screw should be well grounded to the earth ground.
Figure 3.1-1. Power Supply wiring architecture
Note:
E.G: Earth
Grounding
Figure 3.1-2 Power connector assembly diagram
The RS-232 console and the alarm relay are
connected via the assembly type of 5-pole M12
A-coding connector included in the supplied
package of JetNet switch. The following figure
3-2-1 is the disassembly diagram of M12
A-coding connector.
In the M12 connector packing, the parts 1, 2, 3
are already assembled.
Follow the steps for soldering and assembling
the cable and connector together: Figure 3.2-1 Field Assemble
M12 disassembly connector
3.2 RS-232 console and Relay Output Connection

Step -1: Slide component 4, 5, 6 and then 7 over the console
cable. Keep them loose. Do not tighten them yet. 2 cable glands
are provided for cable diameter from 3.5 to 5.8 mm. Choose the
one that best fits the cable.
Step-2: Solder the conductors with the copper
wires according to the pin assignment. The
soldering side view of the pin is shown as below:
Console port pin assignment
Step-3: Fasten the components
4, 5, 6 and 7 in sequence. Be
sure the gasket is on the right
position. See the below M12
assembly diagram: 2. Insert part 6-seal into part 5.
4. Finalized
1. Assembly part 1 and 4,
ensure the solder pins are
protected by part 4-gasket,
then locking part 1 and 5.
3. Locking part 5 and 7.
Never install or work on/with the equipment or the
cabling during the period of its lightning activity.
3.3 Assembly of Ethernet Patch Cables
You can connect terminal devices and other segments via twisted pair cables. Ports which
are not assigned should be closed with the covering caps contained in the package list of
delivery to guarantee the connector is clear without rust.
!

3.3.1 Assembly of M12 Ethernet
Connector
For Fast Ethernet M12 D-Code to M12
D-Code connection, you can use either
version below:
M12-to-M12 Ethernet Cable Wiring
For Fast Ethernet M12 D-Code to RJ45
connection, the pin assignment of the patch
cable is shown below:
M12-to-RJ45 Ethernet Cable Wiring
For Gigabit Ethernet M12 A-Code to RJ45 connection, the pin assignment of the patch
cable is shown below:
Gigabit M12-to-RJ45 Ethernet Cable Wiring
M12-to-RJ45 Ethernet Cable Wiring
3.3.2. Assembly of Rugged RJ45 Connector
The RJ version provides robust connection by the
field assembly capable rugged RJ45 connector.
Each component of the connector is shown below:
3.3.2-1 Rugged RJ45 Connecter Components

Follow the steps to assemble the rugged RJ45 connector:
M12-to-RJ45 Ethernet Cable Wiring
RJ45 Cable color code
Following picture-19 shows the color code of Cat.-5E UTP/STP cable based on the two
standards released by TIA/EIA – 568A and 568B. The 568B wiring is by far, the most
common wiring method. You can choose the method that suits your application; but
ensure that both ends of the cable use the same standard.

4. Device Management
4.1 Preparation for console management
Attach the RS-232 DB9 connector to your PC’s COM port. Connect the M12 A-code 5-pin
connector to the console port of the JetNet 6710G/6810G.
JetNet 6710G / 6810G series switches provide both in-band and out-band configuration
methods. You can configure the switch via the RS232 console with the attached console
cable, or you can remotely manage the switch via network using Telnet/SSH, Web/HTTPS
management.
3.4 Wall /Panel Mounting Installation
The JetNet 6710G/6810G series are shipped with 1 set mounting bracket which allows users
to install JetNet 6710G/6810G on the panel or wall. Assemble the brackets on the rear side
of JetNet 6710G/6810G body, then using a suitable screw install onto wall / panel of cabinet
with good heat dissipation.
4.1.1 Go to Start -> Program -> Accessories -> Communication -> Hyper Terminal
4.1.2 Give a name to the new console connection to create a new serial communication
session.
4.1.3 Choose the COM name, and select the correct serial settings. The serial settings of
JetNet 6710G/6810G are as below:
Baud Rate: 9600 / Parity check: None / Data Bit: 8 / Stop Bit: 1

4.2 Preparation for Web management
Before you attempt to use the embedded web interface to manage switch operation, verify
that your JetNet switch is properly installed on your network and that every PC on this
network can access the switch via the web browser.
4.2.1 Launch the web browser (Internet Explorer or Mozilla Firefox) on the PC.
4.2.2 Type http:// 6710G_IP_Address or 6810G_IP_Address (The default IP address is
192.168.10.1.), then press Enter.
4.2.3 The login screen will appear next. Type-in the user name and the password. The
default user name and password is admin/admin.
4.2.4 Click OK, and then the welcome page of the web-based management interface will
appear.
At the left column of the Web management interface are listed the available software
features; by pressing the ring column you can also view the detailed configuration
interface.
For more detailed management features please refer to the software’s users’ manual. The
software user manual can be downloaded from Korenix Website as below:
http://www.korenix.com/downloads.htm
4.1.4 After connected, you can see Switch login request. Type-in the username and
password to login. The default username is “admin”, password is “admin” for console
interface.
4.1.5 Follow the manual to configure the device features.

Ѯᢊடց
ี݂಑ I 321415!ဴ
ี݂಑ I 313547 ဴ
ཱི࠮಑ M 339841 ဴ
ཱི࠮಑ M 339840 ဴ
Patent No. (Taiwan):
Granted Invention: I 321415
Granted Invention: I 313547
Utility Model: M339840
Utility Model: M339841